Shear strength of epoxy anchors embedded into low strength concrete
Source abstract
Abstract
Abstract Chemical anchors are getting more frequently used to connect structural elements. The studies regarding the chemical anchors embedded in low strength concrete are very limited in the literature. However, the compressive strength of the concrete may be 10 MPa or lower in many strengthening applications. Steel bars having 12, 16 and 20 mm diameters have been selected as the anchor rod in this study. They have been embedded in to concrete blocks with 5.9 and 10.9 MPa compressive strength. Solvent-free epoxy based three component chemical adhesive has been used for the connection between concrete and anchor bar. The depth of holes is 10, 15 and 20 times that of the anchor diameter. The anchors have been embedded such that they are sufficiently away from the free edge so as not to cause any concrete failure. The load–displacement cycles of all anchors have been obtained by reversed cyclic tests with incremental displacement. The obtained results indicate that increasing the anchor diameter have decreased the shear strength. Even though the anchor damage has been caused by steel failure, a decrease in shear capacity was observed with the lower strength concrete.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Bond stress model for design of adhesive anchors
2. Behavior and design adhesive bonded anchors
3. ACI318-05. Building code requirements for reinforced concrete. Detroit (USA): American Concrete Institute; 2005.
4. ACI355.2-07. Qualification of post-installed mechanical anchors in concrete and commentary. USA: American Concrete Institute; 2007.
5. Performance requirements for structural adhesives in relation to concrete strengthening10.1016/S0143-7496(01)00019-7 ↗
6. Shear strength of adhesive anchors10.15554/pcij.09012002.92.101 ↗
7. Analysis of steel/concrete interfacial shear stress by means of pull out test10.1016/j.ijadhadh.2007.02.006 ↗
8. Pullout simulation of post installed chemically bonded anchors10.1061/(ASCE)0733-9445(1996)122:9(1016) ↗
9. Estimation of ultimate tension load of methylmethacrylate bonded steel rods into concrete10.1016/j.ijadhadh.2006.12.001 ↗
10. Factors influencing bond strength of adhesive anchors
11. Model for pullout strength of anchors in concrete10.1061/(ASCE)0733-9445(1983)109:5(1155) ↗
12. Parametric study of factors affecting the pull-out strength of steel rods bonded into precast concrete panel10.1016/S0143-7496(01)00028-8 ↗
13. Tensile behavior of post-installed anchors in plain and steel fiber-reinforced normal- and high strength concretes
14. Concrete anchors
15. Load–deflection behavior of cast-in-place and retrofit concrete anchors
16. The failure mechanism and the pull-out strength of a bond-type anchor near a free edge10.1016/S0167-6636(97)00052-5 ↗
17. The behavior of chemical, grouted and mechanical anchors under tensile and shear loads
18. Chemically bonded anchors subjected to rapid pullout loading
19. Breakout capacity of anchors in concrete part 1: tension
20. Gürbüz T, Seyhan E, İlki A, Kumbasar N. Behavior of chemical anchors used in strengthening works under axial tension effect. In: Sixth conference on national earthq. eng. October 16–20, İstanbul; 2007. p. 649–59 [in Turkish].
21. Shear capacity of steel anchor bolts and welded studs: a literature review
22. Effect of reinforcing details on the shear resistance of short anchor bolts under reversed cyclic loading
23. Experimental investigation of anchor bolts under shear10.1061/(ASCE)0733-9445(1990)116:4(910) ↗
24. Static behavior of anchors under combinations of tension and shear loading
25. Dynamic behavior of single and double near-edge anchors loaded in shear
26. Prediction of shear capacity of single anchors located near a concrete edge using neural networks10.1016/j.compstruc.2005.03.019 ↗
27. Three-dimensional modeling of anchorage subject to shear loads
28. Concrete capacity design (CCD) approach for fastening to concrete
29. PCI design handbook-precast and prestressed concrete, 5th ed. Chicago: Precast/Prestressed Concrete Institute; 1999.
30. Prediction of tensile capacity of single adhesive anchors using neural networks10.1016/j.compstruc.2005.02.008 ↗
31. Turkey—Bingöl earthquake: damage in reinforced concrete structures10.1016/j.engfailanal.2003.08.005 ↗
32. Detailed assessment of structural characteristics of Turkish RC building stock for loss assessment models10.1016/j.soildyn.2007.10.005 ↗