journal article·2015-12Open access

Prediction of mechanical properties by means of semi-destructive methods: A review

Michal Kloiber, Miloš Drdácký, José S. Machado, Maurizio Piazza, Nobuyoshi Yamaguchi

Abstract

Methods and devices for in situ establishment of mechanical properties of wood have been recently developed in cooperation with European, US and Japanese researchers. The development of these new methods was motivated by requirements from engineers who need highly accurate data of mechanical properties of specific elements to plan renovations of historic buildings. Reliable data can replace overly conservative values (usually provided by visual strength grading) in structural analysis, which allows the retention of more original material as the behavior of specific elements is safely assessed. The recently developed methods, which are described in this chapter, are tensile strength of small samples, tensile Young's modulus of mesospecimens, compression strength of cores, compression strength in a drilled hole, mechanical resistance to pin pushing, Young's modulus derived by measuring the hardness and shear strength of screw withdrawals. Although in general the devices for the testing of mechanical properties by the mentioned methods provide more accurate results than the methods used so far, they are not yet mass produced, which should change soon.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Wood Treatment and Properties · Cultural Heritage Materials Analysis · Building materials and conservation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. UNI 11119, Cultural heritage – Wooden artifacts – load-bearing structures – on site inspections for the diagnosis of timber members, Ente Nazionale Italiano di Unificazione, UNI, Milano, Italy, 2004.
2. In situ assessment of structural timber using non-destructive techniques10.1617/s11527-013-0093-6 ↗
3. Guidelines for the on-site assessment of historic timber structures
4. A method for determining the allowable strength of in-lace wood structural members
5. Mechanical characterisation of wooden structures by means of an in situ penetration test. Elsevier Publishing Co., Oxford, England10.1016/S0950-0618(97)00080-9 ↗
6. M. Kloiber, J. Tippner, J. Hrivnák, L. Praus, Experimental verification of a new tool for wood mechanical resistance measurement, Wood Res. 57(3), ISSN, Slovakia, 1336–4561, (2012), 383–398, 2012.
7. B. Kasal, R. Anthony, Advances in in situ evaluation of timber structures, Prog. Struct. Eng. Mater., 6(2), John Villey & Sons Ltd., London, UK, pp. 94–103, 2004.10.1002/pse.170 ↗
8. ASTM, Annual Book of ASTM Standards, Section 4, Construction. 04.10 Wood, ASTM, Philadelphia, PA, 2002.
9. Semi-destructive methods for evaluation of timber structures. Structural studies, repairs and maintenance of heritage architecture VIII
10. M. Drdácký, I. Jirovský, Z. Slížková, On structural health and technological survey of historical timber structures, in: Proceedings of the International Conference the Conservation of Historic Wooden Structures, Florence, vol. I, pp. 278–284, 2005.
11. M. Kloiber, J. Frankl, M. Drdácký, I. Kučerová, J. Tippner, J. Bryscejn, Change of mechanical properties of Norway Spruce wood due to degradation caused by fire retardants, Wood Res., 55(4), ISSN, Slovakia, 1336–4561, 23–38, 2010.
12. Bodig · 1993 · 712
13. A semi-destructive tension method for evaluating the strength and stiffness of clear zones of structural timber elements in-service10.1016/j.conbuildmat.2012.02.041 ↗
14. R. Brites, Avaliação de Segurança das Estruturas Antigas de Madeira (Safety evaluation of old timber structures) (Ph.D. Dissertation), Universidade do Minho, Guimarães, 2011.
15. Semi-destructive method for in-situ evaluation of compressive strength of wood structural members
16. E. Schwab, A. Wasshau, H. Willetneier, Bohrkerne, Zur Beurteilung der Festigkeit holzerner Rammpfahle. Bauen mit Holz (9), 1982, 566–570.
17. M. Kloiber, M. Kotlínová, Prediction of mechanical properties by means of radial cores in situ, in: In-situ evaluation & non-destructive testing of historic wood and masonry structures, RILEM Workshop, 10–14 July 2006, Prague, pp. 56–65, ISBN: 978-80-86246-36-9.
18. ASTM: D 143-94 Standard Test Methods for Small Clear Specimens of Timber, ASTM International, For referenced ASTM standards, 2000.
19. M. Micka, J. Minster, P. Václavík, Compression test of a timber core – Ansys model and Moiré interferometry experiment, Eng. Mechanics, Svratka, (2006), 219/1–219/12.
20. M. Drdácký, I. Jirovský, J. Lesák, Non-destructive survey of masonry and timber structures of the Maria Tower on the Karlštejn Castle, Research Report ITAM-ARCCHIP, Praha, 62 p., 2003.
21. M. Drdácký, M. Kloiber, In-situ compression stress-deformation measurements along the timber depth profile, vol. 778, in: Advanced Materials Research, Trans Tech Publications, 209–216, 2013.10.4028/www.scientific.net/AMR.778.209 ↗
