Pozzolanic reaction on alkali-activated Class F fly ash for ambient condition curable structural materials
Source abstract
Abstract
Abstract Despite considerable efforts focused on the utilization of industrial wastes, the application of low-calcium fly ash to the construction industry is limited to the partial substitution to ordinary Portland cement. High-temperature curing is a method via which fly ash can be completely utilized as an alkali-activated construction material; however, additional energy is required. In this study, the dual reaction of alkali activation and the pozzolanic reaction was proposed to manufacture ambient-condition-curable structural mortars. For this purpose, calcium hydroxide was used in fly ash activated by sodium hydroxide and sodium silicate solutions. A series of experiments, including compressive strength tests, X-ray diffraction, thermogravimetric analysis, heat of reaction, and mercury intrusion porosimetry, were conducted. The continuous pozzolanic reaction on the pre-formulated geopolymeric skeleton was found to significantly enhance the material properties. By the addition of silica fume and a 7:3 mixture of sodium hydroxide and sodium silicate solutions, the material strength increased to greater than 60 MPa at 56 days. The added silica fume as well as the reduced alkali content of the solution enhanced the reactions due to the active participation of the calcium ion supplied by the added hydrated lime in a high pH environment.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Magnesium Oxide Properties and Applications · Recycling and utilization of industrial and municipal waste in materials production
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (72)
Show source-provided references
1. Towards sustainable concrete10.1038/nmat4930 ↗
2. Supplementary cementitious materials to mitigate greenhouse gas emissions from concrete: can there be too much of a good thing?10.1016/j.jclepro.2018.01.008 ↗
3. Sustainable cement production—present and future10.1016/j.cemconres.2011.03.019 ↗
4. Global strategies and potentials to curb CO2 emissions in cement industry10.1016/j.jclepro.2012.10.049 ↗
5. High-volume use of limestone in ultra-high performance fiber-reinforced concrete for reducing cement content and autogenous shrinkage10.1016/j.conbuildmat.2019.04.091 ↗
6. Effect of slag content and activator dosage on the resistance of fly ash geopolymer binders to sulfuric acid attack10.1016/j.cemconres.2018.06.011 ↗
7. Pore solution composition of alkali-activated slag/fly ash pastes10.1016/j.cemconres.2018.10.010 ↗
8. Alkali-activated materials10.1016/j.cemconres.2017.02.009 ↗
9. Geopolymers and related alkali-activated materials10.1146/annurev-matsci-070813-113515 ↗
10. Natural pozzolan based geopolymers: A review on mechanical, microstructural and durability characteristics10.1016/j.conbuildmat.2018.09.191 ↗
11. Direct electric curing of alkali-activated fly ash concretes: a tool for wider utilization of fly ashes10.1016/j.jclepro.2016.05.098 ↗
12. Microstructure and phase evolution of alkali-activated steel slag during early age10.1016/j.conbuildmat.2019.01.213 ↗
13. Utilization of unprocessed steel slag as fine aggregate in normal- and high-strength concrete10.1016/j.conbuildmat.2019.01.178 ↗
14. Experimental methods to determine the feasibility of steel slags as supplementary cementitious materials10.1016/j.conbuildmat.2019.01.196 ↗
15. Fly, ash-based geopolymers containing added silicate waste. A review10.1016/j.ceramint.2017.07.221 ↗
16. Influence of processing temperature on the reaction product and strength gain in alkali-activated fly ash10.1016/j.cemconcomp.2018.10.010 ↗
17. Benefit-cost analysis model of using class F fly ash-based green cement in masonry units10.1016/j.jclepro.2018.06.229 ↗
18. Thermal properties of novel binary geopolymers based on metakaolin and alternative silica sources10.1016/j.clay.2015.10.005 ↗
19. Can Portland cement be replaced by low-carbon alternative materials? A study on the thermal properties and carbon emissions of innovative cements10.1016/j.jclepro.2018.02.138 ↗
20. Chemical and freeze–thaw resistance of fly ash-based inorganic mortars10.1016/j.fuel.2013.04.070 ↗
21. Geopolymer concrete: a review of some recent developments10.1016/j.conbuildmat.2015.03.036 ↗
22. Effect of nano-silica on the chemical durability and mechanical performance of fly ash based geopolymer concrete10.1016/j.ceramint.2018.04.009 ↗
23. Stabilization/solidification of hazardous and radioactive wastes with alkali-activated cements10.1016/j.jhazmat.2006.05.008 ↗
24. Microstructural characterization of alkali-activation of six Korean Class F fly ashes with different geopolymeric reactivity and their zeolitic precursors with various mixture designs10.1007/s12205-015-0132-7 ↗
25. Effect of silica fume on the mechanical properties of fly ash based-geopolymer concrete10.1016/j.ceramint.2015.10.084 ↗
26. The effects of Na2O/SiO2 molar ratio, curing temperature and age on compressive strength, morphology and microstructure of alkali-activated fly ash-based geopolymers10.1016/j.cemconcomp.2011.03.006 ↗
27. Strength enhancement of alkaline activated fly ash cured at ambient temperature by delayed activation of substituted OPC10.1016/j.conbuildmat.2016.06.111 ↗
28. Mechanical properties of ambient cured one-part hybrid OPC-geopolymer concrete10.1016/j.conbuildmat.2018.07.160 ↗
