Study of the influence of interface normal stresses on the bond behavior of FRCM composites using direct shear and modified beam tests
Source abstract
Abstract
Abstract In the last decades, the increasing need for strengthening and retrofitting of existing masonry members has led the scientific community toward the development of innovative strengthening systems. Among these systems, inorganic-matrix composite materials have been gaining increasing popularity due to their effectiveness, relatively low cost, ease of the application, and reversibility of the intervention. Inorganic-matrix composites, usually referred to as fiber- (or fabric-) reinforced cementitious matrix (FRCM) composites, were successfully used as externally bonded reinforcement (EBR) of masonry members subjected to various load combinations. However, their effectiveness is strictly related to the FRCM-substrate bond behavior. Therefore, numerous set-ups were employed to investigate the bond properties of FRCM composites. Among them, single-lap direct shear test set-ups were the most commonly employed and are now recommended by available design guidelines for FRCM composites. In this paper, a modified beam (MB) test set-up is used to study the bond behavior of two different FRCM composites: a polyparaphenylene benzobisoxazole (PBO) FRCM and a carbon FRCM. The parameters studied are the dimensions of the blocks used in the MB tests and the presence of bare or embedded fibers at the gap between the blocks. The bond behavior observed is compared with that of single-lap direct shear tests of the same FRCM composites. The results obtained provide an insight on the influence of normal stress components at the matrix-fiber interface on the FRCM bond behavior, which may play an important role in the capacity of FRCM strengthened curved members.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Masonry and Concrete Structural Analysis · Structural Behavior of Reinforced Concrete · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. Fiber-reinforced polymer composites for construction—state-of-the-art review10.1061/(ASCE)1090-0268(2002)6:2(73) ↗
2. Out-of-plane behaviour of infill masonry panels strengthened with composite materials10.1617/s11527-014-0384-6 ↗
3. First-aid and provisional devices in historical structures with collapse risk after seismic shock10.4028/www.scientific.net/KEM.817.301 ↗
4. Mortar-based systems for externally bonded strengthening of masonry10.1617/s11527-014-0360-1 ↗
5. ACI Committee 549, Guide to Design and construction of externally bonded fabric-reinforced cementitious matrix (FRCM) systems for repair and strengthening concrete and masonry structures; ACI 549.4R-13. ACI, Farmington Hill, US, 2013.
6. National Research Council · 2018
7. Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: out-of-plane cyclic loading10.1617/s11527-007-9226-0 ↗
8. Challenges and perspectives for the protection of masonry structures in historic centers: the role of innovative materials and techniques10.21809/rilemtechlett.2016.10 ↗
9. Experimental analysis on bond between PBO-FRCM strengthening materials and concrete10.1016/j.compositesb.2012.03.011 ↗
10. Bond between textile-reinforced mortar (TRM) and concrete substrates: experimental investigation10.1016/j.compositesb.2016.05.041 ↗
11. Analysis of the bond between Fabric Reinforced Cementitious Mortar (FRCM) strengthening systems and concrete10.1016/j.compositesb.2014.10.027 ↗
12. Bond characteristics of different FRCM systems10.1016/j.conbuildmat.2018.04.216 ↗
13. Contribution to direct tensile testing of textile reinforced concrete (TRC) composites10.1016/j.msea.2011.08.009 ↗
14. Influence of experimental setups on the apparent uniaxial tensile load-bearing capacity of Textile Reinforced Concrete specimens10.1617/s11527-011-9775-0 ↗
15. Micromechanical modeling of the constitutive response of FRCM composites10.1016/j.conbuildmat.2019.117539 ↗
16. Experimental investigation of tensile and bond properties of Carbon-FRCM composites for strengthening masonry elements10.1016/j.compositesb.2017.06.018 ↗
17. Mechanical characterization of different FRCM systems for structural reinforcement10.1016/j.conbuildmat.2017.04.051 ↗
18. Single-lap shear bond tests on steel reinforced geopolymeric matrix-concrete joints10.1016/j.compositesb.2016.11.005 ↗
19. Analytical solution of the bond behavior of FRCM composites using a rigid-softening cohesive material law10.1016/j.compositesb.2019.107051 ↗
