journal article·2020-03

Comparative study of carbide slag autoclaved aerated concrete (AAC) manufactured under thermal oven and microwave pre-curing process: Foaming course, rough body strength and physic-mechanical properties

Lixiong Cai, Tao Tang, Miao Liu, Dingkun Xie

Publisher page

Abstract

Abstract The substitution of carbide slag to quicklime in carbide slag autoclaved aerated concrete (AAC) preparation caused significant side-effect on stable formation of porosity structure in pre-curing process. With objective of regulating slurry foaming course and rough body strength development during pre-curing process of carbide slag AAC production, microwave heating technology was introduced to control the slurry temperature accurately, and regulate the foaming and thickening process ulteriorly. Therefore, the discrepancy between conventional and microwave pre-curing process in mould and energy were discussed qualitatively. Moreover, to figure out the superiority and effect law of microwave pre-curing process with different curing temperature, the comparison between conventional and microwave pre-curing process on slurry foaming course, rough body development and physic-mechanical properties were investigated. The discrepancy analysis illuminated that with transition from thermal oven curing to microwave pre-curing, mixing water and mould should be changed from warm water (>50 °C) and metal mould to normal temperature water and microwave penetrable mould respectively, meanwhile, the theoretical energy requirement was significantly reduced. Otherwise, the experimental results indicated that microwave pre-curing technology effectively accelerate the gas foaming rate in early stage and increased ultimate foaming ratio with increasing of curing temperature. However, the gradient temperature of microwave pre-curing between foaming and thickening stage should not exceed 20 °C, so as to avoid the temperature stress on bonding surface of rough body and container, which may cause ring collapse. Moreover, rough body strength development was improved with utilizing of microwave pre-curing technology, the pre-curing duration could be shortened by 0.5–1 h relative to thermal oven pre-curing process. Furthermore, the physic-mechanical performance of thermal oven and microwave pre-cured carbide slag AAC specimens were comparable. Overall, the results indicated that microwave pre-curing technology has great potential to be an alternative curing method for manufacturing carbide slag AAC.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovations in Concrete and Construction Materials · Concrete and Cement Materials Research · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Hygric thermal and durability properties of autoclaved aerated concrete10.1016/j.conbuildmat.2012.12.036 ↗
2. Understanding autoclaved aerated concrete
3. Relations between structure and mechanical properties of autoclaved aerated concrete10.1016/0008-8846(79)90049-8 ↗
4. Structure and properties of aerated concrete: a review10.1016/S0958-9465(00)00016-0 ↗
5. Jineng · 1992
6. The slurry and physical-mechanical performance of autoclaved aerated concrete with high content solid wastes: Effect of grinding process10.1016/j.conbuildmat.2019.05.107 ↗
7. Technologia Autoklawizowanego Betonu Komòrkowego
8. Synthesis and microstructure analysis of autoclaved aerated concrete with carbide slag addition
9. Effect of binding materials on carbide slag based high utilization solid-wastes autoclaved aerated concrete (HUS-AAC): slurry, physic-mechanical property and hydration products10.1016/j.conbuildmat.2018.08.115 ↗
10. Hitchcock · 2004 · 1
11. Kumar · 2014 · 3
12. Microwave processing of materials10.1146/annurev.ms.26.080196.001503 ↗
13. A.C. Metaxas, R.J. Meredith, Industrial microwave heating London: Peregrinus on behalf of the Institution of Electrical Engineers, 1983.
14. Fundamentals and applications of microwave energy in rock and concrete processing – a review10.1016/j.applthermaleng.2019.113751 ↗
15. Applications of microwave energy in cement and concrete – a review10.1016/j.rser.2014.05.054 ↗
16. Response of alkali activated fly ash mortars to microwave curing10.1016/j.cemconres.2010.08.010 ↗
17. Microwave curing technique in concrete manufacture10.1016/0008-8846(87)90103-7 ↗
18. Thermal acceleration of Portland cement mortars with microwave energy10.1016/0008-8846(91)90174-G ↗
19. S. Shi, Y. Bai, H. Li, et al. Comparative study of alkali-activated fly ash manufactured under pulsed microwave curing and thermal oven curing, 4th International Conference on the Durability of Concrete Structures, 2014.10.5703/1288284315483 ↗
20. Microwave curing of Portland cement concrete: experimental results and feasibility for practical applications10.1016/0950-0618(94)00001-I ↗
21. Very high early strength of microwave cured concrete10.1016/0008-8846(94)00121-E ↗
22. Determination of optimal process for microwave curing of concrete10.1016/S0008-8846(97)00015-X ↗
23. Microwave curing at operating frequency of 2.45 GHz of Portland cement paste at early-stage using a multimode cavity: experimental and numerical analysis on heat transfer characteristics10.1016/j.icheatmasstransfer.2010.09.001 ↗
24. Development of compressive strength of cement paste under accelerated curing by using a continuous microwave thermal processor10.1016/j.msea.2007.03.035 ↗
25. A novel rapid microwave-thermal process for accelerated curing of concrete: prototype design, optimal process and experimental investigations10.1016/j.conbuildmat.2016.07.084 ↗
26. Microwave Curing Techniques for Manufacturing Alkali-activated Fly Ash, 34th Annual Cement and Concrete
27. Shi · 2017
28. Effect of microwave curing conditions on high strength concrete properties10.1016/j.egypro.2014.07.128 ↗
29. Microwave curing parameters of in-situ concrete repairs10.1016/j.conbuildmat.2016.03.007 ↗
30. Fast estimating concrete strength method applying microwave autoclave curing technology