journal article·2017-08Open access

Evaluation of mortar setting time by using electrical resistivity measurements

Hong Jae Yim, Hanju Lee, Jae Hong Kim

Abstract

Abstract Cement hydration induces microstructural evolution in cement-based materials, causing setting and hardening. Various experimental techniques were proposed to evaluate the time of setting, which includes the Vicat needle test and ultrasound inspections. This study aims to measure electrical resistivity in order to monitor microstructural evolution. For this purpose, an optimized experimental setup is proposed by performing a series of pre-test analyses. A total of 51 mortar mixes are prepared to study the effects of various mix-proportions and the use of various chemical admixtures. As a result, two parameters that represent a change in electrical resistivity are identified: the rising time, which indicates the onset of an increase in electrical resistivity, and the increasing ratio over time. Both parameters are discussed with conventional test results obtained from the penetration resistance method. Their correlation allows us to estimate the setting time of mortar.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Geophysical Methods and Applications · Geophysical and Geoelectrical Methods · Seismic Waves and Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Electrical properties of fluidified Portland cement mixes in the early stage of hydration10.1016/S0008-8846(00)00282-9 ↗
2. Early-age hydration of fresh concrete monitored by non-contact electrical resistivity measurement10.1016/j.cemconres.2007.09.027 ↗
3. Early hydration and setting of Portland cement monitored by IR, SEM and Vicat techniques10.1016/j.cemconres.2009.01.017 ↗
4. Rheological properties of cement pastes: A discussion of structure formation and mechanical property development10.1016/j.cemconres.2008.06.008 ↗
5. Cement hydration: building bridges and dams at the microstructure level10.1617/s11527-006-9147-3 ↗
6. Early-age properties of cement-based materials. i: influence of cement fineness10.1061/(ASCE)0899-1561(2008)20:7(502) ↗
7. ASTM C191-08 · 2008
8. ASTM C403-08 · 2008
9. Water depercolation of setting cement paste evaluated by diffuse ultrasound10.1016/j.cemconcomp.2016.04.003 ↗
10. Mechanical properties of cement pastes and mortars at early ages: evolution with time and degree of hydration
11. Properties of early-age Portland cement mortar monitored with shear wave reflection method
12. Ultrasonic monitoring of setting and hardening of cement mortar – a new device10.1007/BF02480539 ↗
13. H.W. Reinhardt, C.U. Grosse, Advanced Testing of Cement-Based Materials during Setting and Hardening-Final Report of RILEM TC 185-ATC. RILEM Publications SARL 2005.
14. Monitoring the setting of concrete containing blast-furnace slag by measuring the ultrasonic p-wave velocity10.1016/j.cemconres.2008.04.006 ↗
15. Ultrasonic monitoring of the setting of cement-based materials: frequency dependence10.1016/j.conbuildmat.2014.04.128 ↗
16. Percolation of phases in a three-dimensional cement paste microstructural model
17. Three-dimensional computer simulation of Portland cement hydration and microstructure development10.1111/j.1151-2916.1997.tb02785.x ↗
18. Numerical simulation of hydration and microstructural development in hardening cement-based materials (1) theory10.1016/0008-8846(95)00017-8 ↗
19. Microstructure and early-age properties of Portland cement paste – effects of connectivity of solid phases
20. Selection of superplasticizer in concrete mix design by measuring the early electrical resistivities of pastes10.1016/j.cemconcomp.2006.12.015 ↗
21. Effect of treatment temperature on the early hydration characteristics of superplasticized silica fume blended cement pastes10.1016/j.cemconres.2004.06.012 ↗
22. Electrical conductivity based characterization of plain and coarse glass powder modified cement pastes10.1016/j.cemconcomp.2007.05.005 ↗
23. Electrical resistivity and microstructural properties of concrete materials in conditions of current flow10.1016/j.cemconcomp.2008.04.001 ↗
24. Electrical conductivity of setting cement paste with different mineral admixtures10.1016/j.conbuildmat.2011.08.068 ↗
25. Hydration of cement with retarder characterized via electrical resistivity measurements and computer simulation10.1016/j.conbuildmat.2013.11.016 ↗
26. Electrical conductivity of drying cement paste10.1617/s11527-006-9211-z ↗
27. The electrical response characteristics of setting cement paste10.1680/macr.1984.36.126.42 ↗
28. Instantaneous in-situ determination of water-cement ratio of fresh concrete
29. Design and performance of ternary blend high-volume fly ash concretes of moderate slump10.1016/j.conbuildmat.2015.03.082 ↗
30. Prediction of standard compressive strength of cement by the electrical resistivity measurement10.1016/j.conbuildmat.2011.12.111 ↗
31. Neville · 1995
32. ASTM G57 · 2001
33. KS L ISO 679 · 2006