Structural performance of the finger-jointed strength of some wood species with different joint configurations
Source abstract
Abstract
Abstract This study was conducted to evaluate the effects of adhesive type, wood species, and finger joint configurations on structural performance of the finger joint. The wood species studied were oriental beech (Fagus orientalis lipsky.), oak (Quercus robur), Scots pine (Pinus sylvestris lipsky.), poplar (Populus tremula lipsk.) and Uludag fir (Abies bormulleriana Matff.) and adhesives were poly(vinyl acetate) (PVAc), Desmodur-VTKA (D-VTKA). However, there is little information available concerning the bending strength and modulus of elasticity for finger joints in these field. In this study, it was aimed to determine the bending strength and modulus of elasticity for finger joints. For this purpose, samples were tested according to the TS EN 310 standard. It was observed that the highest bending strength and modulus of elasticity were obtained in beech control (solid wood) samples. As for the finger joints, after the control samples, the highest bending strength value (57.4 N/mm2) was obtained from Oriental beech wood samples having a 21 mm finger length and bonded with PVAc adhesive, the highest modulus of elasticity (8885.3 N/mm2) was obtained from beech wood samples having a 21 mm finger length and bonded with PVAc adhesive. As a result of the effects of finger joints on bending strength and modulus elasticity test, if the length of finger joints increases up to 21 mm, the properties of bending strength increase.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Wood Treatment and Properties · Tree Root and Stability Studies · Forest Biomass Utilization and Management
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (17)
Show source-provided references
1. Centre Technique du Bois (CTBA). Technical and economic study of finger-jointing. Book No. 92. Paris, France [in French]. 1973. p. 48.
2. Jokerst RW. Finger-jointed wood products. Res Pap FPL-382 USDA Forest Service, Madison: Forest Prod Lab; Wis. 1981. p. 25.
3. Finger-joint connected (FJC) wood truss system
4. High-strength corner joints for wood
5. Glued laminated timber
6. Tapered double cantilever beam fracture tests of phenolic-wood adhesive joints. Part I. Development of specimen geometry; effects of bondline thickness, wood anisotropy and cure time on fracture energy
7. River B. Fracture of adhesive-bonded wood joints. In: Pizzi, Mitall, editors. Handbook of adhesive technology, 1994. p. 151–77.
8. Study of stress dispersion
9. Effect of adhesive stiffness and thickness on stress distributions in structural finger joints10.1080/00218469408026617 ↗
10. Producer firm, Bitlis Group Izmit, Data sheets. Turkey, 2000.
11. TS 3891. Adhesives-polyvinyl acetate emulsion (for wood). Ankara: Institute of Turkish Standards; 1992.
12. TS 2471 Wood. Determination of moisture content for physical and mechanical tests. Institute of Turkish Standards, 1976.
13. BS EN 204. Non-structural adhesives for joining of wood and derived timber products. England: BS (British Standards); 1991.
14. TS EN 310. Wood-based panels. Determination of modulus of elasticity in bending and of bending strength. Institute of Turkish Standards, 1999.
15. An analysis of structural finger joints made from two northeastern species
16. Bonding strength of adhesives in wood materials impregnated with imersol-aqua10.1016/j.ijadhadh.2003.10.007 ↗
17. Influence of bondline brittleness and defects on the strength of timber finger-joints10.1016/S0143-7496(98)00048-7 ↗