Rheological properties of magnesium phosphate cement with different M/P ratios
Source abstract
Abstract
Abstract Magnesium phosphate cement (MPC) with unique advantages of quick setting and high early-strength has been used as grouting materials. The rheological properties of MPC, being vitally important for site operation, need to be studied further. Dead burnt magnesia (MgO) and phosphate (ADP) are the main raw materials for preparing MPC. This study measured the rheological properties with different M/P ratios, and the mechanisms of M/P ratio were studied by characterizing the zeta potential, 1H NMR relaxation signal, water film thickness, mineral changes and electrical impedance. Experimental results indicate that both the yield stress (τ0) and plastic viscosity (η) decrease firstly and then increase gradually with increasing the M/P ratio from 2.5:1 to 4.5:1. Higher M/P ratio decreases the interparticle water film thickness and accelerates the initial hydration rate remarkably, which is responsible for the change in rheological parameters. Low field NMR, TG-DTG analysis and Nyquist plots confirm the quicker initial hydration in MPC with higher M/P ratio. The change in hydration products is very slight during the rheological property measurements. Nyquist plots show that the MPC paste with lower M/P ratios has more compact microstructure and lower porosity at several hours. In a word, initial hydration rate is the most important factor influencing the rheological properties of MPC, and the separation distance among solid particles is the secondary factor.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Oxide Properties and Applications · Multiferroics and related materials · Materials Engineering and Processing
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. Dental investment or refractory material
2. Rapid setting magnesium phosphate cement for quick repair of concrete pavements-characterization and durability aspects10.1016/0008-8846(93)90090-V ↗
3. Factors influencing properties of phosphate cement-based binder for rapid repair of concrete10.1016/S0008-8846(98)00230-0 ↗
4. Property evaluation of magnesium phosphate cement mortar as patch repair material10.1016/j.conbuildmat.2009.10.039 ↗
5. Cementing mechanism of potassium phosphate based magnesium phosphate cement10.1016/j.ceramint.2012.04.083 ↗
6. Factors that affect the properties of magnesium phosphate cement10.1016/j.conbuildmat.2013.05.103 ↗
7. Experimental study on the preparation and properties of a novel foamed concrete based on magnesium phosphate cement10.1016/j.conbuildmat.2017.01.092 ↗
8. Research progresses in magnesium phosphate cement–based materials10.1061/(ASCE)MT.1943-5533.0000971 ↗
9. Surface modification of MgO substrates from aqueous exposure: an atomic force microscopy study
10. Mechanisms of k-struvite formation in magnesium phosphate cements10.1016/j.cemconres.2016.11.008 ↗
11. Properties of magnesium phosphate cement containing redispersible polymer powder10.1016/j.conbuildmat.2016.03.053 ↗
12. Laboratory evaluation of magnesium phosphate cement paste and mortar for rapid repair of cement concrete pavement10.1016/j.conbuildmat.2014.02.015 ↗
13. Leaching behaviour of magnesium phosphate cements containing high quantities of heavy metals10.1016/j.jhazmat.2009.10.077 ↗
14. Research on the preparation and properties of a novel grouting material based on magnesium phosphate cement10.1016/j.conbuildmat.2019.04.158 ↗
15. Feasibility study on sustainable magnesium potassium phosphate cement paste for 3D printing10.1016/j.conbuildmat.2019.05.053 ↗
16. Action of the combined presence of CS-Hs-PCE and triethanolamine on the performances of cement paste/mortar10.1016/j.conbuildmat.2020.121345 ↗
17. The effect of retarders on the microstructure and mechanical properties of magnesia–phosphate cement mortar10.1016/S0008-8846(00)00501-9 ↗
18. Characterization and cooling effect of a novel cement-based composite phase change material10.1016/j.solener.2020.07.083 ↗
19. Alkali-activated slag supplemented with waste glass powder: laboratory characterization, thermodynamic modelling and sustainability analysis
20. Research progresses on magnesium phosphate cement: a review10.1016/j.conbuildmat.2019.03.304 ↗
21. High-early-strength magnesium phosphate cement with fly ash
22. Effects of fly ash and quartz sand on water-resistance and salt-resistance of magnesium phosphate cement10.1016/j.conbuildmat.2015.12.154 ↗
