Pseudo-static cyclic loading comparison of reinforced masonry walls strengthened with FRCM or NSM FRP
Source abstract
Abstract
Abstract Fiber reinforced polymer (FRP) composites have demonstrated poor performance in high temperature environments where the glass transition temperature of the resin is exceeded and this justifies the need to examine alternative strengthening techniques such as near surface mounted (NSM) reinforcement with cementitious adhesive or fabric-reinforced cementitious matrix (FRCM) systems. Evaluation of pseudo-static cyclic performance of these strengthening systems is of high interest. In this study, twelve reinforced masonry walls were strengthened in out-of-plane direction using FRCM composite or NSM with cementitious adhesive that were built as a part of this study. FRCM strengthening composite materials consisted of one or two plies of carbon or PBO (polyparaphenylene benzobisoxazole) fabric embedded in cementitious mortar. The NSM technique consisted of carbon or glass bar(s) installed in slots that had been grooved into the masonry tension surface. For all these specimens, a constant mild steel reinforcement ratio (ρ) was used in fully grouted walls. These simply supported walls were tested under out-of-plane constant-amplitude displacement cycles. The key parameters for this investigation were bond pattern (stack and running) and the type and amount of fabric/NSM product. The behavior of the specimens is discussed with emphasis on the load deflection response, flexural capacity, energy dissipation, stiffness degradation, and ductility index. The test results indicated that the behavior of the slender (i.e. non-arching) reinforced masonry walls was significantly dependent on the type of fiber used. The maximum flexural enhancement was found to be 97% and 75%, and the dissipated energy of the specimen with stack bond pattern was increased by 38% and 62% for masonry walls strengthened with FRCM and NSM system, respectively, compared to the control specimen. Different modes of failure occurred in the strengthened reinforced walls, including crushing of concrete block, as well as a debonding of NSM bar or fabric sheet from the masonry substrate and slippage of fabric within the cementitious matrix.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Masonry and Concrete Structural Analysis · Structural Behavior of Reinforced Concrete · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. State-of-the-art report on seismic performance of unreinforced masonry buildings10.1061/(ASCE)0733-9445(1994)120:1(230) ↗
2. Evaluation of out-of-plane stability of unreinforced masonry walls subjected to seismic excitation10.1080/13632460309350476 ↗
3. A history of reinforced masonry construction designed to resist earthquakes: 1755–190710.1193/1.1585260 ↗
4. M. Yoshimura and K. Meguro, Proposal of retrofitting promotion system for low earthquake-resistant structures in earthquake prone countries, in Proceedings on 13th World Conference on Earthquake Engineering, Vancouver, Canada, 2004.
5. Out-of-plane behavior of brick masonry walls strengthened with fiber composites
6. FRP strengthening of URM walls subject to out-of-plane loads
7. Z. Al-Jaberi, J. Myers, and M. ElGawady, Flexural capacity of out-of-plane reinforced masonry walls strengthened with externally bonded(EB) FRP, Presented at the 7th International Conference on Advanced Composite Materials in Bridges and Structures Vancouver, British Columbia, Canada, 2016.
8. Flexural displacement response of NSM FRP retrofitted masonry walls10.1016/j.conbuildmat.2012.06.065 ↗
9. Z. Al-Jaberi, J. J. Myers, and M. ElGawady, Influence of Near-Surface Mounted (NSM) FRP on the Out-of-Plane Behavior of Reinforced Masonry Walls, Presented at the 12th North American Masonry Conference, 2015.10.14455/ISEC.res.2015.228 ↗
10. Modified cement-based adhesive for near-surface mounted CFRP strengthening system10.1016/j.conbuildmat.2016.07.147 ↗
11. Z. Al-Jabari, J. J. Myers, and M. ElGawady, Out-of-plane strengthening of reinforced masonry walls using near-surface mounted (NSM) FRP Bars with epoxy and cementitious materials, Advanced Composites in Construction, ACIC, 2015, pp. 195–200.
