journal article·2015-11

The statistical interpretation of the strength of float glass for structural applications

Gabriele Pisano, Gianni Royer Carfagni

Publisher page

Abstract

Abstract The characteristic value of the strength of annealed float glass, to be used in structural calculations, is assessed by standards on the basis of a classical experimental campaign using the Coaxial Double Ring (CDR) test with additional overpressure. Experimental data were regressed according to the 2-parameter Weibull distribution, assuming that the induced state of stress is equibiaxial in practice. We show that, by splitting the data in two categories according to the surface under tensile stress (either the “tin” or the “air” side), a more accurate statistical interpretation can be obtained. Comparisons with the normal and log-normal distributions are made with the chi-square goodness-of-fit test. Moreover, we observe that the calibration curve suggested by the test standard is not precise, and that the stress state in the testing configuration is not equibiaxial. Therefore the rough data need to be further corrected and re-scaled to a common reference condition, according to a criterion of equal failure probability, by determining the effective area of the loaded specimen. Doing so, the considered statical distribution are able to fit to the data with much more accuracy. Considering that for very low failure-probabilities the tails of the statistics are the most important, and observing that the 2-parameters Weibull function fails to interpret a lower bound for the strength of glass that can be inferred from experiments, the use of a 3-parameter Weibull distribution is proposed. After having derived the corresponding expressions for the effective area, we present a new statistical characterization of glass strength that provides the best fit with the experimental data, at least for the air-side.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Analysis of Composite Materials · Building materials and conservation · Cultural Heritage Materials Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Safety factors for the structural design of glass10.1016/j.conbuildmat.2014.01.005 ↗
2. Structural performance of laminated and unlaminated tempered glass under monotonic transverse loading10.1016/j.conbuildmat.2005.01.051 ↗
3. Volume expansion caused by water penetration into silica glass10.1111/jace.13264 ↗
4. Stress corrosion and static fatigue of glass10.1111/j.1151-2916.1970.tb15962.x ↗
5. Effects of water and other dielectrics on crack growth10.1007/BF00752191 ↗
6. Critical issues in the design-by-testing of glass structures10.1016/j.engstruct.2015.04.025 ↗
7. Size effect model for the edge strength of glass with cut and ground edge finishing10.1016/j.engstruct.2014.08.004 ↗
8. Flexural strength of glass-ceramic for structural applications10.1016/j.jeurceramsoc.2013.10.032 ↗
9. CEN/TC129, EN 1288-2:2001 – Glass in Building – Determination of Bending Strength of Glass – Part 2: Coaxial Double Ring Test on Flat Specimens With Large Test Surface Areas, European Standard, 2001.
10. CEN/TC129, EN 1288:2001 – Glass in Building – Determination of the Bending Strength of Glass, European Standard, 2001.
11. G. Pisano, G. Royer-Carfagni, On the Coaxial Double Ring Test for Float Glass. Towards a New Standardized Configuration, 2015 (submitted for publication).
12. The effectiveness of resin-based repairs on the inert strength recovery of glass10.1016/j.conbuildmat.2015.03.072 ↗
13. A three-parameter Weibull statistical analysis of the strength variation of bulk metallic glasses10.1016/j.scriptamat.2009.07.038 ↗
14. Statistical features of strength characteristics for technical glasses10.1007/BF01523782 ↗
15. Method of reproducibly predamaging float glass as a basis to determine the bending strength
16. Weibull statistical analysis of the mechanical strength of a glass eroded by sand blasting10.1016/S0955-2219(99)00087-4 ↗
17. Modeling of probabilistic failure of Polycrystalline Silicon MEMS Structures10.1111/jace.13639 ↗
18. Deriving the primary cumulative distribution function of fracture stress for brittle materials from 3- and 4- point bending test10.1016/j.jeurceramsoc.2010.11.007 ↗
19. CEN/TC129/WG8, An overview of prEN-13474 and the work of CEN/TC129/WG8 from which it was developed, Internal document, 2006.
20. ASTM C1499 - 09, Standard Test Method for Monotonic Equibiaxial Flexural Strength of Advanced Ceramics at Ambient Temperature, The American Society for Testing and Materials, 2009.
21. A statistical distribution function of wide applicability10.1115/1.4010337 ↗
22. A general approach for the statistical analysis of multiaxial fracture10.1111/j.1151-2916.1978.tb09314.x ↗
23. R. Dall’Igna, A. D’Este, M. Silvestri, Comments on test methods for the determination of structural glass strength, in: Proceedings of XXV ATIV Conference, Parma, Italy, 2010, pp. 5–13.
24. Stress-corrosion mechanisms in silicate glasses10.1088/0022-3727/42/21/214006 ↗
25. Fracture surface energy of glass10.1111/j.1151-2916.1969.tb13350.x ↗
26. Munz · 1999
27. S. Choi, L. Powers, N. Nemeth, Slow Crack Growth Behavior and Life/Reliability Analysis of 96wt Alumina at Ambient Temperature with Various Specimen/Loading Configurations, Technical Memorandum 210206, NASA, 2000.
28. M. Schwob, G. Peyrache, Trait de fiabilit, Springer Series in Materials Science, Masson et Cie, 1969.
29. Maximum likelihood estimation in the Weibull distribution based on complete and on censored samples10.1080/00401706.1965.10490300 ↗
30. Karl Pearson and the chi-squared test10.2307/1402731 ↗