On factors affecting CFRP-steel bonded joints
Source abstract
Abstract
Abstract Failure of structural steel members strengthened with Carbon Fibre Reinforced Polymers (CFRP) may occur at the joints CFRP-steel and this study examines variables that alter or explain the corresponding reduction of load capacity for a specific CFRP laminate, adhesive and steel. Factors and parameters likely to be influential like surface treatment prior to bonding, the bonded length, the glass transition temperature (Tg) of the adhesive, the exposure to aggressive environment, the temperature at service and different types of loading were examined. The experimental program selected double strap CFRP-steel bonded joints under shear for the analysis. The steel surfaces to be bonded were subjected to sand blasting (6.3 bar) or abrasive grinding (6.9 bar) corresponding to thorough blast cleaning Sa2; surfaces rusted after exposure to salt fog at 35 °C were also considered. Differences detected in responses of specimens treated by sand or steel spheres blasting were relatively minor. Tests made at increasing ambient temperatures confirmed that service temperature near and above adhesive Tg caused rapid deterioration of ultimate capacity and change of failure modes. Salt fog cycles (SF) originated the most significant losses of joint capacity. Application of cyclic static loading above the critical loading threshold obtained for unaged joints did not reduce the capacity of joints previously aged by freeze-thaw. The same cyclic loading after salt fog cycles, reduced bond capacity and increase the ultimate slip, suggesting larger effective length. Despite the losses of capacity, microscopic changes of structural nature could not be identified.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Structural Response to Dynamic Loads
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Hollaway · 2001
2. Factors influencing the performance of externally bonded reinforcement systems of GFRP-to-concrete interface10.1617/s11527-014-0370-z ↗
3. Status of the Nation’s Highways, Bridges, and Transit: Conditions & Performance. Report to Congress. U.S. Department of Transportation, Federal Highway Administration, Federal Transit Administration, 2013.
4. Strengthening of a steel bridge girder using CFRP laminates10.1061/(ASCE)1084-0702(2001)6:6(514) ↗
5. Strengthening steel bridge sections using CFRP laminates10.1016/S1359-8368(01)00006-3 ↗
6. Application of FRP composites to bridges in the USA
7. Kirk · 2007
8. Shaat · 2004
9. State-of-the-art review on FRP strengthened steel structures10.1016/j.engstruct.2006.10.006 ↗
10. Strengthening of steel and concrete structures using CFRP in Japan
11. Q.H. Tawfik, W. Karunasena, Use of CFRP for Rehabilitation of Steel Structures: a Review, in: Southern Region Engineering Conference, 11–12 November 2010, Toowoomba, Australia, p. 1–5.
12. Fiber reinforced polymers for structural retrofitting: a review
13. Using fibre-reinforced polymer (FRP) composites to rehabilitate differing types of metallic infrastructure
14. S. Moy, V.M. Karbhari (Eds.). Strengthening of Historic Metallic Structures using Fibre-Reinforced Polymer (FRP) Composites Rehabilitation of Metallic Civil Infrastructure using Fiber-reinforced Polymer (FRP) Composites (2014), p. 406–429.10.1533/9780857096654.4.406 ↗
15. Strengthening of a 19th-century roadway metallic bridge using nonprestressed bonded and prestressed unbonded CFRP plates10.1016/j.conbuildmat.2019.03.095 ↗
16. Upgrading steel-concrete composite girders and repair of damaged steel beams using bonded CFRP laminates10.1016/j.tws.2008.10.014 ↗
17. Qaidar H. Tawfik, Warna (Karu) Karunasena, Use of CFRP for Rehabilitatio of Steel Structures: a review, in: Southern Region Engineering Conference 11–12 November 2010, Toowoomba, Australia.