12. K. Soudki and T. Alkhrdaji, Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures (ACI 440.2 R-02), in Structures Congress 2005: Metropolis and Beyond, 2005, pp. 1–8.10.1061/40753(171)159 ↗
13. Flexural and shear strengthening of un-reinforced masonry with FRP bars10.1016/j.compscitech.2005.04.042 ↗
14. Strengthening with FRP bars of URM walls subject to out-of-plane loads10.1016/j.conbuildmat.2005.06.047 ↗
15. In-situ and laboratory based out-of-plane testing of unreinforced clay brick masonry walls strengthened using near surface mounted twisted steel bars10.1016/j.conbuildmat.2012.04.087 ↗
16. Fabric-reinforced cementitious matrix: a promising strengthening technique for concrete structures10.1016/j.conbuildmat.2016.11.125 ↗
17. Out-of-plane strengthening of URM walls with fabric-reinforced-cementitious-matrix (FRCM)
18. In-plane and out-of-plane testing of unreinforced masonry walls strengthened using polymer textile reinforced mortar10.1016/j.engstruct.2016.03.041 ↗
19. Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: out-of-plane cyclic loading10.1617/s11527-007-9226-0 ↗
20. Experimental and analytical study to evaluate the effectiveness of an in-plane reinforcement for masonry walls using GFRP meshes10.1016/j.conbuildmat.2015.04.014 ↗
21. In-plane behaviour of tuff masonry strengthened with inorganic matrix–grid composites10.1016/j.compositesb.2012.09.068 ↗
22. ACI549.4R-13, Guide to design and construction of externally bonded fabric-reinforced cementitious matrix (FRCM) systems for repair and strengthening concrete and masonry structures, 2013.
23. Textile-reinforced mortar versus FRP as strengthening material for seismically deficient RC beam-column joints10.1061/(ASCE)CC.1943-5614.0000222 ↗
24. AC434, Proposed acceptance criteria for masonry and concrete strengthening using fiber-reinforced cementitious matrix (FRCM) composite system, 2011.
25. Bond between near-surface mounted fiber-reinforced polymer rods and concrete in structural strengthening
26. A. Said and M. Nehdi, Performance of structural concrete frames reinforced with GFRP grid, in Thirteenth world conference on earthquake engineering, 2004.
27. M. ElGawady, P. Lestuzzi, and M. Badoux, Retrofitting of masonry walls using shotcrete, in Proceedings of NZSEE 2006 conference, New Zealand, 2006.
28. Experimental investigation of cyclic behavior of concrete-filled fiber reinforced polymer tubes10.1061/(ASCE)1090-0268(2005)9:3(263) ↗
29. MSJC, Building code requirements for masonry structures. ACI 530-13/ASCE 5-13, TMS 402-13, 2013.
30. G. Hart, R. Englekirk, and W. Hong, Structural Component Model of Flexural Walls, in Proceedings of the 4th Meeting of the Joint Technical Coordinating Committee on Mas-onry Research US-J apan Coordinated Earthquake Research Program, San Diego, Califor—knaafisenxn 13am airmen 1997sE, pp. 39–47, 1988.
31. Experimental investigation of in-plane cyclic response of unbonded posttensioned masonry walls10.1061/(ASCE)ST.1943-541X.0001450 ↗
32. Lateral load response of high performance fiber reinforced concrete beam–column joints10.1016/j.conbuildmat.2005.01.007 ↗
33. Flexural behavior of reinforced concrete (RC) beams retrofitted with hybrid fiber reinforced polymers (FRPs) under sustaining loads10.1016/j.compstruct.2010.07.013 ↗
34. Priestley · 1996
35. Experimental evaluation of energy dissipation and viscous damping of repaired and strengthened RC columns with CFRP jacketing under biaxial load10.1016/j.engstruct.2017.05.021 ↗