29. Effect of calcium aluminate cement on geopolymer concrete cured at ambient temperature10.1016/j.conbuildmat.2018.09.204 ↗
30. Geopolymers: inorganic polymeric new materials10.1007/BF01912193 ↗
31. The effect of ionic contaminants on the early-age properties of alkali-activated fly ash-based cements10.1016/S0008-8846(01)00724-4 ↗
32. Reaction mechanisms in the geopolymeric conversion of inorganic waste to useful products10.1016/j.jhazmat.2006.02.044 ↗
33. Opc-fly ash cementitious systems: study of gel binders produced during alkaline hydration10.1007/s10853-006-0585-7 ↗
34. Microstructural and compositional change of NaOH-activated high calcium fly ash by incorporating Na-aluminate and co-existence of geopolymeric gel and C-S–H(I)10.1016/j.cemconres.2012.02.002 ↗
35. Microanalysis of calcium silicate hydrate gel formed within a geopolymeric binder10.1023/A:1025904905176 ↗
36. Influence of calcium compounds on the mechanical properties of fly ash geopolymer pastes10.1016/j.jhazmat.2008.12.121 ↗
37. Investigation into the effect of calcium on the existence form of geopolymerized gel product of fly ash based geopolymers
38. Compressive strength and microstructure of fly ash based geopolymer blended with silica fume under thermal cycle10.1016/j.cemconcomp.2017.01.009 ↗
39. Acceleration of intended pozzolanic reaction under initial thermal treatment for developing cementless fly ash based mortar10.3390/ma10030225 ↗
40. Intensified pozzolanic reaction on kaolinite clay-based mortar10.3390/app7050522 ↗
41. Enhancement of material properties of lime-activated slag mortar from intensified Pozzolanic reaction and pore filling effect10.3390/su10114290 ↗
42. ASTM C618–00, Standard, specification for coal fly ash and raw or calcined natural pozzolan for use in concrete, ASTM International, West 2013 Conshohocken, PA 4
43. ISO 679, Cement–test methods–determination of strength,, International Organization for Standardization, Geneva, Switzerland, 2009, p. 29.
44. Characterization of natural pozzolan-based geopolymeric binders10.1016/j.cemconcomp.2014.06.010 ↗
45. ASTM C305–14, Standard, practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency, ASTM International, West 2014 Conshohocken, PA 3
46. ASTM C109 / C109M–16a, Standard test method for compressive strength of hydraulic cement mortars (Using 2-in. or [50-mm] cube specimens), ASTM 2016 International, West Conshohocken, PA 10
47. Report of TC 238-SCM: hydration stoppage methods for phase assemblage studies of blended cements—results of a round robin test10.1617/s11527-018-1237-5 ↗
48. Mercury porosimetry: An inappropriate method for the measurement of pore size distributions in cement-based materials10.1016/S0008-8846(00)00370-7 ↗
49. Ink-bottle effect in mercury intrusion porosimetry of cement-based materials10.1006/jcis.2001.7962 ↗
50. Scrivener · 2016
51. The effect of superabsorbent polymer on various scale of pore structure in ultra-high performance concrete10.1016/j.conbuildmat.2018.03.193 ↗
52. Mechanical properties, drying and autogenous shrinkage of blast furnace slag activated with hydrated lime and gypsum10.1016/j.cemconcomp.2010.01.004 ↗
53. Characterization of mullite in silicoaluminous fly ash by XRD, TEM, and 29Si MAS NMR10.1016/S0008-8846(99)00226-4 ↗
54. Taylor · 1997
55. The structure and stoichiometry of C-S-H10.1016/j.cemconres.2004.04.035 ↗
56. Review of Synthesis and Properties of Tobermorite, C-S-H(I), and C-S-H Gel10.1111/j.1151-2916.1975.tb11478.x ↗
57. Alkali-activated fly ash/slag cements: Strength behaviour and hydration products10.1016/S0008-8846(00)00298-2 ↗
58. Microstructural investigation of heat-treated ultra-high performance concrete for optimum production10.3390/ma10091106 ↗
59. A critical appraisal of the role of clay mineralogy in lime stabilization10.1007/s40891-015-0009-3 ↗
60. Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram Na2O–CaO–Al2O3–SiO2–H2O10.1016/j.cemconres.2011.05.006 ↗
61. Compressive strength and microstructural characteristics of class C fly ash geopolymer10.1016/j.cemconcomp.2009.11.003 ↗
62. Effect of calcium silicate sources on geopolymerisation10.1016/j.cemconres.2007.11.001 ↗
63. Pore solution chemistry of alkali-activated ground granulated blast-furnace slag10.1016/S0008-8846(98)00212-9 ↗
64. Role of slag in microstructural development and hardening of fly ash-slag geopolymer10.1016/j.cemconres.2012.10.004 ↗
65. Yip · 2004
66. The evolution of strength and crystalline phases for alkali-activated ground blast furnace slag and fly ash-based geopolymers10.1016/j.cemconres.2009.10.010 ↗
67. The coexistence of geopolymeric gel and calcium silicate hydrate at the early stage of alkaline activation10.1016/j.cemconres.2004.10.042 ↗
68. Mechanism of polysialation in the incorporation of zirconia into fly ash-based geopolymers10.1021/ie990929w ↗
69. Microstructural investigation of a silica fume–cement–lime mortar10.1016/S0958-9465(02)00006-9 ↗
70. Mechanisms of hydration reactions in high volume fly ash pastes and mortars10.1016/0958-9465(90)90004-H ↗
71. Influence of steam curing on the pore structures and mechanical properties of fly-ash high performance concrete prepared with recycled aggregates10.1016/j.cemconcomp.2016.05.010 ↗
72. On drying shrinkage in alkali-activated concrete: Improving dimensional stability by aging or heat-curing10.1016/j.cemconres.2016.10.003 ↗