journal article·2020-11

Effects of pre-soaked zeolite and CaO-based expansive agent on mechanical properties and autogenous deformation of early-age concrete

Haitao Zhao, Jinghao Li, Gaoyang Sun, Jianhua Jiang, Weihong Xuan, Yuzhi Chen, Qian Tian, Jiaping Liu

Publisher page

Abstract

Abstract High-performance concrete (HPC) is prone to cracking at an early age due to the large autogenous shrinkage (AS), which severely weakens the durability of the concrete structure. CaO-based expansive agent (CEA) is widely utilized to compensate for the AS of HPC, but CEA cannot achieve its potential expansion in HPC due to a low water to binder ratio, resulting in an incomplete hydration, and a sharp and substantial retraction after initial expansion. Pre-soaked zeolite can be introduced as internal curing (IC) agent to reduce the AS of HPC owing to the IC water released from zeolite. According to the AS-reduction mechanism of CEA and zeolite, a synergistic mechanism can be achieved by the combination use of CEA and zeolite in HPC. However, a comprehensive understanding of the effects of the combination use of zeolite and CEA on the mechanical properties and autogenous deformation of concrete is still lacking. Therefore, the influence of zeolite and CEA addition on mechanical properties and autogenous deformation were investigated experimentally. The investigation results showed that the zeolite addition weakened the mechanical properties of concrete while the CEA addition had the opposite effect. The internal relative humidity in concrete was significantly improved with zeolite and CEA incorporation. The IC water released from zeolite could not only enhance the expansion efficiency at an early age but also greatly reduce the retraction at the later age. The results exhibited an obvious synergistic mechanism with the combination use of zeolite and CEA on AS mitigation, which is of great benefit in AS-induced cracking control.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete Properties and Behavior · Concrete and Cement Materials Research · Drilling and Well Engineering

