Comparative study on the properties of WMA mixture using foamed admixture and free water system
Source abstract
Abstract
Abstract Warm mix asphalt (WMA) technologies that use a foaming effect are one of the most commonly used WMA technologies due to their cost-effectiveness. The concept behind the foamed WMA is that the water turns to steam and is dispersed throughout the asphalt, which provides corresponding temporary reductions in viscosity while requiring no extra additives. The purpose of this paper is to evaluate both WMA techniques using foamed admixture and free water systems. For foamed admixture, ADVERA® WMA was selected; whereas for free water systems, WMA was foamed by injecting a small amount of water that was produced under a laboratory setup. Subsequently, for the asphalt mixture preparation, the mixture design used was based on specifications for a local asphalt mixture used in Michigan, USA. The nominal maximum aggregate size is 9.5 mm and the designed traffic level is less than 3 million ESALs based on the current Superpave™ asphalt mixture design procedure. The control mixture and WMA mixture were evaluated through the asphalt pavement analyzer rutting test, flow number test, indirect tensile strength ratio, and the four point beam fatigue test. From the results, it was found the fatigue life of most of the samples prepared with ADVERA® WMA were higher than the control hot mix asphalt (HMA). However, foamed WMA has a significantly lower aging factor compared to control HMA which results in higher rutting potential.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Concrete Properties and Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Button · 2007
2. Warm mix asphalt for cold weather paving
3. Structural properties of laboratory mixtures containing foamed asphalt and marginal aggregates
4. D’Angelo J, et al. Warm mix asphalt: European Practice. Office of International Programs, Office of Policy, Federal Highway Administration, US Department of Transportation, American Association of State Highway and Transportation Officials, National Cooperative Highway Research Program; 2008.
5. Barthel W, Marchand J-P, Devivere MV. Warm asphalt mixes by adding a synthetic zeolite. In: Eurasphalt & eurobitume congress proceedings; 2004.
6. Anderson RM, et al. Engineering properties, emissions, and field performance of warm mix asphalt technology (NCHRP); 2008.
7. FHWA. Warm Mix Asphalt Technologies and Research; 2007 .
8. Brown · 2007 · vol. 77
9. Ventura A, et al. Environmental comparison at industrial scale of hot and half-warm mix asphalt manufacturing processes. In: Transportation research board 88th annual meeting, transportation research board; 2009. 12p.
10. Xiao F, Amirkhanian S. Laboratory investigation of moisture damage in warm-mix asphalt containing moist aggregate. In: Transportation research board 88th annual meeting, transportation research board; 2009. 17p.10.3141/2126-14 ↗
11. Low-energy asphalt with performance of hot-mix asphalt10.1177/0361198106196200112 ↗
12. Olard F, Heritier B, Beduneau E. Low energy asphalt LEA®: new half-warm mix asphalt for minimizing impacts from asphalt plant to job site. In: International symposium on asphalt pavement and environment, Zurich (ISAP 2008) Zurich (Switzerland); 2008.
13. Gaudefroy V, et al. Laboratory environmental assessment of half-warm mix asphalts by factorial experiment design approach. In: Transportation research board 88th annual meeting 2009: transportation research board; 2009. 24p.
14. Middleton B, Forfylow B. Evaluation of warm-mix asphalt produced with double barrel green process. In: Transportation research board 88th annual meeting, transportation research board; 2009. 14p.10.3141/2126-03 ↗
15. Wielinski JC, Hand AJT, Rausch DM. Laboratory and field evaluations of foamed warm-mix asphalt projects. In: Transportation research board 88th annual meeting, transportation research board; 2009. 18p.10.3141/2126-15 ↗
16. AESCO/Madsen, Eco Foam-II Static Inline Vortex Mixer. [Cited at March 2011]; 2011. .
17. Stansteel, Double Barrel Green System. [Cited at April 2011]; 2011. .
18. Tarmc. Tri-mix warm mix injection. Tarmac International Inc. [Cited May 2011]; 2011.
19. Terex. Warm mix asphalt system. Terex Corporation [Cited March 2011]; 2011. .
20. James R. Metering of steam water two phase flow by sharp edged orifices. In: Proceedings of the Institution of Mechanical Engineers 1847–1996; 1965.10.1243/PIME_PROC_1965_180_038_02 ↗
21. Superpave performance graded asphalt binder specification and testing. 3rd ed. Asphalt Institute; 2003. 69 p.
22. Superpave performance graded asphalt binder specification and testing. Asphalt Institute; 1995. 78p.
23. Superpave. Asphalt Institute; 1996. 126p.
24. PQCorp, Advera® WMA Alumino Silicate PQ Corporation (cited at January 2011); 2011.
25. Goh SW, You Z. Moisture damage and fatigue cracking of foamed warm mix asphalt using a simple laboratory setup. In: Transportation and Development Institute Congress 2011@ sIntegrated Transportation and Development for a Better Tomorrow. ASCE; 2011.10.1061/41167(398)73 ↗
26. Wasiuddin NM, et al. A comparative laboratory study of Sasobit® and Aspha-min® in warm-mix asphalt. In: Transportation research board 86th annual meeting. Washington DC, United States; 2007.10.3141/1998-10 ↗
27. Simple performance test for fatigue cracking and validation with WesTrack mixtures10.3141/1789-07 ↗
28. Verification and modeling of three-stage permanent deformation behavior of asphalt mixes
29. Permanent deformation characteristics of subgrade soils due to repeated loading
30. Estimating results of a proposed simple performance test for hot-mix asphalt from superpave gyratory compactor results10.1177/0361198105192900113 ↗
31. Witczak MW. Specification criteria for simple performance tests for rutting, NCHRP Report 580, NCHRP Report 580, National Cooperative Highway Research Program; 2007.
32. Refinement of flow number as determined by asphalt mixture performance10.3141/2127-15 ↗
33. Witczak MW, et al. Simple performance test for superpave mix design, NCHRP Report 465, National Cooperative Highway Research Program; 2002.
34. Repeated triaxial testing during mix design for performance characterization10.3141/1767-10 ↗
35. AASHTO:T321. Determining the fatigue life of compacted hot-mix asphalt (HMA) subjected to repeated flexural bending. American Association of State Highway and Transportation Officials; 2007.