Environmentally-friendly ceramic bricks made from zeolite-poor rock and sawdust
Source abstract
Abstract
The production of innovative building bricks from new materials has drawn a huge interest lately, targeting sustainability-related problems. This research investigates the utilization of zeolite-poor rock and sawdust as an alternative for clay to produce new and eco-friendly bricks. Ceramic specimens were prepared using uniaxial dry pressing and firing at a temperature range of (950–1250 °C) for three hours. Sawdust was added as a partial replacement of zeolite-poor rock in the specimens. The replacement percentages were 0%, 2%, 4%, 6%, 8% and 10% by mass of zeolite-poor rock. The raw materials were characterized based on their chemical composition, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray fluorescence (XRF), thermogravimetric (TG), differential thermal analysis (DTA), BET (Brunauer, Emmett and Teller) and particle size distribution. The topographical features, microstructure, phase identification and the characteristic of the produced ceramic bricks were investigated using different characterization techniques such as SEM, EDS and XRD. Moreover, the technical properties (e.g., bulk density, open porosity, volume shrinkage, water absorption, compressive strength and thermal conductivity) of the specimens were also investigated and compared to the control samples' results. The results confirmed that the inclusion of 8% sawdust to zeolite-poor rock minimizes the bulk density of the specimens down to 1.45 from 1.6 g/cm3. It has been noted that their porosity increased up to 37.37 from 31%. In contrast, their compressive strengths declined from 14.5 to 6.7 MPa. However, their strengths were greater than those desired by the standards. The thermal conductivity of the samples contains 8% sawdust reduced from 0.37 to 0.14 W/mK, which corresponds to a decrease of 37% compared to the blank. The mechanical and physical characteristics of bricks were also influenced by the sintering temperature. This research confirms the potential use of zeolite-poor rock together with sawdust as environmentally-friendly building materials.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Recycling and utilization of industrial and municipal waste in materials production · Concrete and Cement Materials Research · Building materials and conservation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (83)
Show source-provided references
1. A.M. Omer, Energy use and environmental impacts: A general review, in Advances in Energy Research, vol. 17, no. 5, Nova Science Publishers, Inc., 2014, pp. 1–38.10.1063/1.3220701 ↗
2. John P. Holdren, et al., Energy, the Environment and Health, New York United Nations Dev. Program., 2018.
3. P.A. Owusu, S. Asumadu-Sarkodie, A review of renewable energy sources, sustainability issues and climate change mitigation, Cogent Engineering, vol. 3, no. 1. Cogent OA, p. 1167990, Dec. 31, 2016, https://dx.doi.org/10.1080/23311916.2016.1167990.10.1080/23311916.2016.1167990 ↗
4. Energy sustainability: A pragmatic approach and illustrations10.3390/su1010055 ↗
5. Characteristics of heat insulating clay bricks made from zeolite, waste steel slag and expanded perlite10.1016/j.ceramint.2018.01.175 ↗
6. Building energy-consumption status worldwide and the state-of-the-art technologies for zero-energy buildings during the past decade10.1016/j.enbuild.2016.06.089 ↗
7. Energy efficiency trends and policies in the household and tertiary sectors; an analysis based on the ODYSSEE and MURE databases
8. Fernando Pacheco-Torgal, et al., Handbook of Alkali-Activated Cements, Mortars and Concretes - 1st Edition, Elsevier, 2014.10.1533/9781782422884.1 ↗
9. Thomas B. Johansson, et al., Global Energy Assessment [mdash] Toward a Sustainable Future. pp. 1203–1306, 2012.
10. Buildings and Climate Change Summary for Decision Makers Sustainable Buildings & Climate Initiative.
11. Using passive cooling strategies to improve thermal performance and reduce energy consumption of residential buildings in U.A.E. buildings10.1016/j.foar.2014.01.002 ↗