23. Effects of metakaolin on properties and microstructure of magnesium phosphate cement10.1016/j.conbuildmat.2019.117353 ↗
24. A preliminary investigation of the properties of potassium magnesium phosphate cement-based grouts mixed with fly ash, water glass and bentonite10.1016/j.conbuildmat.2019.117501 ↗
25. Influence of fly ash and metakaolin on the microstructure and compressive strength of magnesium potassium phosphate cement paste10.1016/j.cemconres.2018.06.003 ↗
26. Coupling effects of recycled aggregate and GGBS/metakaolin on physicochemical properties of geopolymer concrete10.1016/j.conbuildmat.2019.07.311 ↗
27. Characterisation of magnesium potassium phosphate cements blended with fly ash and ground granulated blast furnace slag10.1016/j.cemconres.2015.01.015 ↗
28. The effect of ultra-fine admixture on the rheological property of cement paste10.1016/S0008-8846(00)00236-2 ↗
29. Effect of constituents on rheological properties of fresh concrete-a review10.1016/j.cemconcomp.2017.07.016 ↗
30. Influence of character of clinker on the early hydration process and rheological property of cement paste10.1016/0008-8846(85)90053-5 ↗
31. Rheological properties of cement pastes: a discussion of structure formation and mechanical property development10.1016/j.cemconres.2008.06.008 ↗
32. Hydration and rheology control of concrete for digital fabrication: Potential admixtures and cement chemistry10.1016/j.cemconres.2018.05.014 ↗
33. Effects of the addition of nanosilica on the rheology, hydration and development of the compressive strength of cement mortars10.1016/j.compositesb.2015.07.009 ↗
34. Rheological properties and the air content in fresh concrete for self-compacting high-performance concrete10.1016/j.conbuildmat.2015.07.051 ↗
35. Microhardness characteristics of high-strength cement paste and interfacial transition zone at different curing regimes10.1016/j.conbuildmat.2019.06.084 ↗
36. Roles of water film thickness and fibre factor in workability of polypropylene fibre reinforced mortar10.1016/j.cemconcomp.2018.07.014 ↗
37. Monitoring the evolution of material structure in cement pastes and concretes using electrical property measurements10.1016/j.conbuildmat.2013.08.038 ↗
38. Effect of coarse particle volume fraction on the hydraulic conductivity of fresh cement-based material10.1617/s11527-014-0311-x ↗
39. Properties of magnesium phosphate cement containing steel slag powder10.1016/j.conbuildmat.2018.11.085 ↗
40. Qiao · 2010
41. The rheology of cement during setting
42. Yodel: a yield stress model for suspensions10.1111/j.1551-2916.2005.00888.x ↗
43. Effects of particle packing density on the stability and rheology of self-consolidating concrete containing mineral admixtures10.1016/j.conbuildmat.2013.11.076 ↗
44. Coupling colloidal forces with yield stress of charged inorganic particle suspension: a review10.1002/elps.201700314 ↗
45. Application of three self-developed ECT sensors for monitoring the moisture content in sand and mortar
46. Experimental and numerical study on chloride transport in cement mortar during drying process10.1016/j.conbuildmat.2020.119655 ↗
47. Comparative life cycle assessment of reactive MgO and Portland cement production10.1016/j.jclepro.2016.07.071 ↗
48. Analytical investigation of phase assemblages of alkali-activated materials in CaO-SiO2-Al2O3 systems: the management of reaction products and designing of precursors10.1016/j.matdes.2020.108975 ↗
49. Error evaluation and correction of stray impedance during measurement and interpretation of AC impedance of cement-based materials10.1016/j.cemconcomp.2016.06.003 ↗
50. Experimental study on full-volume slag alkali-activated mortars: air-cooled blast furnace slag versus machine-made sand as fine aggregates10.1016/j.jhazmat.2020.123983 ↗
51. Equivalent circuit model for AC electrochemical impedance spectroscopy of concrete10.1016/S0008-8846(00)00400-2 ↗
52. Effect of temperature on the pore solution, microstructure and hydration products of Portland cement pastes10.1016/j.cemconres.2006.11.016 ↗
53. Clean and low-alkalinity one-part geopolymeric cement: effects of sodium sulfate on microstructure and properties10.1016/j.jclepro.2019.119279 ↗
54. Rheological properties, compressive strength, hydration products and microstructure of seawater-mixed cement pastes10.1016/j.cemconcomp.2020.103770 ↗
55. Roles of metakaolin in magnesium phosphate cement: effect of the replacement ratio of magnesia by metakaolin with different particle sizes10.1016/j.conbuildmat.2019.116675 ↗