Mesoporous silica material MCM-41: Novel additive for warm mix asphalts
Source abstract
Abstract
Abstract This study evaluates the impact of a new generation additive MCM-41 saturated with water on the asphalt foaming. MCM-41 is a mesoporous silica material which is produced in the process of synthesis from the fly ash. Experimental design included the assessment of reference asphalt specimens as well as asphalt specimens prepared with addition of MCM-41 material from 1.5 to 4 wt%. The mesoporous silica material used in this research featured a high specific surface area and a mesopores volume of 1134 m2/g and 0.980 cm3/g, respectively. The assessment of asphalt specimens was performed in terms of dynamic viscosity as a function of time (measured after 30 and 45 min of mixing) and temperature (135 °C and 160 °C). The most significant decrease in viscosity was observed for asphalt specimens prepared with 3 wt% concentration of MCM-41 material. The results presented in this paper suggest that MCM-41 mesoporous silica material can be more effective additive to warm mix asphalts (WMA) when compared to other currently used agents (zeolites, waxes, etc.). Concurrently, synthesis of MCM-41material based on the waste materials such as fly ash is environmentally friendly and economically feasible. These results have initiated another research project which includes a comprehensive mechanical and chemical assessment of different asphalts modified with MCM-41 additive and mechanical evaluation of corresponding WMA to investigate the optimal MCM-41 content.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Asphalt Pavement Performance Evaluation · Concrete and Cement Materials Research · Polymer Nanocomposites and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. Warm mix asphalt: an overview10.1016/j.jclepro.2011.11.053 ↗
2. Warm-mix asphalt pilot project in Connecticut10.3141/2294-12 ↗
3. Comparative evaluation and modification of laboratory compaction methods of road base mixtures manufactured in low-emission CIR technology with foamed bitumen and bitumen emulsion10.1016/j.proeng.2017.02.066 ↗
4. P. Jaskuła, Influence of compaction effectiveness on interlayer bonding of asphalt layers, in: The 9th International Conference Environmental Engineering, Vilnius, Lithuania, 2014.10.3846/enviro.2014.158 ↗
5. Evaluation of natural zeolite as warm mix asphalt additive and its comparison with other warm mix additives10.1016/j.conbuildmat.2013.02.026 ↗
6. A review of the application of zeolite materials in Warm Mix Asphalt technologies10.3390/app7030293 ↗
7. Synthesis of zeolite A using sewage sludge ash for application in warm mix asphalt10.1016/j.jclepro.2017.10.005 ↗
8. Charakterystyka zeolitów i ich zastosowanie jako adsorbentów substancji ropopochodnych
9. Effect of zeolite properties on asphalt foaming10.1016/j.conbuildmat.2017.02.054 ↗
10. Properties of the warm mix asphalt involving clinoptilolite and Na-P1 zeolite additives10.1016/j.conbuildmat.2016.03.188 ↗
11. Treating marginal aggregates and soils with foamed asphalt, proceedings of the association of asphalt paving technologists,
12. Application of synthetic wax for improvement of foamed bitumen10.1016/j.conbuildmat.2015.02.060 ↗
13. Evaluation of compactability and mechanical properties of bituminous mixes with warm additives10.1016/j.conbuildmat.2010.11.024 ↗
14. Influence of selected WMA additives on viscoelastic behaviour of asphalt mixes and pavements
15. Correlation between rheology and chemical composition of aged polymer-modified asphalts10.1016/j.conbuildmat.2014.03.043 ↗
16. Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland10.1080/14680629.2016.1159245 ↗
17. Influence of bitumen chemical composition and ageing on pavement performance10.3846/bjrbe.2015.12 ↗
18. B. Lai, C. Barros, H. Yin, Investigation of rheological behaviour of asphalt binder modified by the Advera additive, in: Poro-Mechanics IV: Fourth Biot Conference on Poromechanics, New York, United States, 2009.
19. J.S. Beck, U.S. Patent 5, 057, 296, 1991.
20. A facile preparation of palladium Schiff base complex supported into MCM-41 mesoporous and its catalytic application in Suzuki and Heck reactions10.1007/s10934-016-0154-7 ↗
21. Heteropolyacids anchored on amino-functionalized MCM-41 and SBA-15 and its application to the ethanol conversion reaction10.1007/s10973-016-5534-3 ↗
22. Synthesis and application of the MCM-41 and SBA-15 as matrices for in vitro efavirenz release study10.1016/j.jddst.2015.11.008 ↗
23. Controlled size synthesis and application of nanosphere MCM-41 as potent adsorber of drugs: a novel approach to new antidote agent for intoxication10.1016/j.micromeso.2015.04.002 ↗
24. MCM-41 mesoporous silica sheet with ordered perpendicular nanochannels for protein delivery and the assembly of Ag nanoparticles in catalytic applications10.1016/j.micromeso.2015.06.023 ↗
25. Synthesis of a graphene/polyaniline/MCM-41 nanocomposite and its application as a supercapacitor10.1039/c3nj00108c ↗
26. Fly ash-derived MCM-41 as a low-cost silica support for polyethyleneimine in post-combustion CO2 capture10.1016/j.jcou.2017.09.015 ↗
27. Brunauer · J. Am. Chem. Soc. · 1938 · 60 · 30910.1021/ja01269a023 ↗
28. Barrett · J. Am. Chem. Soc. · 1951 · 73 · 37310.1021/ja01145a126 ↗
29. Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report)10.1515/pac-2014-1117 ↗
30. Co-modified MCM-41 as an effective adsorbent for levofloxacin removal from aqueous solution: optimization of process parameters, isotherm, and thermodynamic studies10.1007/s11356-016-8262-0 ↗
31. Surface area and pore texture of catalysts10.1016/S0920-5861(98)00050-9 ↗