Engineering performance of sustainable geopolymer foamed and non-foamed concretes
Source abstract
Abstract
Abstract This study investigates the effect of using palm oil fuel ash (POFA) as a partial replacement for fly ash (FA) in lightweight geopolymer foamed concrete and geopolymer mortar. Three different proportions of POFA contents of 10%, 20%, and 30% with a target fresh density of about 1300 ± 50 kg/m3, were used. The development of compressive strength and splitting tensile strength were investigated over a 28-day curing period. Transport properties, in terms of water absorption, porosity, and sorptivity, were also investigated. Microstructural characteristics through XRD, SEM and EDX were also investigated and reported. The results found that the compressive strength of geopolymer foamed concrete, with up to 30% POFA, was higher than the control; however, for the POFA-based geopolymer mortar, the compressive strength reduced with increasing POFA content. The highest compressive strength of 6.1 MPa was recorded in the geopolymer foamed concrete with 20% POFA, whereas the control mix of geopolymer mortar produced 36.6 MPa. The geopolymer foamed concrete achieved 70% of its 28-day compressive strength within 3 days. The oven-dry density of the geopolymer foamed concrete ranged from 1193-1344 kg/m3. The ultrasonic pulse velocity (UPV) value was 1.5 km/s for the geopolymer foamed concrete while the geopolymer mortar had the range of 2.2–2.4 km/s. In general, the transport properties were mostly dependent on the oven-dry density of the geopolymer foamed concrete. The POFA content of 20% was found to provide the required silica and alumina to produce geopolymerization gel. Further, the SEM images showed unreacted FA particles that led to an increase in the voids. Furthermore, the XRD patterns showed the addition of foam affected the intensity of the peaks.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Magnesium Oxide Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (84)
Show source-provided references
1. P.-C. Aı̈tcin, Cements of yesterday and today: concrete of tomorrow, Cem. Concr. Res., 2000. 30(9): 1349–1359.10.1016/S0008-8846(00)00365-3 ↗
2. Amplified CO2 reduction of greenhouse gas emissions with C2CNT carbon nanotube composites
3. Recycling of geopolymer concrete10.1016/j.conbuildmat.2015.10.037 ↗
4. Sustainable Buildings & Climate Initiative, Buildings and climate change: summary for decisions-makers, United Nations Environment Programme. 2009, France.
5. Toward green concrete for better sustainable environment10.1016/j.proeng.2014.12.190 ↗
6. Supplementary cementitious materials origin from agricultural wastes – a review10.1016/j.conbuildmat.2014.10.010 ↗
7. Durability properties of sustainable concrete containing high volume palm oil waste materials10.1016/j.jclepro.2016.07.061 ↗
8. Performance evaluation of palm oil clinker as coarse aggregate in high strength lightweight concrete10.1016/j.jclepro.2015.08.043 ↗
9. Response of oil palm shell concrete slabs subjected to quasi-static and blast loads10.1016/j.conbuildmat.2016.04.103 ↗
10. Miura · 2001
11. Microstructural investigations of palm oil fuel ash and fly ash based binders in lightweight aggregate foamed geopolymer concrete10.1016/j.conbuildmat.2016.05.076 ↗
12. Effect of aggregate size and proportion on strength properties of palm kernel shell concrete
13. Assessing some durability properties of sustainable lightweight oil palm shell concrete incorporating slag and manufactured sand10.1016/j.jclepro.2015.06.122 ↗
14. Chemistry of geopolymeric systems, terminology
15. Influence of rice husk ash on mechanical properties and fire resistance of recycled aggregate high-calcium fly ash geopolymer concrete10.1016/j.jclepro.2019.119797 ↗
16. Effects of source materials, fineness and curing methods on the strength development of alkali-activated binder
17. Correlation between pore structure, compressive strength and thermal conductivity of porous metakaolin geopolymer10.1016/j.conbuildmat.2020.118641 ↗
18. Comparison of strength and durability characteristics of a geopolymer produced from fly ash, ground glass fiber and glass powder10.3989/mc.2017.05416 ↗
19. Strength development in clay–fly ash geopolymer10.1016/j.conbuildmat.2012.11.015 ↗
20. Eco-friendly approach to enhance the mechanical performance of geopolymer foams: Using glass fibre waste coming from wind blade production10.1016/j.conbuildmat.2019.117805 ↗
21. Engineering properties and fracture behaviour of high volume palm oil fuel ash based fibre reinforced geopolymer concrete10.1016/j.conbuildmat.2016.02.022 ↗
22. Assessment on engineering properties and CO2 emissions of recycled aggregate concrete incorporating waste products as supplements to Portland cement10.1016/j.jclepro.2018.08.292 ↗
23. Experimental investigation on the properties of lightweight concrete containing waste oil palm shell aggregate10.1016/j.proeng.2015.11.065 ↗
24. A comparison of the thermal conductivity of oil palm shell foamed concrete with conventional materials10.1016/j.matdes.2013.04.078 ↗
25. Evaluation of thermal conductivity, mechanical and transport properties of lightweight aggregate foamed geopolymer concrete10.1016/j.enbuild.2013.12.029 ↗
26. Utilization of palm oil fuel ash as binder in lightweight oil palm shell geopolymer concrete
27. B.G. Hellers, B.R. Schmidt, Autoclaved aerated concrete (AAC)-the story of a low-weight material, in: 5th International Conference on Autoclaved Aerated Concrete 2012). 2011.
