journal article·2019-01

Preparation and properties of ultra-lightweight EPS concrete based on pre-saturated bentonite

Yue Xie, Jun Li, Zhongyuan Lu, Jun Jiang, Yunhui Niu

Publisher page

Abstract

Abstract Water-rich gel of pre-saturated bentonite exhibits multiscale pore structures, which can be used as pore-forming agent to prepare porous concrete without any air entraining agents. In this study, pre-saturated bentonite with solid content of 11.1% was used to prepare ultra-lightweight EPS concrete at various dry density levels (300, 400, 500 and 600 kg/m3). For fresh mixtures (without EPS beads), yield stress increased while apparent viscosity decreased with the increased dosage of pre-saturated bentonite. The slump-flow of fresh mixture (with EPS beads) showed a growth trend, which had negative correlations with apparent viscosity. Meanwhile, the slump-flow was also affected by the wet density change. Thermal insulation of ultra-lightweight EPS concrete was improved by 14–31% compared to that of ordinary foamed concrete at the corresponding density. Thermal conductivities of 0.062–0.129 W·m−1·k−1 at dry densities of 300–600 kg/m3 were observed. Compressive strength decreased at lower density (≤400 kg/m3), but increased at higher density (≥500 kg/m3) with the increase of pre-saturated bentonite. The construction of plentiful multiscale pores by pre-saturated bentonite is the main reason for the lower thermal conductivity, while also can cause an increase in volumetric water absorption.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Aerogels and thermal insulation · Recycling and utilization of industrial and municipal waste in materials production

