journal article·2016-11Open access

Moisture resistance and compactibility of asphalt concrete produced in half-warm mix asphalt technology with foamed bitumen

Anna Chomicz-Kowalska, Władysław Gardziejczyk, Mateusz M. Iwański

Abstract

Current regulations regarding emissions, as well as the efforts focused on reducing energy intensity of building materials production create a need for implementing new road construction technologies. Particular attention is being paid to the lowering of asphalt concrete production temperature, which is about 160 °C. In response to this need warm mix asphalt (WMA) technologies have been developed which allow producing asphalt mixes at temperatures about 20–30 °C lower than those of conventional methods. However, it was only after half warm mix asphalt (HWMA) was introduced that the mixing temperature of asphalt concrete with foamed bitumen could be reduced by as much as 60 °C. Asphalt pavements constructed with HWMA may have a reduced service life and lower resistance to environmental factors (e.g. water). This paper presents the results from the tests with one freeze cycle and from the moisture sensitivity analysis conducted for the low-temperature asphalt concrete (AC 8) with foamed bitumen and the control mix produced according to conventional hot mix asphalt technology. It was found that the modification of 50/70 bitumen (before foaming) with the addition of 2.5% FT synthetic wax had a beneficial effect on the properties of asphalt concrete mixes under investigation. The ITSR indices were compared having been determined in accordance with procedures based on European and AASHTO standards that are widely used in Poland. The analysis was extended to include the compactibility evaluation of low-temperature bituminous mixes and the impact of air voids on the mechanical parameters. The foamed asphalt concrete modified with 2.5% FT wax was found to satisfy the requirements for moisture resistance determined during the test with one freeze cycle.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Analysis and evaluation of possibilities for the use of warm mix asphalt in Lithuania10.3846/1822-427X.2009.4.80-86 ↗
2. Optimization of warm mix asphalt using different blends of binders and synthetic paraffin wax contents10.1016/j.conbuildmat.2010.02.030 ↗
3. Evaluation of sustainable technologies that upgrade the binder performance grade in asphalt pavement construction10.1016/j.matdes.2016.01.065 ↗
4. Estimation of resistance to moisture destruction in asphalt mixtures10.1016/j.conbuildmat.2008.11.007 ↗
5. The influence of aggregate, filler and bitumen on asphalt mixture moisture damage10.1016/j.conbuildmat.2007.07.009 ↗
6. Theory and measurements of bitumen binders adhesion to aggregate
7. The effect of using lime and styrene–butadien–styrene on moisture sensitivity resistance of hot mix asphalt10.1016/j.conbuildmat.2008.08.019 ↗
8. Predicting stropping and moisture induced damage of asphalt concrete prepared with polymer modified bitumen and hydrated lime10.1016/j.conbuildmat.2008.12.001 ↗
9. M. Iwański, A. Chomicz-Kowalska, J. Mrugała, Application of the synthetic wax to improve the foamed bitumen parameters used in half-warm bituminous mixtures. 9th International Conference Environmental Engineering. Procedia Engineering, Vilnius, Lithuania, 2014. doi: 10.3846/enviro.2014.154.10.3846/enviro.2014.154 ↗
10. Evaluation the mechanism of the effect of hydrated lime on moisture damage of warm mix asphalt10.1016/j.conbuildmat.2013.05.079 ↗
11. Effect of asphalt film thickness on the moisture sensitivity characteristics of hot-mix asphalt10.1016/j.buildenv.2006.10.006 ↗
12. Evaluation of the pavement performance
13. K.J. Jenkins, A.A.A. Molenar, J.L.A. de Groot, M.F.C. Van de Ven, Optimization and Application of Foamed Bitumen in Road Building. Vegbouwkundige Werkdagen, Doorwerth, Nederlandes, 2000.
