Experimental bond behavior of Steel Reinforced Grout systems for strengthening concrete elements
Source abstract
Abstract
Abstract Composite materials consisting of high tensile strength steel cords embedded in a cementitious matrix (Steel Reinforced Grout, SRG) are becoming an attractive solution for strengthening existing structures thanks to the lower cost than “traditional” FRP systems, the isotropy of the steel and the ability of the mortar to resist fire. With respect to Steel Reinforced polymer (SRP) systems – whose mechanical behavior is predominantly dependent on the strength of the substrate to which the steel fibers are epoxy bonded – the mechanical properties of SRG systems are mainly dependent on the cement-based matrix which is sensitive to curing the installation conditions and methods. The experimental results presented and discussed in this paper contribute to expanding the existing knowledge on the bond behavior between the SRG and concrete substrate. To this purpose, a number of SRG strips were bonded to concrete blocks by an inorganic matrix and the lap joint was subsequently subjected to direct shear tests performed in displacement control. Since mortars are very sensitive to environmental conditions and humidity as previously mentioned, two different curing conditions were used. In the first case – termed “curing a” – specimens were cured at room temperature for 28 days and wet cloths were placed on top of the composite surface each day for two weeks. In the second case – termed “curing b” – specimens were just cured at room temperature for 28 days. In addition to the curing condition, the following study parameters were considered: (a) the concrete surface roughness in the bonded region, (b) the density of the dry steel fabric, (c) the bonded interface length, and (d) the concrete strength. Relatively to the latter parameter, concrete prisms were broadly divided into two strength groups: Normal Strength Concrete (NSC) having an average concrete cylindrical strength between 13 and 25 MPa and High Strength Concrete (HSC) having an average strength equal to 40 MPa. Experimental evidence underlines that SRG systems mainly exhibited a debonding failure at steel fibers-matrix interface (due to the sliding phenomena) irrespective of the concrete strength and surface finish. Furthermore, like the SRP systems, the low tape density showed better performances with respect to the higher densities considered in this paper, both in terms of the efficiency factor (i.e., the ratio between the tensile stress experienced by SRG in each test and the average tensile ultimate strength of dry steel fabric) and of the maximum force transferred by the system.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Innovative concrete reinforcement materials · Masonry and Concrete Structural Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. A 1D finite element model for the flexural behaviour of RC beams strengthened with MF-FRP strips10.1016/j.compstruct.2013.07.058 ↗
2. Flexural behaviour of RC members strengthened with FRCM: state-of-the-art and predictive formulas10.1016/j.compositesb.2018.04.051 ↗
3. FRP-Steel study of IM and UHM CFRP strips10.1016/j.conbuildmat.2018.07.109 ↗
4. Experimental bond behaviour of a CFRP strengthening system for concrete elements at elevated temperatures10.1016/j.conbuildmat.2018.10.184 ↗
5. Analysis of bond performance between CFRP sheets and calcarenite ashlars under service and ultimate conditions
6. Cementitious composites reinforced with continuous carbon fibers for strengthening of concrete structures10.1016/S0958-9465(02)00054-9 ↗
7. Efficiency of CFRP NSM strips and EBR plates for flexural strengthening of RC beams and loading pattern influence10.1016/j.compstruct.2014.12.046 ↗
8. Bond of NSM FRP strengthened concrete: round robin test initiative
9. Experimental analysis of the bond behavior of glass, carbon, and steel FRCM composites10.4028/www.scientific.net/KEM.624.371 ↗
10. A short review on basalt fiber
11. Basalt fiber: an ancient material for innovative and modern application
12. A green material from rock: basalt fiber a review10.1080/00405000.2015.1071940 ↗
13. A review on basalt fiber and its composites10.1016/j.compositesb.2014.12.034 ↗
14. Dynamic bond stress-slip relationship between basalt FRP sheet and concrete under initial static loading
15. Strain rate effect on effective bond length of basalt FRP sheet bonded to concrete10.1016/j.conbuildmat.2015.02.016 ↗