28. Pore characteristics in one-part mix geopolymers foamed by H 2 O 2: The impact of mix design10.1016/j.matdes.2017.05.084 ↗
29. A comparison between different foaming methods for the synthesis of light weight geopolymers10.1016/j.ceramint.2014.05.108 ↗
30. Geopolymer foams by gelcasting10.1016/j.ceramint.2013.11.011 ↗
31. Mix design, properties and cost analysis of fly ash-based geopolymer foam10.1016/j.conbuildmat.2015.01.063 ↗
32. Geopolymer foam concrete: an emerging material for sustainable construction10.1016/j.conbuildmat.2014.01.081 ↗
33. Geopolymer-based hybrid foams: lightweight materials from a sustainable production process10.1016/j.jclepro.2019.119588 ↗
34. High-porosity geopolymer foams with tailored porosity for thermal insulation and wastewater treatment10.1557/jmr.2017.127 ↗
35. The pore characteristics of geopolymer foam concrete and their impact on the compressive strength and modulus10.3389/fmats.2016.00038 ↗
36. Fresh and hardened properties of lightweight foamed concrete with palm oil fuel ash as filler10.1016/j.conbuildmat.2013.04.015 ↗
37. Use of waste ash from palm oil industry in concrete10.1016/j.wasman.2005.12.014 ↗
38. Assessing the effect of biomass ashes with different finenesses on the compressive strength of blended cement paste10.1016/j.matdes.2012.06.030 ↗
39. Evaluation of heat of hydration of concrete containing high volume palm oil fuel ash10.1016/j.fuel.2012.10.020 ↗
40. Fabrication of a non-cement binder using slag, palm oil fuel ash and rice husk ash with sodium hydroxide10.1016/j.conbuildmat.2013.08.077 ↗
41. Compressive strength and microstructural analysis of fly ash/palm oil fuel ash based geopolymer mortar10.1016/j.matdes.2014.03.037 ↗
42. Strength, modulus of elasticity and shrinkage behaviour of POFA concrete
43. Pozzolanic reactivity of ultrafine palm oil fuel ash waste on strength and durability performances of high strength concrete10.1016/j.jclepro.2016.12.121 ↗
44. C. ASTM, Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete. ASTM Int., 2012. 4..
45. Engineering properties and carbon footprint of ground granulated blast-furnace slag-palm oil fuel ash-based structural geopolymer concrete10.1016/j.conbuildmat.2015.10.026 ↗
46. ASTM, ASTM C496/C496M-04e1 Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens. Annual book of ASTM standards 2008: section, 2008. 4.