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. A study of city-level building energy efficiency benchmarking system for China10.1016/j.enbuild.2018.08.038 ↗
2. Energy efficiency evaluation of zero energy houses10.1016/j.enbuild.2014.06.019 ↗
3. Development and performance evaluation of natural thermal-insulation materials composed of renewable resources10.1016/j.enbuild.2011.06.012 ↗
4. A case study on life cycle energy use of residential building in Southern India10.1016/j.enbuild.2014.05.034 ↗
5. Proportioning and characterization of Portland cement-based ultra-lightweight foam concretes10.1016/j.conbuildmat.2015.01.051 ↗
6. A comparative embodied energy analysis of a house with recycled expanded polystyrene (EPS) based foam concrete wall panels10.1016/j.enbuild.2016.11.044 ↗
7. Structural concrete using sintered flyash lightweight aggregate: a review10.1016/j.conbuildmat.2017.08.005 ↗
8. Thermal-resistant lightweight concrete with polyethylene beads as coarse aggregates10.1016/j.conbuildmat.2018.01.012 ↗
9. Lightweight concrete production with low Portland cement consumption10.1016/j.jclepro.2011.10.010 ↗
10. A review of expanded polystyrene (EPS) properties, performance and new applications
11. Experimental application of EPS concrete in the new prototype design of the concrete barrier10.1016/j.conbuildmat.2016.07.105 ↗
12. Structural feasibility of expanded polystyrene (EPS) based lightweight concrete sandwich wall panels10.1016/j.conbuildmat.2017.02.027 ↗
13. Recycling of EPS: a new methodology for production of concrete impregnated with polystyrene (CIP)10.1016/j.cemconcomp.2007.05.014 ↗
14. Effects of expanded polystyrene (EPS) particles on fire resistance, thermal conductivity and compressive strength of foamed concrete10.1016/j.conbuildmat.2016.02.218 ↗
15. Mechanical and thermal properties of lightweight concretes with vermiculite and EPS using air-entraining agent10.1016/j.conbuildmat.2014.02.009 ↗
16. Characterization and simulation of microstructure and properties of EPS lightweight concrete10.1016/j.cemconres.2007.08.028 ↗
17. Influence of EPS, mineral wool and plaster layers on sound and thermal insulation of a wall: a case study10.1016/j.apacoust.2018.03.001 ↗
18. Behaviour of lightweight expanded polystyrene concrete containing silica fume10.1016/S0008-8846(02)01055-4 ↗
19. Mechanical properties of polymer-modified concretes containing expanded polystyrene beads10.1016/j.conbuildmat.2005.08.001 ↗
20. Evaluation of the fluidity and mechanical properties of light-weight self-compacting concrete containing expanded polystyrene
21. Effects of anti-washout admixtures on fresh concrete properties
22. Effects of viscosity modifying admixture (VMA) on workability and compressive strength of structural EPS concrete10.1016/j.conbuildmat.2018.04.176 ↗
23. Effect of viscosity type modifying admixture on porosity, compressive strength and water penetration of high performance self-compacting concrete10.1016/j.conbuildmat.2013.07.076 ↗
24. Effect of viscosity stabilizing agents on the properties of self-compacting mortars and concretes
25. An investigation on the fresh properties of self-compacted lightweight concrete containing expanded polystyrene10.1016/j.conbuildmat.2011.04.018 ↗
26. Kaolinite flocculation induced by smectite addition – A transmission X-ray microscopic study10.1016/j.jcis.2010.05.019 ↗
27. Transmission X-ray microscopy (TXM) reveals the nanostructure of a smectite gel10.1021/la800986t ↗
28. A cryo-SEM study of aggregate and floc structure changes during clay settling and raking processes10.1016/j.minpro.2009.06.004 ↗
29. Effect of surface structure of kaolinite on aggregation, settling rate, and bed density10.1021/la100088n ↗
30. Microstructure, permeability and rheology of bentonite — Cement slurries10.1016/0008-8846(90)90115-E ↗
31. Time-dependent rheological behavior of bentonite suspensions: an experimental study10.1122/1.2079267 ↗
32. Modeling rheological behavior of bentonite suspensions as Casson and Robertson-Stiff fluids using Newtonian and true shear rates in Couetteviscometry10.1016/j.powtec.2006.07.011 ↗
33. Effects of bentonite slurry on air-void structure and properties of foamed concrete10.1016/j.conbuildmat.2018.05.226 ↗
34. Effect of aggregate on drying shrinkage of concrete10.4028/www.scientific.net/AMR.168-170.701 ↗
35. GB 175-2007, Common Portland cement, 2007.
36. Rheology of fresh cement asphalt emulsion pastes10.1016/j.conbuildmat.2015.01.078 ↗
37. Influence of crushed aggregate fines with micro-proportioned particle size distributions on rheology of cement paste10.1016/j.cemconcomp.2017.02.012 ↗
38. Effect of mixing method on microstructure and rheology of cement paste10.1016/j.conbuildmat.2015.05.124 ↗
39. Linking yield stress measurements: spread test versus Viskomat10.1016/j.cemconres.2005.08.001 ↗
40. GB/T 50080-2016, Standard for test method of performance on ordinary fresh concrete, 2016.
41. GB/T 10294-2008, Thermal insulation-Determination of steady-state thermal resistance and related properties-Guarded hot plate apparatus, 2008.
42. JG/T 266-2011, Foamed concrete, 2011.
43. Aerogel insulation for building applications: a state-of-the-art review10.1016/j.enbuild.2010.12.012 ↗
44. Traditional, state-of-the-art and future thermal building insulation materials and solutions – Properties, requirements and possibilities10.1016/j.enbuild.2011.05.015 ↗
45. Numerical study on the effect of pore shapes on the thermal behaviors of cellular concrete10.1016/j.conbuildmat.2017.12.108 ↗
46. Kinetics of lime/bentonitepozzolanic reactions at 20 and 50 degrees C: batch tests and modeling10.1016/j.cemconres.2014.01.024 ↗
47. Si-29 solid state NMR investigation of pozzolanic reaction occurring in lime-treated Ca-bentonite10.1016/j.cemconres.2012.01.008 ↗