18. Fatigue in adhesively bonded joints: a review201210.5402/2012/746308 ↗
19. An updated review of adhesively bonded joints in composite materials10.1016/j.ijadhadh.2016.10.010 ↗
20. Fracture mechanics tests in adhesively bonded joints: a literature review10.1080/00218464.2013.859075 ↗
21. Environmental durability of adhesively bonded FRP/steel joints in civil engineering applications: state of the art10.1016/j.compositesb.2015.07.014 ↗
22. Adhesive joints for low- and high-temperature use: an overview10.1080/00218464.2014.943395 ↗
23. Effect of material, geometry, surface treatment and environment on the shear strength of single lap joints10.1016/j.ijadhadh.2009.02.012 ↗
24. Effect of adhesive thickness, adhesive type and scarf angle on the mechanical properties of scarf adhesive joints10.1016/j.ijsolstr.2013.09.005 ↗
25. Curing effects on steel/CFRP double strap joints under combined mechanical load, temperature and humidity10.1016/j.conbuildmat.2012.11.035 ↗
26. Environmental ageing on GFRP pultruded joints: comparison between different adhesives10.1016/j.compstruct.2015.07.067 ↗
27. Estimations of the debonding process of aged joints through a new analytical method10.1016/j.compstruct.2018.12.053 ↗
28. Bond durability of CFRP-to-Steel joints subjected to freeze thaw10.1016/j.compstruct.2019.01.016 ↗
29. CFRP-to-steel bonded joints subjected to cyclic loading: an experimental study10.1016/j.compositesb.2018.03.039 ↗
30. Bond characteristics of CFRP-to-steel joints10.1016/j.jcsr.2017.08.001 ↗
31. A temperature-dependent bond-slip model for CFRP-to-steel joints10.1016/j.compstruct.2019.03.019 ↗
32. Influence of freeze-thaw cycling on the bond strength of steel-FRP lap joints10.1016/j.compositesb.2013.12.024 ↗
33. 2011
34. The effect of surface roughness on strength of adhesively bonded cylindrical components10.1016/S0924-0136(03)00463-1 ↗
35. Influence of adherend surface roughness on the adhesive bond strength10.1590/1679-78253066 ↗
36. Treatment of steel surfaces for effective adhesive bonding
37. LSM 700 – Full Manual. Carl Zeiss MicroImaging GmbH M60-1-0036 e, p204. 07740 Jena, Germany. September 2011.
38. Leach · 2008
39. ISO 16610-21. Geometrical Product Specifications (GPS) – Filtration – Part 21: Linear Profile Filters: Gaussian Filters (2011).
40. Surface topography effect on strength of lap adhesive joints after mechanical pre-treatment10.1016/j.acme.2013.02.005 ↗
41. Effect of laser and plasma surface cleaning on mechanical properties of adhesive bonded joints10.1016/j.procir.2015.06.054 ↗
42. Tensile response of steel/CFRP adhesive bonds for the rehabilitation of civil structures10.12989/sem.2005.20.5.589 ↗
43. Behaviour of CFRP-to-steel interfaces in adhesively bonded joints
44. Modeling of steel beams strengthened with CFRP Strips including bond-slip properties
45. Design aspects of concrete structures strengthened with externally bonded CFRP-plates
46. Stress transfer and fracture propagation in different kinds of adhesive joints
47. Delamination process analysis of FRP-to-parent material bonded joints with and without anchorage systems using the distinct element method10.1016/j.compstruct.2014.04.021 ↗
48. A new discrete method to model unidirectional FRP-to-parent material bonded joints subjected to mechanical loads10.1016/j.compstruct.2014.10.036 ↗
49. Effect of temperature variation on bond characteristics between CFRP and steel plate
50. Bond-slip model for FRP laminates externally bonded to concrete at elevated temperature10.1061/(ASCE)CC.1943-5614.0000337 ↗
51. Development of bond strength model for CFRP-to-concrete joints at high temperatures10.1016/j.compositesb.2016.03.088 ↗
52. Effect of temperature variation on bond characteristics between CFRP and steel plate10.1155/2016/5674572 ↗
53. The influence of temperature variations on adhesively bonded structures: a non-linear theoretical perspective10.1016/j.ijnonlinmec.2019.03.001 ↗
54. Yang · 2019 · 196