journal article·2021-05

Multiscale study of fibre orientation effect on pullout and tensile behavior of steel fibre reinforced concrete

Le Chen, Weiwei Sun, Bingcheng Chen, Ze Shi, Jianzhong Lai, Jun Feng

Publisher page

Abstract

Abstract The tensile response of steel fibre reinforced concrete (SFRC) placed in a given structural element is strongly dependent on the final fibre distribution and orientation with respect to the load direction. In this work, fibre orientation effect was investigated in multi-scale through double-sided inclined fibre pullout test and SFRC dogbone specimen tension test. A numerical model based on Lattice Discrete Particle Model-Fibre (LDPM-F) was developed considering fibre bridging effect by modelling individual fibre, randomly placed within the matrix according to the given fibre volume fraction. The SFRC numerical model validation was achieved by well predicting the mechanical response as well as the failure pattern of SFRC under tension. Both fibre pullout test and SFRC tension test revealed that the fibre inclined angle with respect to tensile load, increasing from 0° to 60°, leads to greater ductility. Lower fibre content SFRC with oriented fibres showed greater energy absorption capacity than SFRC with higher fibre content. Relevance of fibre orientation for bond-slippage behavior and tensile properties of SFRC was highlighted. This fibre orientation control concept may promote the material development of cost effective but performance superior SFRC.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Advanced ceramic materials synthesis · Innovations in Concrete and Construction Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (73)

