journal article·2019-06

Possibilities and benefits of a new method of modifying conventional building materials with phase-change materials (PCMs)

Michał Ryms, Ewa Klugmann-Radziemska

Publisher page

Abstract

Abstract The paper presents a current study devoted to the optimization of the amount of PCM present within traditional building materials, utilized in this case in hollow-brick walls. Authors focus on proposing an alternative to typical direct addition of PCM to existing building materials: introducing two- and three-component mixtures, based on a porous PCM carrier, which in this case was construction aggregate. Preliminary studies of the possibility of using the aggregate as a carrier, which – due to its porosity and good strength – is well suited for this purpose, were the subject of separate research providing promising results. Three ways of placing PCM in brick openings were proposed and tested: with Micronal DS 5040 X in form of microcapsule powder; with Rubitherm RT22 applied in liquid form, and finally as a porous aggregate impregnated with Rubitherm RT22. The conducted tests were based on measuring cooling time of brick samples prepared in accordance with above variants of PCM placement, which were previously heated by a solar radiation simulator to approx. 30 °C. Results of the experiments showed that the third variant – using aggregate as a PCM carrier, is the most advantageous. In this case, a minimal amount of PCM, which is relatively expensive compared to traditional construction materials, allows achieving cooling time very close to the maximum (100% for PCM without carrier), which effectively extends the stabilization period of room temperature. This way, less expensive solid-liquid PCMs can be utilized instead of Micronal DS 5040 X which is easy to use but relatively expensive due to microencapsulation. Additionally, utilizing Rubitherm RT22 captured in aggregate proved that even a material which is very difficult to apply in construction can be used to increase the energy efficiency of buildings. Similar effect was observed in the study of plaster board samples containing porous construction aggregate soaked in Rubitherm RT22.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Phase Change Materials Research · Solar Thermal and Photovoltaic Systems · Adsorption and Cooling Systems

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. The role of phase change materials for the sustainable energy
2. Thermal conductivity of gypsum with incorporated phase change material (PCM) for building applications
3. Development and thermal characterization of an innovative gypsum-based composite incorporating phase change material as building energy storage system10.1016/j.enbuild.2015.08.002 ↗
4. Application of phase change materials in gypsum boards to meet building energy conservation goals10.1016/j.enbuild.2016.12.046 ↗
5. Review on building energy performance improvement using phase change materials10.1016/j.enbuild.2017.10.066 ↗
6. PCM thermal energy storage in buildings: experimental study and applications10.1016/j.egypro.2015.02.118 ↗
7. Unconventional experimental technologies available for phase change materials (PCM) characterization. Part 1. Thermophysical properties10.1016/j.rser.2014.07.191 ↗
8. Unconventional experimental technologies used for phase change materials (PCM) characterization: part 2 – morphological and structural characterization, physio-chemical stability and mechanical properties10.1016/j.rser.2014.11.051 ↗
9. Effect of the mode and dynamics of thermal processes on DSC-acquired phase-change temperature and latent heat of different kinds of PCM
10. Review on thermal conductivity enhancement, thermal properties and applications of phase change materials in thermal energy storage10.1016/j.rser.2017.10.002 ↗
11. Phase change materials available in the market properties and applications
12. Phase change materials properties, classification, advantages and disadvantages
13. The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces10.1016/j.applthermaleng.2015.02.036 ↗
14. Thermal stabilization and permanent deformation resistance of LWA/PCM-modified asphalt road surfaces10.1016/j.conbuildmat.2017.03.050 ↗
15. Nano-PCMs for enhanced energy storage and passive cooling applications10.1016/j.applthermaleng.2016.03.161 ↗
16. Numerical and experimental investigation of melting and freezing processes in phase change material storage Int10.1016/j.ijthermalsci.2003.07.001 ↗
17. Związki zmiennofazowe w zastosowaniach techniczno-użytkowych i ergonomicznych
18. Thermal performance of heat spreader for electronics cooling with incorporated phase change material10.1016/j.applthermaleng.2011.10.036 ↗
19. Experimental investigation of thermoelectric generator (TEG) with PCM module10.1016/j.applthermaleng.2015.12.005 ↗
20. Thermal performance of building element containing phase change material (PCM) integrated with ventilation system e An experimental study10.1016/j.applthermaleng.2014.05.093 ↗
21. Reasonableness of phase change materials use for air conditioning – a short review, E3S Web of Conferences 14, 01033 (2017)
22. A review on phase change material (PCM) for sustainable passive cooling in building envelopes10.1016/j.rser.2016.03.036 ↗
23. Experimental studies on the applications of PCMs and nano-PCMs in buildings: a critical review10.1016/j.enbuild.2017.08.037 ↗
24. An assessment of mixed type PCM-gypsum and shape-stabilized PCM plates in a building for passive solar heating Sol
25. Thermal storage and nonlinear heat-transfer characteristics of PCM wallboard10.1016/j.enbuild.2008.03.005 ↗
26. A numerical study of external building walls containing phase change materials (PCM)10.1016/j.applthermaleng.2012.02.038 ↗
27. Phase change materials (PCM) for cooling applications in buildings: a review10.1016/j.enbuild.2016.04.006 ↗
28. Phase change material's (PCM) impacts on the energy performance and thermal comfort of buildings in a mild climate10.1016/j.buildenv.2016.01.023 ↗
29. W.M. Lewandowski, M. Ryms, E. Klugmann-Radziemska, H. Denda, P. Wcisło. Stabilizing temperature of asphalt road surface, comprises introducing mixture of asphalt mineral, substructure and/or substrates, and a phase change material comprising mixture of hydrocarbons, preferably ceresin on to the road. Patent Number(s): PL409634-A1, 2016; PL229182-B1, 2018.
30. Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
31. Emissions of volatile and semi-volatile organic compounds and particulate matter from hot asphalts10.1080/09593331808616520 ↗
32. Pungor · 1995
33. The simulation of the thermal behaviour of energetic materials based on DSC and HFC signals10.1007/s10973-007-8864-3 ↗
34. Höhne · 2003
35. Thermophysical properties of the phase change material mixtures – preliminary studies on macromolecular hydrocarbons example
36. Experimental thermal characterization of a Mediterranean residential building with PCM gypsum board walls10.1016/j.buildenv.2012.12.007 ↗
37. Thermal evaluation of laminated composite phase change material gypsum board under dynamic conditions10.1016/j.renene.2015.01.025 ↗
38. Thermal testing and numerical simulation of gypsum wallboards incorporated with different PCMs content10.1016/j.apenergy.2010.08.014 ↗
39. Thermal characterization of gypsum boards with PCM included: Thermal energy storage in buildings through latent heat10.1016/j.enbuild.2012.01.026 ↗
40. Performance evaluation of dual phase change material gypsum board for the reduction of temperature swings in a building prototype in composite climate10.1016/j.enbuild.2017.10.097 ↗
41. An assessment of mixed type PCM-gypsum and shape-stabilized PCM plates in a building for passive solar heating10.1016/j.solener.2007.01.014 ↗
42. Infrared techniques for natural convection investigations in channels between two vertical, parallel, isothermal and symmetrically heated plates10.1016/j.ijheatmasstransfer.2017.06.120 ↗
43. Quantitative study of free convective heat losses from thermodynamic partitions using Thermal Imaging10.1016/j.enbuild.2017.12.047 ↗