journal article·2015-08

Influence of rheology on the quality of surface finish of cement-based mortars

Jacek Kwasny, Mohammed Sonebi, Julien Plasse, Sofiane Amziane

Publisher page

Abstract

Abstract Aesthetics of concrete structures is directly related to the quality of their surface finish. The objective of this investigation was to examine the effect of rheological properties of cement-based mortars on the quality of their surface finish. The study was divided into two phases. Firstly, the influence of the mix composition of mortars, viz. the water to cement (w/c) ratio, the sand content and the superplasticiser (SP) dosage on their rheology was evaluated. Secondly, the surface finish quality was characterised and related to the rheology of the studied systems. Rheology of these materials, i.e. the yield value, was measured using a vane viscometer. The quality of the surface finish was assessed by quantification of the surface air voids by analysing digital photographs of the mould finished sample surfaces. It was found that an increase in the w/c ratio and the SP content decreased the yield value, whilst the increase in the sand content had an opposite effect. When the surface quality is concerned, an increase in the yield value was found to increase the total content of the surface air voids and especially those with size smaller than 1 mm in diameter. Moreover, the analysis of the location of the surface air voids along the height of the sample revealed that with the increase in the yield value their concentration was higher in the bottom section of the analysed samples.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovations in Concrete and Construction Materials · Concrete and Cement Materials Research · Concrete Properties and Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Hurd · 2005
2. 2000
3. 2013
4. 1998
5. The Concrete Society and CONSTRUCT. Plain formed concrete finishes. Concrete Society and CONSTRUCT Technical Report 52. The Concrete Society; 1999. 50 pp.
6. Evaluating concrete surfaces using an image analysis process10.1016/j.conbuildmat.2005.01.025 ↗
7. ACI concrete terminology. Farmington Hills, MI, USA: American Concrete Institute; 2010. 81 pp.
8. CIB Working Commission W29 – Concrete Surface Finishing. Tolerances on blemishes of concrete. CIB Report No. 24. Rotterdam, Netherlands: Conseil International du Bâtiment (CIB); 1973. 8 pp.
9. Bernabeu O. Final synthesis report on task 7 – form-system and surface quality, Brite EuRam project: rational production and improved working environment through using self-compacting concrete, Contract No. BE96-3801/BRPR-CT96-0366. Brussels; 2000. 83 pp.
10. Final report of RILEM TC 188-CSC ‘Casting of self-compacting concrete’10.1617/s11527-006-9186-9 ↗
11. 2008
12. Vikan H. State of the art – quality of concrete surfaces, SINTEF report No. SBF BK A07013. SINTEF; 2007. 36 pp.
13. 2013
14. 2009
15. 2009
16. 2006
17. 2010
18. 2011
19. NBS, National building specification. Newcastle.
20. 1989
21. 1998
22. 2004
23. Blowholes in concrete surfaces
24. Voids in concrete surfaces
25. The bughole problem
26. Design and optimization of an instrument for measuring bughole rating of concrete surfaces10.1016/j.jfranklin.2010.04.004 ↗
27. Expert system applied for classifying self-compacting concrete surface finish10.1016/j.advengsoft.2013.04.005 ↗
28. Neville · 1996
29. Air-pore instability and its effect on the concrete properties
30. Mechanisms of air entrainment in concrete10.1016/j.cemconres.2004.07.026 ↗
31. Air-void stability of self-consolidating concrete
32. Martin M. Étude de la texture de la surface coffrée des parements verticaux en béton [Ph.D. thesis]. France: Université Laval, Canada and Université de Cergy-Pontoise; 2007. 198 pp.
33. 2007
34. Kolek J. Research on the vibration of fresh concrete. Conference on vibrations-compaction techniques, Reports. Budapest, Hungary; 1963. p. 61–76.
35. Tattersall · 1983
36. The effect of vibration on rheological properties of fresh concrete10.1680/macr.1988.40.143.79 ↗
37. Vibration and the rheology of fresh concrete – a further look
38. Relationship between the rheology of unvibrated fresh concrete and its flow under vibration in a vertical pipe apparatus10.1680/macr.1999.51.3.181 ↗
39. The rheology of fresh high performance concrete10.1016/0008-8846(95)00213-8 ↗
40. A unique experimental method for monitoring aggregate settlement in concrete10.1016/S0008-8846(00)00223-4 ↗
41. Schartzentruber A. Conception d’outils d’emboutissage en béton pour la mise en forme de tôles minces [Ph.D. thesis]. Cachan: Ecole Normale Supérieure; 2000. 228 pp.
42. 2000
43. Yield stress measurements with the vane10.1016/0377-0257(95)01421-7 ↗
44. Rotating vane rheometry – a review10.1016/S0377-0257(01)00095-7 ↗
45. Steady state flow of cement suspensions: a micromechanical state of the art10.1016/j.cemconres.2009.08.026 ↗
46. Measuring the flow properties of yield stress fluids10.1146/annurev.fl.24.010192.000403 ↗
47. Influence of the type of coarse lightweight aggregate on properties of semi-lightweight self-consolidating concrete10.1061/(ASCE)MT.1943-5533.0000527 ↗
48. Towards a prediction of superplasticized concrete rheology10.1007/BF02481674 ↗
49. Multi scale experimental study of concrete rheology: from water scale to gravel scale
50. From ordinary rheology concrete to self compacting concrete: a transition between frictional and hydrodynamic interactions10.1016/j.cemconres.2008.03.011 ↗
51. Spiratos · 2003
52. Rheology as a tool in concrete science: the use of rheographs and workability boxes10.1016/j.cemconres.2011.01.009 ↗
53. Golaszewski J. Correlation between rheology of superplasticized fresh mortars and fresh concretes. In: Gupta P, Holland TC, Malhotra VM, editors. Proceedings of tenth ACI international conference on recent adventures in concrete technology and sustainability issues. Seville, Spain; 2009. p. 215–36 [ACI SP-261-16].