Show source-provided references
1. Effect of high-rate dynamic comminution on penetration of projectiles of various velocities and impact angles into concrete10.1007/s10704-019-00354-0 ↗
2. Multi-layered two stage fibrous composites against low-velocity falling mass and projectile impact10.1016/j.conbuildmat.2020.118631 ↗
3. Influence of hybrid fiber reinforcement on mechanical properties and autogenous shrinkage of an ecological uhpfrcc10.1061/(ASCE)MT.1943-5533.0002650 ↗
4. Effect of weight and drop height of hammer on the flexural impact performance of fiber-reinforced concrete10.1016/j.conbuildmat.2017.02.098 ↗
5. Intrinsic effect of hybrid fibres 3d network on the electrochemical characteristics of ultra-high performance fibre reinforced composites (uhpfrc)10.1016/j.cemconcomp.2020.103818 ↗
6. Low-velocity impact of hot-pressed pva fiber-reinforced alkali-activated stone wool composites10.1016/j.cemconcomp.2020.103805 ↗
7. Experimental study on engineering properties of concrete reinforced with hybrid recycled tyre steel and polypropylene fibres
8. Optimization of fiber volume fraction to enhance reinforcing efficiency in hybrid fiber reinforced strain hardening cementitious composite10.1016/j.cemconcomp.2020.103704 ↗
9. Effects of fiber shape and distance on the pullout behavior of steel fibers embedded in ultra-high-performance concrete10.1016/j.cemconcomp.2019.05.006 ↗
10. Mechanical analyses of hooked fiber pullout performance in ultra-high-performance concrete10.1016/j.conbuildmat.2014.07.049 ↗
11. Bonding mechanisms and strength of steel fiber–reinforced cementitious composites: overview10.1061/(ASCE)MT.1943-5533.0002154 ↗
12. Fracture behaviour of hybrid fibre-reinforced roller-compacted concrete used in pavements
13. Bond stress model for fiber reinforced concrete based on bond stress-slip relationship
14. Influence of fiber mixture on impact response of ultra-high-performance hybrid fiber reinforced cementitious composite10.1016/j.compositesb.2018.12.141 ↗
15. Experimental investigation of mode i fracture features of steel fiber-reinforced reactive powder concrete using semi-circular bend test10.1016/j.engfracmech.2019.01.029 ↗
16. Polyolefin fiber-reinforced concrete enhanced with steel-hooked fibers in low proportions10.1016/j.matdes.2014.03.050 ↗
17. Experimental tests and reliability analysis of the cracking impact resistance of uhpfrc10.3390/fib8120074 ↗
18. Spacing and bundling effects on rate-dependent pullout behavior of various steel fibers embedded in ultra-high-performance concrete10.1007/s43452-020-00048-8 ↗
19. Numerical and analytical modeling of fiber-matrix bond behaviors of high performance cement composite10.1016/j.cemconres.2019.105892 ↗
20. T. Ng, T. Htut, S. Foster, Fracture of steel fibre reinforced concrete–the unified variable engagement model, UNICIV Report R-460, School of Civil and Environmental Engineering, The University of New South Wales, Sydney.
21. An approach to investigate the fiber-cementitious composites bond-slip mechanisms10.1520/ACEM20190054 ↗
22. Mechanical behavior of hybrid steel-fiber self-consolidating concrete: materials and structural aspects10.1016/j.matdes.2013.08.014 ↗
23. Hybrid effect of macro and micro steel fibers on the pullout and tensile behaviors of ultra-high-performance concrete10.1016/j.compositesb.2018.11.026 ↗
24. Using calcium carbonate whisker in hybrid fiber-reinforced cementitious composites10.1061/(ASCE)MT.1943-5533.0001041 ↗
25. Effects of silica additives on fracture properties of carbon nanotube and carbon fiber reinforced portland cement mortar10.1016/j.cemconcomp.2014.08.005 ↗
26. Surface roughness effects on the reinforcement of cement mortars through 3d printed metallic fibers10.1016/j.compositesb.2016.05.055 ↗
27. Effects of brass coating and nano-sio2 coating on steel fibermatrix interfacial properties of cement-based composite10.1016/j.compositesb.2020.107904 ↗
28. Experimental, analytical and numerical analysis of the pullout behaviour of steel fibres considering different fibre types, inclinations and concrete strengths10.1002/suco.201300058 ↗
29. Effect of steel fibres on mechanical properties of high-strength concrete10.1016/j.matdes.2009.11.025 ↗
30. Computational investigation of twisted fiber pullout from ultra-high performance concrete10.1016/j.conbuildmat.2019.06.146 ↗
31. Marković · 2006
32. Effect of matrix strength on pullout behavior of steel fiber reinforced very-high strength concrete composites10.1016/j.conbuildmat.2010.06.059 ↗
33. Pull-out behavior of steel fiber embedded in flowable rpc and ordinary mortar10.1016/j.conbuildmat.2014.11.037 ↗
34. A review on additive manufacturing of polymer-fiber composites10.1016/j.compstruct.2017.08.088 ↗
35. Effects of transition zone densification on fiber/cement paste bond strength improvement10.1016/S1065-7355(97)90010-9 ↗