14. Development of (half-) wam foamed bitumen mixes: state of the art10.1080/10298430601149635 ↗
15. Application of synthetic wax for improvement of foamed bitumen parameters10.1016/j.conbuildmat.2015.02.060 ↗
16. EN 12697-12. Bituminous mixtures. Test methods for hot mix asphalt. Determination of the water sensitivity of bituminous specimens.
17. D. Sybilski, et al., Sprawozdanie końcowe z pracy: Weryfikacja i uaktualnienie metody badawczej wodoodporności z cyklem zamrażania mieszanek mineralno-asfaltowych. Temat TN-255. Etap III – Zadanie 7,8. [Final progress report: Verification and updating of water resistance test method with a freeze-thaw cycle of bituminous mixtures]. Road and Bridge Research Institute, Warsaw, 2013.
18. EN 12697–12:2008. Bituminous mixtures. Test methods for hot mix asphalt. Determination of the water sensitivity of bituminous specimens.
19. AASHTO T283–89. Standard Method of Test for Resistance of Compacted Bituminous Mixture to Moisture Induced Damage, Standard Specifications for Transportation Materials and Methods of Sampling and Testing.
20. J. D’Angelo, et al., Warm-Mix Asphalt: European Practise, Federal highway Administration, Report No.FHWA-PL-08-007.
21. EN 12697–8:2005. Bituminous mixtures. Test methods for hot mix asphalt. Determination of void characteristics of bituminous specimens.
22. WT-2. Nawierzchnie asfaltowe na drogach krajowych. Część I. Mieszanki mineralno-asfaltowe. Wymagania Techniczne. [Technical Guidelines 2: Asphalt pavements for national roads. Part I: Asphalt mixes]. General Directorate for National Roads and Motorways, Warsaw, 2010.
23. WT-2. Nawierzchnie asfaltowe na drogach krajowych. Część I. Mieszanki mineralno-asfaltowe. Wymagania Techniczne. [Technical Guidelines 2: Asphalt pavements for national roads. Part I: Asphalt mixes]. General Directorate for National Roads and Motorways, Warsaw, 2014.
24. EN 1426:2015 Bitumen and bituminous binders. Determination of needle penetration.
25. J. Judycki, Katalog typowych konstrukcji nawierzchni podatnych i półsztywnych. [Catalogue of typical flexible and semi-rigid pavements]. General Directorate for National Roads and Motorways, Warsaw, 2014.
26. Rheological behavior of n-alkane modified bitumen in aspect of Warm Mix Asphalt technology10.1016/j.conbuildmat.2015.06.033 ↗
27. Laboratory moisture susceptibility evaluation of WMA under possible field conditions10.1016/j.conbuildmat.2015.10.004 ↗
28. EN 1427:2015. Bitumen and bituminous binders. Determination of the softening point. Ring and Ball method.
29. EN 12593:2015. Bitumen and bituminous binders. Determination of the Fraass breaking point.
30. EN 12591:2009. Bitumen and bituminous binders. Specifications for paving grade bitumens.
31. EN-13302:2010. Bitumen and bituminous binders – determination of dynamic viscosity of bituminous binder using a rotating spindle apparatus.
32. D. Sybilski, Ocena odporności na koleinowanie mieszanki mineralno-asfaltowej na podstawie badania zagęszczalności i naprężenia ścinającego w prasie żyratorowej. Sprawozdanie z realizacji tematu TN-230. [Evaluation of rutting resistance of bituminous mixtures based on the tests for compactability and shear stress in the gyratory compactor]. Road and Bridge Research Institute, Warsaw, 2004.
33. P. Jaskula, J. Judycki, Verification of the criteria for evaluation of water and frost resistance of asphalt concrete. Road Mater. Pavement Des. 9(1), 135–162. doi: 10.1080/14680629.2008.9690163.10.1080/14680629.2008.9690163 ↗
34. P. Jaskuła, J. Judycki, Durability of asphalt concrete subjected to deteriorating effects of water and frost. J. Perform. Constr. Facil. 30(1), 2016. doi: 10.1061/(ASCE)CF.1943-5509.0000645.10.1061/(ASCE)CF.1943-5509.0000645 ↗