22. M. Kloiber, M. Drdácký, J. Tippner, V. Sebera, New construction NDT device for in situ evaluation of wood by using compression stress-deformation measurements parallel to grain, in: 18th International Nondestructive Testing and Evaluation of Wood Symposium, 2013, September 24–27, Madison, Wisconsin, USA, FPL-GTR-226, 585–592.
23. ČSN 49 0110: The breaking strength in compression along fibres, 1980.
24. ČSN 49 0111: Tests of the properties of solid wood, Method of detection of the module of elasticity in compression along fibres, 1992.
25. J. Maddox, M. Drdácký, M. Kloiber, J. Kunecký, In-situ assessment of strength of historic wood, in: 9th International Conference on Structural Analysis Historical Constructions, Mexico City, 10/2014, Mexico, ISBN: 04-2014-102011495500-102, 13 p.
26. M. Kloiber, M. Drdácký, J. Tippner, J. Hrivnák, Conventional compressive strength parallel to the grain and mechanical resistance of wood against pin penetration and microdrilling established by in-situ semidestructive devices, Mater. Struct., 2014–15, Netherlands, ISSN: 1359-5997, 15 p, doi:http://dx.doi.org/10.1617/s11527-014-0392-6.10.1617/s11527-014-0392-6 ↗
27. M. Kloiber, J. Tippner, M. Drdácký, Semi-destructive Tool for “In-situ” measurement of mechanical resistance of wood, in: SHATIŚ International Conference on Structural Health Assessment of Timber Structures, June 2011, Lisbon, Portugal, 3 p.
28. M. Kloiber, J. Tippner, J. Hrivnák, Mechanical properties of wood examined by semi-destructive devices, Mater. Struct., 47(1), 2014, Netherlands, ISSN: 1359-5997, 199–212, doi:http://dx.doi.org/10.1617/s11527-013-0055-z.10.1617/s11527-013-0055-z ↗
29. T. Tannert, R. Anthony, B. Kasal, M. Kloiber, M. Piazza, M. Riggio, F. Rinn, R. Widmann, N. Yamaguchi, Recommendation of RILEM TC 215-AST: in-situ assessment of structural timber using semi-destructive techniques, Mater. Struct., 2014, pp. 767–785, Netherlands, ISSN, pp. 1359–5997, doi:http://dx.doi.org/10.1617/s11527-013-0094-5.10.1617/s11527-013-0094-5 ↗
30. M. Kloiber, M. Kotlínová, J. Tippner, Estimation of wood properties using pin pushing in method with various shapes of the penetration pin, Acta Universitatis Agriculture et Silviculturae Mendelianae Brunensis, ISSN: 1211-8516, LVII, 2/2009, Brno, 53–60.10.11118/actaun200957020053 ↗
31. J. Tippner, M. Kloiber, J. Hrivnák, Derivation of mechanical properties by pushing of a pin into wood, vol. 2, in: 17th International Nondestructive Testing and Evaluation of Wood Symposium, 9/2011, Sopron, Hungary, 575–582, ISBN: 978-963-9883-83-3.
32. Screw resistance
33. D.W. Green, M. Begel, W. Nelson, Janka hardness using nonstandard specimens, Res. Note FPL-RN-0303, US Department of Agriculture, Forest Service, Forest Products Laboratory, Madison, WI, 13 p., 2006.10.2737/FPL-RN-303 ↗
34. ASTM: E 18-79 Standard test methods for Rockwell hardness and Rockwell superficial hardness of metallic materials, ASTM International, 1981.
35. Visual strength grading and NDT of timber in traditional structure10.1057/jba.2008.4 ↗
36. Il recupero dei solai in legno. Esperienze e realizzazioni
37. M. Piazza, G. Brentari, Criteri generali per la progettazione degli interventi di restauro di strutture lignee, in: “Il manuale del legno strutturale, vol. IV: Interventi sulle strutture”, Ed. Mancosu, 28–51, ISBN 88-87017-41-7, 2004.
38. R. Tomasi, M.I. Pezzo, M. Piazza, Rehabilitation of an historical theatre in Italy, Annali Museo Civico Rovereto, vol. 23, ISSN 1720-9161, 2007, 2008, 89–102.
39. N. Baldassino, M. Piazza, P. Zanon, Val Cadino timber bridge: non-destructive tests, analysis and diagnosis, in: 10th International Conference ‘Structural faults & repair 2003 – extending the life of bridges, concrete & composites, buildings, masonry & civil structures’, ISBN 0-947644-53-9 (CD-ROM), Commonwealth Institute, London.
40. F. Divos, L. Nemeth, L. Bejo, Evaluation of the Wooden Structure of a Baroque Place in Papa, Hungary, in: 11th international symposium on non-destructive testing of wood: Washington State University, USA, 153–160, 1998.
41. N. Yamaguchi, Withdrawal resistances by screw-based probes for in-situ assessment of wood, in: International conference on structural health assessment of timber structures, SHATIŚ International Conference on Structural Health Assessment of Timber Structures, June 2011, Lisbon, Portugal, 2011.
42. In situ assessment method of wood using normalized withdrawal resistances of metric-screw type probes10.4028/www.scientific.net/AMR.778.217 ↗
43. N. Yamaguchi, Inspection method of integrity of wood components in existing timber construction (Part 4). In situ evaluation using screw probe withdrawals, in: Summaries of Technical Papers of Annual Meeting, Structure III, Architectural Institute of Japan, 2014.
44. Hanhijärvi · 2005 · vol. 568