20. Carloni C. Analyzing bond characteristics between composites and quasi-brittle substrates in the repair of bridges and other concrete structures. In: Kim YJ, editor. Advanced Composites in Bridge Construction and Repair. Chapter 3, Woodhead Publishing; 2014, pp. 61–93. doi:10.1533/9780857097019.1.61.10.1533/9780857097019.1.61 ↗
21. Modeling of mixed-mode debonding in the peel test applied to superficial reinforcements10.1016/j.ijsolstr.2008.05.024 ↗
22. A new 3D experimentally consistent XFEM to simulate delamination in FRP-reinforced concrete10.1016/j.compositesb.2016.01.024 ↗
23. Three-dimensional numerical modeling of single-lap direct shear tests of FRCM-concrete joints using a cohesive damaged contact approach10.1061/(ASCE)CC.1943-5614.0000827 ↗
24. Extrados strengthening of brick masonry arches with PBO–FRCM composites: experimental and analytical investigations10.1016/j.compstruct.2016.04.030 ↗
25. Assessment of curved FRP-reinforced masonry prisms: experiments and modeling10.1016/j.conbuildmat.2013.11.011 ↗
26. Debonding of composites on a curved masonry substrate: experimental results and analytical formulation10.1016/j.compstruct.2014.02.004 ↗
27. A bending test set-up for the investigation of the bond properties of FRCM strengthenings applied to masonry substrates10.4028/www.scientific.net/KEM.817.149 ↗
28. A.S. Calabrese, T. D’Antino, P. Colombi, C. Poggi, Study of the bond behavior of FRCM-masonry joints using a modified beam test. Proceedings of the twenty-fourth Italian Association of Theoretical and Applied Mechanics Convention (AIMETA 2019), Rome, Italy: The Italian Association of Theoretical and Applied Mechanics; 2019.10.1007/978-3-030-41057-5_38 ↗
29. Modified hinged beam test on steel fabric reinforced cementitious matrix (SFRCM)10.1016/j.compositesb.2018.03.019 ↗
30. Determination of the interfacial properties of SRP strips bonded to concrete and comparison between single-lap and notched beam tests10.1016/j.engfracmech.2017.09.020 ↗
31. A comparison of the bond behavior of PBO-FRCM composites determined by double-lap and single-lap shear tests10.1016/j.cemconcomp.2015.07.007 ↗
32. G. de Felice, T. D’Antino, S. De Santis, P. Meriggi, F. Roscini, Lessons learned on the tensile and bond behavior of fabric reinforced cementitious matrix (FRCM) composites, Front. Built. Environ. 6 (2020). doi:10.3389/fbuil.2020.00005.10.3389/fbuil.2020.00005 ↗
33. Effects of environmental conditioning on the bond behavior of FRP and FRCM systems applied to concrete elements10.1061/(ASCE)EM.1943-7889.0001375 ↗
34. Out-of-plane maximum resisting bending moment of masonry walls strengthened with FRCM composites10.1016/j.compstruct.2018.04.054 ↗
35. Relationship between the effective strain of FRCM-strengthened RC beams and the debonding strain of direct shear tests10.1016/j.engstruct.2020.110631 ↗
36. S.R.L. Ruregold, Technical datasheet of PBO-Mesh Gold 70/18, 2019.
37. S.R.L. Ruregold, Technical datasheet of C-Mesh Gold 84/84, 2019.
38. European Committee for Standardization, Methods of test for mortar for masonry. Determination of flexural and compressive strength of hardened mortar. EN 1015-11:1999, CEN, Brussels, Belgium, 1999.
39. Terreal San Marco. Technical datasheet 2017. https://sanmarco.it/scheda-prodotto.php?id-categoria=2&id-prodotto=36 (accessed August 15, 2019).
40. Effect of concrete composition on FRP/concrete bond capacity10.1061/(ASCE)1090-0268(2007)11:6(611) ↗
41. Bond between carbon fabric-reinforced cementitious matrix and masonry substrate10.1061/(ASCE)MT.1943-5533.0002561 ↗
42. CSLLPP - Servizio Tecnico Centrale. Linee guida per la identificazione, la qualificazione ed il controllo di accettazione di compositi fibrorinforzati a matrice inorganica (FRCM) da utilizzarsi per il consolidamento strutturale di costruzioni esistenti. Rome, Italy, 2019
43. Carbon-FRCM materials for structural upgrade of masonry arch road bridges10.1016/j.compositesb.2015.01.024 ↗
44. Experimental investigation of bond between glass textile reinforced mortar overlays and masonry: the effect of bond length10.1617/s11527-017-1033-7 ↗
45. Effect of inclining angle, bundling and surface treatment on synthetic fibre pull-out from a cement matrix10.1016/0010-4361(90)90005-H ↗
46. The fibre pull-out energy of misaligned short fibre composites10.1023/A:1018593931951 ↗
47. Debonding behavior of ancient masonry elements strengthened with CFRP sheets10.1016/j.compositesb.2012.04.029 ↗
48. Effect of the inherent eccentricity in single-lap direct-shear tests of PBO FRCM-concrete joints10.1016/j.compstruct.2016.01.076 ↗
49. FRP-masonry interfacial debonding: an energy balance approach to determine the influence of the mortar joints10.1016/j.euromechsol.2015.08.003 ↗