47. Models relating mixture composition to the density and strength of foam concrete using response surface methodology10.1016/j.cemconcomp.2006.06.001 ↗
48. Influence of molarity and chemical composition on the development of compressive strength in POFA based geopolymer mortar10.1155/2015/647071 ↗
49. Factors affecting the suitability of fly ash as source material for geopolymers10.1016/j.fuel.2009.09.012 ↗
50. Characterisation of industrial side streams and their application for the production of geopolymer composites10.3390/min11060593 ↗
51. Solid reactant-based geopolymers from rice hull ash and sodium aluminate10.1007/s12649-016-9735-6 ↗
52. Effects of POFA replaced with FA on durability properties of GBFS included alkali activated mortars10.1016/j.conbuildmat.2018.04.166 ↗
53. Utilisation of fly ash in a geopolymeric material10.1016/S0883-2927(02)00005-7 ↗
54. Utilization of palm oil fuel ash in high-strength concrete10.1061/(ASCE)0899-1561(2004)16:6(623) ↗
55. Compressive strength and microstructural analysis of fly ash/palm oil fuel ash based geopolymer mortar under elevated temperatures10.1016/j.conbuildmat.2014.04.064 ↗
56. Fresh and hardened properties of palm oil clinker lightweight aggregate concrete incorporating Nano-palm oil fuel ash10.1016/j.conbuildmat.2019.04.101 ↗
57. Effect of high-volume ultrafine palm oil fuel ash on the engineering and transport properties of concrete
58. A.M. Neville, Properties of Concrete. Vol. 4. 1995: Longman London.
59. Effect of types of aggregate and sand-to-aggregate volume ratio on UPV in concrete10.1016/j.conbuildmat.2016.08.102 ↗
60. Properties and applications of foamed concrete; a review10.1016/j.conbuildmat.2015.10.112 ↗
61. Air-void characterisation of foam concrete10.1016/j.cemconres.2006.10.009 ↗
62. Lamond · 2006
63. Fly ash-based geopolymer lightweight concrete using foaming agent10.3390/ijms13067186 ↗
64. Durability performance of green concrete composites containing waste carpet fibers and palm oil fuel ash10.1016/j.jclepro.2016.12.151 ↗
65. N. Yassin, et al. Effects of Curing Conditions on Properties of Lightweight Concrete Brick Containing Expanded Polystyrene and Palm Oil Fuel Ash. in IOP Conference Series: Materials Science and Engineering. 2020. IOP Publishing.10.1088/1757-899X/713/1/012006 ↗
66. Reduction of indoor air temperature by using POFA foamed concrete block
67. The effect of porosity on the strength of foamed concrete10.1016/S0008-8846(01)00665-2 ↗
68. Waste metalized film food packaging as low cost and ecofriendly fibrous materials in the production of sustainable and green concrete composites10.1016/j.jclepro.2020.120726 ↗
69. Cellular concrete properties and the effect of synthetic and protein foaming agents10.1016/j.conbuildmat.2013.03.024 ↗
70. Influence of content and maximum size of light expanded clay aggregate on the fresh, strength, and durability properties of self-compacting lightweight concrete reinforced with micro steel fibers10.1016/j.conbuildmat.2019.117922 ↗
71. Microstructure of self-consolidating high strength concrete incorporating palm oil fuel ash
72. Experimental study of XRD, FTIR and TGA techniques in geopolymeric materials
73. Pore structure characterization of hardened cement paste by multiple methods10.1155/2019/2915684 ↗
74. Determination of the reactive component of fly ashes for geopolymer production using XRF and XRD10.1016/j.fuel.2010.07.031 ↗
75. Impact of added water and superplasticizer on early compressive strength of selected mixtures of palm oil fuel ash-based engineered geopolymer composites10.1016/j.conbuildmat.2016.01.033 ↗
76. Production of geopolymers using glass produced from DC plasma treatment of air pollution control (APC) residues10.1016/j.jhazmat.2009.11.089 ↗
77. Proposed simplified method of geopolymer concrete mix design10.32970/CS.2020.1.5 ↗
78. Understanding geopolymer binder-aggregate interfacial characteristics at molecular level10.1016/j.cemconres.2021.106582 ↗
79. NaOH-activated ground fly ash geopolymer cured at ambient temperature10.1016/j.fuel.2011.01.018 ↗
80. Catalytic materials based on silica and alumina: Structural features and generation of surface acidity10.1016/j.pmatsci.2019.04.003 ↗
81. Density functional calculations of the electronic structure and optical properties of aluminosilicate polymorphs (Al2SiO5)10.2138/am.2008.2664 ↗
82. The kinetics of mineral carbonation
83. Thermal behaviour of geopolymers prepared using class F fly ash and elevated temperature curing10.1016/j.cemconres.2006.03.022 ↗
84. J. Theo Kloprogge, R. Lavinsky, Chapter 1 – Introduction, in Photo Atlas of Mineral Pseudomorphism, J. Theo Kloprogge and R. Lavinsky, Editors. 2017, Elsevier. p. 1–115.10.1016/B978-0-12-803674-7.00001-3 ↗