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. Modified Lucas-Washburn function of capillary transport in the calcium silicate hydrate gel pore: A coarse-grained molecular dynamics study10.1016/j.cemconres.2020.106166 ↗
2. Molecular dynamics study on the structure and dynamics of NaCl solution transport in the nanometer channel of CASH gel10.1021/acssuschemeng.8b02126 ↗
3. Investigation on the poor fluidity of electrically conductive cement-graphite paste: Experiment and simulation10.1016/j.matdes.2019.107679 ↗
4. Experimental and molecular dynamics studies on the transport and adsorption of chloride ions in the nano-pores of calcium silicate phase: the influence of calcium to silicate ratios10.1016/j.micromeso.2017.07.024 ↗
5. Experimental investigation on the autogenous shrinkage of steam cured ultra-high performance concrete10.1016/j.conbuildmat.2017.11.172 ↗
6. Shrinkage reduction of high strength fiber reinforced cementitious composites (HSFRCC) with various water-to-binder ratios10.1016/j.cemconcomp.2011.03.009 ↗
7. Autogenous shrinkage of high-strength concrete containing silica fume under drying at early ages10.1016/j.cemconres.2004.06.006 ↗
8. Early-age shrinkage development of ultra-high-performance concrete under heat curing treatment10.1016/j.conbuildmat.2016.11.024 ↗
9. D. P. Bentz, K. A. Snyder, P. E. Stutzman, Microstructural modeling of self-desiccation during hydration, Lund, Sweden, in: B. Persson, G. Fagerlund (Eds.), Proceeding of an Int. Research Seminar Self-Desiccation and Its Importance in Concrete Technology (1997) 132-140.
10. Research on Bonding and Shrinkage Properties of SHCC-Repaired Concrete Beams
11. Experimental and theoretical analysis on coupled effect of hydration, temperature and humidity in early-age cement-based materials10.1016/j.ijheatmasstransfer.2019.118784 ↗
12. Estimation of cracking risk of concrete at early age based on thermal stress analysis10.1007/s10973-011-1512-y ↗
13. Early-age behavior and cracking resistance of high-strength concrete reinforced with Dramix 3D steel fiber10.1016/j.conbuildmat.2018.10.125 ↗
14. Effectiveness Protection Performance of an Internal Blending Organic Corrosion Inhibitor for Carbon Steel in Chloride Contaminated Simulated Concrete Pore Solution10.3151/jact.18.116 ↗
15. Ionic transport features in concrete composites containing various shaped aggregates: a numerical study10.1016/j.compstruct.2017.03.088 ↗
16. Experimental and numerical study on chloride transport in cement mortar during drying process
17. Investigation of moisture transport in cement-based materials using low-field nuclear magnetic resonance imaging
18. Influence of CaO-Based expansive agent on the deformation behavior of high performance concrete
19. Analysis technique for autogneous shrinkage in high performance concrete with mineral and chemical admixtures10.1016/j.conbuildmat.2012.02.005 ↗
20. Effects of nano and micro size of CaO and MgO, nano-clay and expanded perlite aggregate on the autogenous shrinkage of mortar10.1016/j.conbuildmat.2015.02.032 ↗
21. Combined effect of expansive and shrinkage reducing admixtures to obtain stable and durable mortars10.1016/j.cemconres.2004.11.021 ↗
22. Combined effect of expansive and shrinkage reducing admixtures to control autogenous shrinkage in self-compacting concrete10.1016/j.conbuildmat.2013.11.033 ↗
23. Research on performance improvement of expansive agent with internal curing agent SAP and its action mechanism
24. Influence of a combination of expansive and shrinkage-reducing admixtures on autogenous deformation and self-stress of silica fume high-performance concrete10.1016/j.conbuildmat.2010.06.033 ↗
25. Several issues in the manufacture of shrinkage-compensating concrete using expansive agent
26. Internal curing by super absorbent polymers (SAP)-effects on material properties of self-compacting fibre-reinforced high performance concrete. Volume changes of hardening concrete, in
27. Super absorbing polymers as an internal curing agent for mitigation of early-age cracking of high-performance concrete bridge decks10.1016/j.conbuildmat.2010.06.063 ↗
28. Efficiency of lightweight aggregates for internal curing of high strength concrete to eliminate autogenous shrinkage10.1007/BF02482108 ↗
29. Effect of prewetting degree of ceramsite on the early-age autogenous shrinkage of lightweight aggregate concrete10.1016/j.conbuildmat.2015.08.102 ↗
30. Internal curing of high-performance concrete with pre-soaked fine lightweight aggregate for prevention of autogenous shrinkage cracking10.1016/j.cemconres.2008.02.001 ↗
31. Applications of natural zeolite to construction and building materials in China10.1016/j.conbuildmat.2005.01.013 ↗
32. Shrinkage of internal cured high strength engineered cementitious composite with pre-wetted sand-like zeolite10.1016/j.conbuildmat.2016.12.182 ↗
33. Investigation on the potential utilization of zeolite as an internal curing agent for autogenous shrinkage mitigation and the effect of modification10.1016/j.conbuildmat.2018.12.001 ↗
34. Reuse of hazardous electrolytic manganese residue: Detailed leaching characterization and novel application as a cementitious material
35. China Standard GB 175-2007/XG1-2009, Common portland cement, General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China, Beijing, 2009. (in Chinese)
36. ASTM C150/C150 M. Standard specification for portland cement. ASTM International, West Conshohocken, PA, 2015.
37. China Standard GB 23439-2009, Expansive agents for concrete, General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China, Beijing, 2010. (in Chinese)
38. ASTM C806-18 Standard Test Method for Restrained Expansion of Expansive Cement Mortar. ASTM International, West Conshohocken, PA, 2018.
39. ASTM C128-07. Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate. ASTM International, West Conshohocken, PA, 2007.
40. Protected paste volume in concrete: extension to internal curing using saturated lightweight fine aggregate10.1016/S0008-8846(99)00178-7 ↗
41. Mixtures proportioning for internal curing
42. ASTM C1761/ C1761M-17, Standard Specification for Lightweight Aggregate for Internal Curing of Concrete. ASTM International, West Conshohocken, PA, 2017.
43. Study on the measurement of autogenous shrinkage of high performance concrete
44. P. Gao, S. Xu, X.Chen, et al., Research on autogenous volume deformation of concrete with MgO, Constr. Build. Mater. 40 (2013) 998-1001.10.1016/j.conbuildmat.2012.11.025 ↗
45. ASTM C192/C192M-16, Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory. ASTM International, West Conshohocken, PA, 2016.
46. Effect of autogenous deformation on the cracking risk of slag cement concretes10.1016/j.cemconcomp.2010.12.003 ↗
47. Improving test methods to measure early-age autogenous shrinkage in concrete based on air cooling
48. Estimation of temperature effects on autogenous shrinkage of concrete by a new prediction model10.1016/j.conbuildmat.2012.03.005 ↗
49. Experimental study on the relationship between shrinkage and interior humidity of concrete at early age10.1680/macr.2010.62.3.191 ↗
50. Q. Tian, Y. Wang, H. Zhang, et al., In-situ monitoring of setting of concrete based on pore water pressure measurement, in: Second International Conference on Microstructural-related Durability of Cementitious Composites, Amsterdam, the Netherlands, 2012.
51. China Standard GB/T50080-2016. Standard for test method of performance on ordinary fresh concrete. Ministry of construction of the People's Republic of China, Beijing, 2003. (in Chinese)
52. ASTM C403/C403M-16, Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance. ASTM international, West Conshohocken, PA, 2016.
53. China Standard GB/T50081-2002. Standard test method of mechanical properties on ordinary concrete, Ministry of construction of the People's Republic of China, Beijing, 2002. (in Chinese)
54. ASTM C39/C39M-20, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. ASTM International, West Conshohocken, PA, 2020.
55. ASTM C496/C 496M-17, Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens. ASTM International, West Conshohocken, PA, 2017.
56. ASTM C597-16 Standard Test Method for Pulse Velocity Through Concrete. ASTM International, West Conshohocken, PA, 2016.
57. Ultrasonic pulse velocity test of concrete properties as specified in various standards10.1016/0958-9465(96)00026-1 ↗
58. Hydration and setting time of MgO-Type expansive cement10.1016/0008-8846(92)90129-J ↗
59. Effect of PVA, glass and metallic fibers and of an expansive admixtures on the cracking tendency of ultrahigh strength mortar10.1016/S0958-9465(03)00076-3 ↗
60. The effect of zeolite amount on the physical and mechanical properties of concrete
61. Interfacial interactions in lightweight aggregate concretes and their influence on the concrete strength10.1016/0958-9465(96)00002-9 ↗
62. Relation between the molecular structure and the efficiency of superabsorbent polymers (SAP) as concrete admixtures to mitigate autogenous shrinkage10.1016/j.cemconres.2012.03.011 ↗
63. Internal curing of concrete using lightweight aggregates10.1080/02726351.2016.1256360 ↗
64. The effects of nanoscale expansive agents on the mechanical peoperties of non-shrink cement-based composites: The influence of nano-MgO addition10.1016/j.compositesb.2013.06.033 ↗
65. The effect of nano-MgO on the setting time, autogenous shrinkage, microstructure and mechanical properties of high performance cement paste and mortar10.1016/j.conbuildmat.2017.08.168 ↗
66. Effect of internal curing on internal relative humidity and shrinkage of high strength concrete slabs10.1016/j.conbuildmat.2014.02.060 ↗
67. Potential for restrained shrinkage of concrete and motar