36. Effect of mineral admixtures and steel fiber volume contents on the behavior of high performance fiber reinforced concrete10.1016/j.matdes.2014.06.066 ↗
37. N. Banthia, J. Trottier, Concrete reinforced with deformed steel fibers, Part 1 (1994) 435–446
38. Fiber orientation distribution and tensile mechanical response in uhpfrc10.1617/s11527-016-0914-5 ↗
39. Pullout behavior of straight and hooked-end steel fibers in uhpc matrix with various embedded angles10.1016/j.conbuildmat.2018.10.067 ↗
40. The effect of fibre distribution characteristics on the flexural strength of steelfibre-reinforced ultra high strength concrete10.1016/j.conbuildmat.2010.11.057 ↗
41. Relationship between fiber orientation/distribution and post-cracking behaviour in ultra-high-performance fiber-reinforced concrete (uhpfrc)10.1016/j.cemconcomp.2017.07.007 ↗
42. Non-destructive assessment of fibre content and orientation in uhpfrc layers based on a magnetic method10.1016/j.cemconcomp.2016.05.024 ↗
43. Bond-slip mechanisms of steel fibers in concrete
44. K. Wille, A.E. Naaman, Pullout behavior of high-strength steel fibers embedded in ultra-high-performance concrete, ACI Mater. J. 109 (4).
45. Blast-resistant performance of hybrid fiber-reinforced concrete (hfrc) panels subjected to contact detonation
46. Pullout of inclined flexible fiber in cementitious composite
47. Evaluation of shrinkage induced cracking performance of low shrinkage engineered cementitious composite by ring tests10.1016/j.compositesb.2013.03.012 ↗
48. Susceptibility of portland cement and blended cement concretes to plastic shrinkage cracking10.1016/j.cemconcomp.2017.10.002 ↗
49. Experimental test methods to determine the uniaxial tensile and compressive behaviour of ultra high performance fibre reinforced concrete (uhpfrc)10.1016/j.conbuildmat.2012.04.030 ↗
50. Effect of mechanical clamping on the pullout response of hooked steel fibers embedded in cementitious matrices
51. Lattice discrete particle model for fiber-reinforced concrete. i: Theory
52. Lattice discrete particle model (ldpm) for failure behavior of concrete. i: Theory10.1016/j.cemconcomp.2011.02.011 ↗
53. Discrete element framework for modeling tertiary creep of concrete in tension and compression10.1016/j.engfracmech.2018.07.006 ↗
54. Asymptotic expansion homogenization of discrete fine-scale models with rotational degrees of freedom for the simulation of quasi-brittle materials10.1016/j.jmps.2016.01.001 ↗
55. Multiphysics lattice discrete particle model for the simulation of concrete thermal spalling10.1016/j.cemconcomp.2019.103457 ↗
56. Thick plain concrete targets subjected to high speed penetration of 30crmnsini2a steel projectiles: tests and analyses10.1016/j.ijimpeng.2018.09.005 ↗
57. Lattice discrete particle modeling of fiber reinforced concrete: Experiments and simulations10.1016/j.euromechsol.2015.12.002 ↗
58. A novel material for in situ construction on mars: experiments and numerical simulations10.1016/j.conbuildmat.2016.05.046 ↗
59. L. Han, M. Pathirage, A.-T. Akono, G. Cusatis, Lattice discrete particle modeling of size effect in slab scratch tests, J. Appl. Mech. 88 (2).10.1115/1.4048989 ↗
60. A stereological approach to roughness of fracture surfaces and tortuosity of transport paths in concrete10.1016/S0958-9465(00)00018-4 ↗
61. Discontinuous cell method (dcm) for the simulation of cohesive fracture and fragmentation of continuous media10.1016/j.engfracmech.2016.11.026 ↗
62. Use of high volumes of fly ash to improve ecc mechanical properties and material greenness
63. Z. Lin, T. Kanda, V.C. Li, On interface property characterization and performance of fiber reinforced cementitious composites.
64. An armour-piercing projectile penetration in a double-layered target of ultra-high-performance fiber reinforced concrete and armour steel: experimental and numerical analyses10.1016/j.matdes.2016.04.021 ↗
65. Crack-bridging force in random ductile fiber brittle matrix composites
66. Fiber-bridging constitutive law of engineered cementitious composites10.3151/jact.6.181 ↗
67. Numerical study on the hard projectile perforation on rc panels with ldpm10.1016/j.conbuildmat.2018.06.020 ↗
68. Influence of aggregate and curing regime on the mechanical properties of ultra-high performance fibre reinforced concrete (uhpfrc)10.1016/j.conbuildmat.2008.11.012 ↗
69. Microscopic reinforcement for cement based composite materials10.1016/j.conbuildmat.2012.10.012 ↗
70. Practical design criteria for saturated pseudo strain hardening behavior in ecc10.3151/jact.4.59 ↗
71. Terminal ballistic and static impactive loading on thick concrete target10.1016/j.conbuildmat.2020.118899 ↗
72. A performance versus cost analysis of prepreg carbon fibre epoxy energy absorption structures10.1016/j.compstruct.2015.01.022 ↗
73. Lattice discrete particle model for fiber-reinforced concrete. ii: Tensile fracture and multiaxial loading behavior