12. Intelligent Buildings: An Introduction - 1st Edition - Derek Clements, 2013.
13. The impact of thermal mass on building energy consumption10.1016/j.apenergy.2017.04.024 ↗
14. EN 832:1998, Thermal performance of buildings - Calculation of energy use for heating - Residential, 1998.
15. Porous clay bricks manufactured with rice husks10.1016/j.conbuildmat.2012.09.110 ↗
16. The use of different forms of waste in the manufacture of ceramic bricks10.1016/j.clay.2011.03.003 ↗
17. The use of recycled paper processing residues in making porous brick with reduced thermal conductivity10.1016/j.ceramint.2009.02.027 ↗
18. Characterization of ceramic bricks incorporated with textile laundry sludge10.1016/j.ceramint.2011.08.015 ↗
19. L.A. Gömze, E. Kurovics, L.N. Gömze, Changing the rheo-mechanical models of light metal Ti and Ti-alloy powders under uniaxial compaction, J. Phys. Conf. Ser., vol. 1045, no. 1, 2018, https://dx.doi.org/10.1088/1742-6596/1045/1/012001.10.1088/1742-6596/1045/1/012001 ↗
20. Influence of raw materials composition on firing shrinkage, porosity, heat conductivity and microstructure of ceramic tiles
21. A.S. More, A. Tarade, A. Anant, Assessment of suitability of Fly Ash and Rice Husk Ash burnt clay bricks, 2014.
22. A.P. and D. B. Garud, Engineering properties of clay bricks with use of fly ash by IJRET Editor - issuu, 2014.10.15623/ijret.2014.0321016 ↗
23. E. Kurovics, S.N. Kulkov, L.A. Gömze, Investigation of ceramic brick rods with blackened materials inside, Epa. - J. Silic. Based Compos. Mater., vol. 70, no. 1, pp. 3–7, 2018, https://dx.doi.org/10.14382/epitoanyag-jsbcm.2018.1.10.14382/epitoanyag-jsbcm.2018.1 ↗
24. Preparation of eco-friendly construction bricks from hematite tailings10.1016/j.conbuildmat.2010.11.025 ↗
25. Effect of mechanical treatment on the structure and properties of natural zeolite10.1134/S2075113318050040 ↗
26. A review of the chemistry, structure, properties and applications of zeolites
27. Y. Li, L. Li, J. Yu, Applications of zeolites in sustainable chemistry, Chem, vol. 3, no. 6. Elsevier Inc, pp. 928–949, Dec. 14, 2017, https://dx.doi.org/10.1016/j.chempr.2017.10.009.10.1016/j.chempr.2017.10.009 ↗
28. Structuring adsorbents and catalysts by processing of porous powders10.1016/j.jeurceramsoc.2014.01.008 ↗
29. O.B. Kotova et al., Composite materials based on zeolite-montmorillonite rocks and aluminosilicate wastes, Epa. - J. Silic. Based Compos. Mater., vol. 71, no. 4, pp. 125–130, 2019, https://dx.doi.org/10.14382/epitoanyag-jsbcm.2019.22.10.14382/epitoanyag-jsbcm.2019.22 ↗
30. Clay- and zeolite-based biogeosorbents: modelling and properties
31. Adsorption and catalytic properties of sedimentary clinoptilolite and mordenite from the Tokaj Hills, Hungary10.1016/S0144-2449(82)80034-1 ↗
32. L.K. Kazantseva, T.S. Yusupov, T.Z. Lygina, L.G. Shumskaya, D.S. Tsyplakov, Foam glass from mechanoactivated zeolite-poor rock, Glas. Ceram. (English Transl. Steklo i Keramika), vol. 70, no. 9–10, pp. 360–364, Jan. 2014, https://dx.doi.org/10.1007/s10717-014-9580-7.10.1007/s10717-014-9580-7 ↗
