journal article·2016-12

Influence of substrate texture on the tensile and shear bond strength of rendering mortars

Carina M. Stolz, Angela B. Masuero, Daniel T. Pagnussat, Ana Paula Kirchheim

Publisher page

Abstract

Abstract This study assessed the influence of the substrate texture and rheological characteristics of mortars on the shear and tensile bond strength of rendering mortars. Concrete slabs with three different types of surface textures were used as substrate. Rendering mortars were prepared with a composition of 1:1:4 (cement: hydrated lime: dry sand, in volume – converted to mass), water/binder ratio 1.2, with different concentrations of an air-entraining admixture (0, 0.2 and 0.5%), and sand with a controlled granulometric composition, to modify the rheological properties of this material. These mortars were placed on the substrates using a device to control the force of application. The results showed that increasing the contact area in the substrate, as a result of different surface textures, does not always increase the bonding strength between the substrate and the render. Instead, the rheology of the rendering mortars seems to be the main factor controlling their bonding capacity. Depending on the substrate texture, rendering mortars with different consistencies increase the bonding strength of this type of systems. Also the workability of the rendering mortars, considering the roughness of the substrate, needs to be optimized to ensure a long-lasting life of the rendering.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovations in Concrete and Construction Materials · Building materials and conservation · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Water movement in porous building materials – I. Unsaturated flow theory and its applications10.1016/0360-1323(77)90040-3 ↗
2. Water movement in porous building materials – IX. The water absorption and sorptivity of concretes10.1016/0360-1323(87)90044-8 ↗
3. H.O. Sugo, A.W. Page, S.J. Lawrence, The development of mortar/unit bond, in: Canadian Masonry Symposium, 9th, Fredericton. Proceedings… Department of Civil Engineering – University of New Brunswick, 2001.
4. The importance of the porosity of mortars, tiles and bricks in relation to their bonding strengths
5. Reliability of the pull-off test in situ evaluation of adhesion strength10.1016/j.conbuildmat.2011.12.097 ↗
6. A bond tensile strength test for use in assessing the compatibility of brick/mortar interfaces10.1016/0950-0618(90)90001-H ↗
7. Bond between 19th Century lime mortars and glazed ceramic tiles10.1016/j.conbuildmat.2014.02.043 ↗
8. Characterisation of thin layer polymer cement mortared concrete masonry bond10.1016/j.conbuildmat.2014.12.098 ↗
9. H. Carasek, Portland cement mortars adherence to porous substrates: assessing of the influence factors and contribution to the study of the adension mechanism. 1996. 285 p. Phd thesis (PhD in Civil Engineering) – Polytechnic School of São Paulo University, São Paulo (In Portuguese).
10. S.R.C. Gonçalves, Variability and dispersion factors of bond strength in mortar coatings – case study. 2004. 148 p. Dissertation (Master in Civil Engineering) – University of Brasilia, Brasilia (In Portuguese).
11. L. Courard, Contribution to the analysis of the parameters affecting the creation of an interface between the concrete and the repair system. Palatability and adhesion: a cause and effect link. Phd thesis, University of Liege, Department Argenco, Liège (In French), 1998.
12. J.V. Romero, Adhesion to concrete of different chemical bases mortars. 2010. 367p. Phd Thesis (Ph.D. in Civil Engineering) – Polytechnic University of Madrid, Madrid (In Spanish).
13. H. Carasek, J.G. Djanikian, Portland Cement Mortars Adherence to Masonry Surfaces Units. Technical Bulletin BT/PCC/179 Polytechnic School of USP. São Paulo, 1997 (In Portuguese).
14. M.E.J. Pretto, Influence of the rugosity produced by concrete substrate treatment in adherence of mortar coverings. 2007. 180 p. Thesis (Master) – Federal University of Rio Grande do Sul, Porto Alegre (In Portuguese).
15. P.F.G. Banfill, The rheology of fresh cement and concrete – a review, in: 11o International Congress on Cement Chemistry, 2003, Duban. Proceedings. Duban, 2003.
16. Study of the laboratory Vane test on mortars10.1016/j.buildenv.2005.08.016 ↗
17. Effect of various superplasticizers on rheological properties of cement paste and mortars10.1016/0008-8846(94)90055-8 ↗
18. Mortar composition defined according to the rheometer and flow table tests using factorial designed experiments10.1016/j.conbuildmat.2009.06.028 ↗
19. Effect of moisture exchange on interface formation in the repair system studied by X-ray absorption10.3390/ma9010002 ↗
20. Analysis of main parameters affecting substrate/mortar contact area through tridimensional laser scanner10.1016/j.jcis.2015.05.028 ↗
21. P. Helene, P.R. Terzian, Manual Dosing and Control of Concrete. São Paulo: PINI, 1992. 350 p. (In Portuguese).
22. Rheological behavior of mortars under different squeezing rates10.1016/j.cemconres.2009.05.014 ↗
23. C.M. Stolz, Interaction between mortar rheological parameters and surface potential contact area on mortar renderings bond strength. 2011. 212 p. Thesis (Master) – Federal University of Rio Grande do Sul, Porto Alegre (In Portuguese).
24. M.C. Candia, Contribution to the study of the basis preparation techniques on the performance of mortar coatings. 1998. 198 p. Thesis (PhD) –São Paulo University, São Paulo (In Portuguese).
25. E. Bauer, Mortar coatings – characteristics and peculiarities. Brasília: LEM-UnB; Sinduscon, 2005. 92 p (In Portuguese).
26. N.J.D. Alves, Assessment of air entrained admixtures in mortars coatings. 2002. 199 f. Thesis (Master) – Brasília University, Brasília (In Portuguese).
27. Bond