16. Bond behavior between basalt fiber reinforced polymer sheet and concrete substrate under the coupled effects of freeze-thaw cycling and sustained load10.1061/(ASCE)CC.1943-5614.0000349 ↗
17. Bond strength and effective bond length of FRP sheets/plates bonded to concrete considering the type of adhesive layer10.1016/j.compositesb.2013.10.075 ↗
18. Behaviour of reinforced concrete beams strengthened with basalt textile reinforced concrete10.1177/1528083714521068 ↗
19. A numerical failure analysis of multi-bolted joints in FRP laminates based on basalt fibers10.1016/j.proeng.2015.06.255 ↗
20. Nerilli · 2016
21. Experimental analysis on bond between PBO-FRCM strengthening materials and concrete10.1016/j.compositesb.2012.03.011 ↗
22. Influence of the substrate characteristics on the bond behavior of PBO FRCM-concrete joints10.1016/j.conbuildmat.2015.10.045 ↗
23. Round Robin Test on the tensile and bond behaviour of Steel Reinforced Grout systems
24. An experimental investigation on the bond behaviour of steel reinforced polymers on concrete substrate10.1016/j.compstruct.2017.08.063 ↗
25. Double-leaf masonry walls under in-plane loading strenghtened with GFRP/SRG strips10.1016/j.engstruct.2016.09.042 ↗
26. Characterization of reinforced concrete beams strengthened by steel reinforced polymer and grout (SRP and SRG) composites10.1016/j.msea.2005.08.151 ↗
27. Carloni · 2018 · 326
28. Properties and potential for application of steel reinforced polymer and steel reinforced grout composites10.1016/S1359-8368(03)00080-5 ↗
29. Strengthening of a reinforced concrete bridge with externally bonded Steel Reinforced Polymer (SRP)10.1016/j.compositesb.2006.09.003 ↗
30. SRG/SRP-concrete bond-slip laws for externally strengthened RC beams10.1016/j.compstruct.2015.06.068 ↗
31. Ascione · 2018 · 326
32. Bond behaviour of steel reinforced polymer strengthening systems10.1016/j.compstruct.2016.05.052 ↗
33. Strengthening of structures with Steel Reinforced Polymers: a state-of-the-art review10.1016/j.compositesb.2016.08.025 ↗
34. Bond behavior of SRG-strengthened masonry units: testing and numerical modeling10.1016/j.conbuildmat.2014.04.070 ↗
35. Bond behaviour of Steel Reinforced Grout for the extrados strengthening of masonry vaults10.1016/j.conbuildmat.2017.06.010 ↗
36. Reinforced concrete beams strengthened with SRP/SRG systems: experimental investigation10.1016/j.conbuildmat.2015.06.027 ↗
37. Compressive behavior of concrete confined by SRP wraps10.1016/j.conbuildmat.2016.01.055 ↗
38. Full scale reinforced concrete beam-column joints strengthened with steel reinforced polymer systems
39. Modeling SRP-concrete interfacial bond behavior and strength10.1016/j.engstruct.2019.02.050 ↗
40. Material and bonding characteristics for dimensioning and modeling of textile reinforced concrete (TRC) elements10.1617/s11527-006-9140-x ↗
41. Shear strengthening of reinforced concrete members with textile reinforced mortar (TRM) jackets10.1007/s11527-005-9034-3 ↗
42. Experimental study of adhesion between FRCM and masonry support10.4028/www.scientific.net/KEM.624.189 ↗
43. A qualification method for externally bonded Fiber Reinforced Cementitious Matrix (FRCM) strengthening systems10.1016/j.compositesb.2015.03.079 ↗
44. On the design of shear-strengthened RC members through the use of textile reinforced mortar overlays10.1016/j.compositesb.2018.04.008 ↗
45. Textile-reinforced mortar versus fiber-reinforced polymer confinement in reinforced concrete columns
46. Textile-reinforced mortar versus FRP jacketing in seismic retrofitting of RC columns with continuous or lap-spliced deformed bars10.1061/(ASCE)CC.1943-5614.0000028 ↗
47. Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: out of- plane cyclic loading10.1617/s11527-007-9226-0 ↗
48. Mechanical properties and numerical modeling of Fabric Reinforced Cementitious Matrix (FRCM) systems for strengthening of masonry structures10.1016/j.compstruct.2013.08.026 ↗
49. Italian National Research Council. CNR-DT215/2018. Istruzioni per la Progettazione, l’Esecuzione ed il Controllo di Interventi di Consolidamento Statico mediante l’utilizzo di Compositi Fibrorinforzati a matrice inorganica. Rome, 2018.
50. American Concrete Institute. ACI 549.4R-13 Guide to design and construction of externally bonded Fabric Reinforced Cementitious Matrix (FRCM) systems for repair and strengthening concrete and masonry structures. Farmington Hills, MI, USA, 2013
51. Kerakoll S.p.A. – web site: (accessed 1.18).