33. G. Marcari, G. Fabbrocino, P.B. Lourenço, Investigation on compressive behaviour of Tuff masonry panels.
34. R.H. Price, Analysis of the rock mechanics properties of volcanic tuff units from Yucca Mountain, Nevada Test Site, No. SAND-82-1315. 1983.10.2172/59506 ↗
35. N. Tangboriboon, S. Moonsri, A. Netthip, A. Sirivat, Innovation of Embedding Eggshell to Enhance Physical-Mechanical-Thermal Properties in Fired Clay Bricks via Extrusion Process, in MATEC Web of Conferences, Oct. 2016, vol. 78, p. 01003, https://dx.doi.org/10.1051/matecconf/20167801003.10.1051/matecconf/20167801003 ↗
36. A practical proposal for solving the world's cigarette butt problem: Recycling in fired clay bricks10.1016/j.wasman.2016.03.012 ↗
37. Recycling of cigarette butts in fired clay bricks: A new laboratory investigation10.3390/ma13030790 ↗
38. G. Thalmaier et al., Influence of sawdust particle size on fired clay brick properties, Mater. Constr., vol. 70, no. 338, 2020, https://dx.doi.org/10.3989/MC.2020.04219.10.3989/mc.2020.04219 ↗
39. A Comparison of thermal and mechanical properties of clay bricks prepared with three different pore-forming additives: Vermiculite, wood ash, and sawdust10.1002/ep.13150 ↗
40. Reuse of sugarcane bagasse ash to produce a lightweight aggregate using microwave oven sintering10.1016/j.conbuildmat.2019.06.150 ↗
41. Recycling of sugarcane bagasse ash waste in the production of clay bricks10.1016/j.jenvman.2012.01.032 ↗
42. Recycling untreated sugarcane bagasse ash and industrial wastes for the preparation of resistant, lightweight and ecological fired bricks10.1016/j.conbuildmat.2019.117314 ↗
43. A proposal for recycling theworld's unused stockpiles of treated wastewater sludge (biosolids) in fired-clay bricks10.3390/buildings9010014 ↗
44. Thermal conductivity of fired clays: Effects of mineralogical and physical properties of the raw materials10.1016/j.clay.2010.06.002 ↗
45. Effective thermal conductivity of partially saturated porous rocks10.1016/j.ijsolstr.2006.05.023 ↗
46. Q. Sun, S. E. Chen, Q. Gao, W. Zhang, J. Geng, Y. Zhang, Analyses of the factors influencing sandstone thermal conductivity, Acta Geodyn. Geomater., vol. 14, no. 2, pp. 173–180, 2017, https://dx.doi.org/10.13168/AGG.2017.0001.10.13168/AGG.2017.0001 ↗
47. László A. Gömze, Applied Material Science I. Compilation of Selected Scientific Papers, no. September. 2016.
48. A. Erker, Thermal conductivity of the brick ceramic body. 2002.
49. L.A. Gömze, L.N. Gömze, E. Kurovics, G. Benedek, Conventional brick clays as a challenge of materials science - New explanation of drying sensitivities, IOP Conf. Ser. Mater. Sci. Eng., vol. 613, no. 1, 2019, https://dx.doi.org/10.1088/1757-899X/613/1/012005.10.1088/1757-899X/613/1/012005 ↗
50. M.N. Rahaman, Ceramic Processing and Sintering. 2003.
51. Influence of compacting times and pressures on rheological properties of alumina and quartz ceramic powder mixtures
52. Examination of ancient pottery using the scanning electron microscope10.1038/257122a0 ↗
53. The influence of composition, microstructure and firing temperature on the density, porosity, and shrinkage of new zeolite-alumina composite material
54. A. C20-00, Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes.
55. A. C67-12, Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile, ASTM International, West Conshohocken, PA, USA, 2009.
