journal article·2014-11Open access

Inorganic stabilisation methods for extruded earth masonry units

Daniel Maskell, Andrew Heath, Pete Walker

Abstract

Abstract Addressing the challenges of embodied environmental impact of materials has led to growing interest in the use of earth as a construction material. Adopting large-scale commercial methods of extruded brick production has potential to overcome many of the existing barriers of adoption. Without the firing the bricks will have a significantly lower embodied environmental impact and similar dimensions (just over 100 mm thick in the UK) to conventional masonry. However, the wider adoption of 100 mm thick unfired earth masonry is dependent on its suitability for use in structurally load-bearing applications. Currently the greatest barrier to earth masonry adoption is the durability of the material when subjected to high moisture contents. Accidental or intentional wetting of a 100 mm thick load bearing unfired earth wall could lead to disproportionate collapse unless the moisture resistance is improved. To overcome the concern of elevated moisture contents, a common approach is to chemically stabilise the soil using either cement or lime. While there has been research into the use of cement and lime for other forms of earth construction, their use for extruded earth bricks has not been investigated in depth. The source materials and inherent physical properties of extruded earth bricks are different to other forms of earthen construction. Therefore the suitability of cement and lime to stabilise soil for the purpose of extruded earth bricks requires investigation. This research demonstrates the improvement in 28 day compressive strength, with a range of cement or lime contents and three initial curing temperatures. Small scale bricks were tested in both the ambient environmental conditions and following 24 h of full submersion in water. Key factors, such as density and moisture content, are shown to be important for compressive strength development. The effect of stabilisation has been shown to be more important as a determinant for strength than density and moisture content alone.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hygrothermal properties of building materials · Innovations in Concrete and Construction Materials · Masonry and Concrete Structural Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. A plasticity chart as an aid to the identification and assessment of industrial clays10.1180/claymin.1971.009.1.01 ↗
2. Bloodworth A, Cowley J, Highley D, Bowler G. Brick clay: issues for planning. british geological survey commissioned report CR/01/117N; 2001.
3. BS 5930:1999. Code of practice for site investigations. British Standards Institute (BSI); 2010.
4. BS EN 772-1:2000. Methods of test for masonry units – Part 1: Determination of compressive strength. British Standards Institute (BSI); 2000.
5. Greaves H. An introduction to lime stabilisation. In: Lime stabilisation: proceedings of the seminar held at Loughborough University Civil & Building Engineering Department on 25 September, 1996. Amer Society of Civil Engineers, 1996.10.1680/ls.25639.0002 ↗
6. Compressive strength of extruded unfired clay masonry units
7. Modern earth masonry: structural properties and structural design10.56330/UGAV7711 ↗
8. Houben · 1994
9. The strength of unstabilised rammed earth materials10.1680/geot.2007.00129 ↗
10. Laboratory scale testing of extruded earth masonry units10.1016/j.matdes.2012.09.008 ↗
11. Maskell D. Development of stabilised extruded earth masonry units. (Unpublished doctoral dissertation). Bath, UK: University of Bath; 2013
12. Comparing the environmental impact of stabilisers for unfired earth construction10.4028/www.scientific.net/KEM.600.132 ↗
13. Minke · 2006
14. Unfired clay bricks: from laboratory to industrial production
15. Compressive strength and microstructural analysis of unfired clay masonry bricks10.1016/j.enggeo.2009.08.010 ↗
16. Parsons R, Milburn J. Engineering behaviour of stabilized soils. In: Geomaterials 2003 – soils, geology, and foundations, vol. §837. Transportation Research Record, 2003. p. 20–29.10.3141/1837-03 ↗
17. Effectiveness of portland cement and lime in stabilizing clay soils10.3141/1652-28 ↗
18. Rapid chemical stabilization of soft clay soils10.3141/2026-05 ↗
19. Influence of soil grading on the characteristics of cement stabilised soil compacts
20. Strength and elastic properties of stabilized mud block masonry using cement-soil mortars10.1061/(ASCE)0899-1561(2006)18:3(472) ↗
21. Rogers C, Glendinning S. Modification of clay soils using lime. In: Lime stabilisation: proceedings of the seminar held at Loughborough University Civil & Building Engineering Department on 25 September, Amer Society of Civil Engineers, 1996, p. 99.10.1680/ls.25639.0010 ↗
22. Structure and strength characteristics of compacted clay10.1061/JSFEAQ.0000229 ↗
23. Stabilization of clay soils with nontraditional additives10.3141/1819b-10 ↗
24. Strength and erosion characteristics of earth blocks and earth block masonry10.1061/(ASCE)0899-1561(2004)16:5(497) ↗