56. A. C20-00, Standard Test Method for Particle-Size Analysis of Soils, West Conshohocken, 2007.
57. H. Zhao, J.H. Kwak, Z. Conrad Zhang, H.M. Brown, B.W. Arey, J.E. Holladay, Studying cellulose fiber structure by SEM, XRD, NMR and acid hydrolysis, Carbohydr. Polym., vol. 68, no. 2, pp. 235–241, Mar. 2007, https://dx.doi.org/10.1016/j.carbpol.2006.12.013.10.1016/j.carbpol.2006.12.013 ↗
58. P. Lu, Y. Lo Hsieh, Preparation and properties of cellulose nanocrystals: Rods, spheres, and network, Carbohydr. Polym., vol. 82, no. 2, pp. 329–336, Sep. 2010, https://dx.doi.org/10.1016/j.carbpol.2010.04.073.10.1016/j.carbpol.2010.04.073 ↗
59. Sono-chemical synthesis of cellulose nanocrystals from wood sawdust using Acid hydrolysis10.1016/j.ijbiomac.2017.10.028 ↗
60. Ceramic bricks containing Ni ions from contaminated biomass used as an adsorbent10.1186/s42834-020-00067-3 ↗
61. Z. Zhang, Y.C. Wong, A. Arulrajah, S. Horpibulsuk, A review of studies on bricks using alternative materials and approaches, Construction and Building Materials, vol. 188. Elsevier Ltd, pp. 1101–1118, Nov. 10, 2018, https://dx.doi.org/10.1016/j.conbuildmat.2018.08.152.10.1016/j.conbuildmat.2018.08.152 ↗
62. Prehistoric schistosomiasis parasite found in the Middle East10.1016/S1473-3099(14)70794-7 ↗
63. Characteristics of acid resisting bricks made from quarry residues and waste steel slag10.1016/j.conbuildmat.2007.04.007 ↗
64. J.-E.F.M. Ibrahim et al., Effect of composition and sintering temperature on thermal properties of Zeolite-Alumina Composite Materials, Epa. J. Silic. Based Compos. Mater., vol. 72, no. 4, pp. 131–134, 2020, https://dx.doi.org/10.14382/epitoanyag-jsbcm.2020.21.10.14382/epitoanyag-jsbcm.2020.21 ↗
65. Use of ceramic waste powder for manufacturing durable and eco-friendly bricks10.1007/s42107-019-00205-2 ↗
66. Energy savings, thermal conductivity, micro and macro structural analysis of fired clay bricks incorporating cigarette butts10.1016/j.conbuildmat.2021.122755 ↗
67. Combined effects of paper mill sludge and carbonation sludge on characteristics of fired clay bricks10.1016/j.conbuildmat.2020.118722 ↗
68. Potential pathway for recycling of the paper mill sludge compost for brick making10.1016/j.conbuildmat.2021.122384 ↗
69. Cost-effective utilization of mineral-based raw materials for preparation of porous mullite ceramic membranes via in-situ reaction method
70. Novel hollow alumina sphere-based ceramic bonded by in situ mullite whisker framework
71. Preparation and thermal shock resistance of corundum-mullite composite ceramics from andalusite
72. Effect of in-situ formation of columnar mullite and pore structure refinement on high temperature properties of corundum casatbles
73. Mullite whisker network reinforced ceramic with high strength and lightweight10.1016/j.jallcom.2017.09.150 ↗
74. Fabrication, microstructure, and properties of fired clay bricks using construction and demolition waste sludge as the main additive10.1016/j.jclepro.2020.120733 ↗
75. C.W. Tang, Properties of fired bricks incorporating TFT-LCD waste glass powder with reservoir sediments, Sustainability, vol. 10, no. 7, 2018, https://dx.doi.org/10.3390/su10072503.10.3390/su10072503 ↗
76. An investigation on use of paper mill sludge in brick manufacturing10.1016/j.conbuildmat.2017.05.087 ↗
77. Preparation of porous brick from diatomite and sugar filter mud at lower temperature10.1016/j.conbuildmat.2017.09.021 ↗
78. Characteristics of porous ceramics produced from waste diatomite and water purification sludge10.1089/ees.2010.0340 ↗
79. The production of porous brick material from diatomaceous earth and Brazil nut shell ash10.1016/j.conbuildmat.2015.08.003 ↗
80. Preparation and mechanism of the sintered bricks produced from Yellow River silt and red mud10.1016/j.jhazmat.2011.11.095 ↗
81. Characteristics of the fired bricks with low-silicon iron tailings10.1016/j.conbuildmat.2014.07.075 ↗
82. Mechanism analysis of pore structure and crystalline phase of thermal insulation bricks with high municipal sewage sludge content10.1016/j.conbuildmat.2020.120021 ↗
83. Feasibility of using paper pulp residues into fired clay bricks10.1016/j.jclepro.2020.121464 ↗