journal article·2011-04

Properties of sintered low calcium bottom ash aggregate with clay binders

S. Geetha, K. Ramamurthy

Publisher page

Abstract

Abstract This paper focuses on the properties of sintered aggregates with low calcium bottom ash from coal fired thermal power plants using a wide range of clay binders through pelletization process. The experimental runs were designed using central composite design of response surface methodology. The aggregate was produced using a disc pelletizer. The pelletized aggregate was sintered at 800–1100 °C for 30–120 min. Sintered aggregates were tested for bulk density, 10% fines value and water absorption. The factors involved in the process are moisture content, binder, Ca(OH)2 dosage, sintering temperature and duration. It was observed that an increase in binder dosage and sintering temperature resulted in aggregates with higher 10% fines value and low water absorption. The properties of aggregates depended on the type of binder used. Aggregate with kaolinite and metakaolin binders resulted in high 10% fines value. The results indicate the potential for manufacturing high quality lightweight aggregate from bottom ash using clay binders.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Recycling and utilization of industrial and municipal waste in materials production · Glass properties and applications · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Properties and microstructure of lightweight aggregate produced from sintered sewage sludge ash10.1016/j.resconrec.2004.12.006 ↗
2. Synthetic aggregates from combustion ashes using an innovative rotary kiln10.1016/S0956-053X(00)00096-9 ↗
3. Effect of SiO2–Al2O3–flux ratio change on the bloating characteristics of lightweight aggregate material produced from recycled sewage sludge10.1016/j.jhazmat.2005.10.035 ↗
4. Development and tests of lightweight aggregate using sewage sludge for nonstructural concrete10.1016/j.conbuildmat.2005.09.009 ↗
5. A research on sintering characteristics and mechanisms of dried sewage sludge10.1016/j.jhazmat.2008.03.054 ↗
6. Utilization of lignite power generation residues for the production of lightweight aggregates10.1016/j.jhazmat.2008.06.125 ↗
7. Swelling characteristic of bentonite on pelletization and properties of fly ash aggregates10.1061/(ASCE)0899-1561(2009)21:10(578) ↗
8. Influence of binders on properties of sintered fly ash aggregate10.1016/j.cemconcomp.2005.06.005 ↗
9. Jaroslav · 1988
10. http://www.hvfacprojectindia.com/Summary_Report.pdf; 23.10.2009.
11. Reuse potential of low-calcium bottom ash as aggregate through pelletization10.1016/j.wasman.2010.03.027 ↗
12. ASTM C 618. Standard specification for fly ash and raw or calcined natural pozzolan for use as a mineral admixture in Portland cement concrete. American Society of Test. Mater, Philadelphia; 1998.
13. ASTM C 29. Standard test method for bulk density (“unit weight”) and voids in aggregate. American Society of Testing and Materials, Philadelphia; 2007.
14. BSI BS 812-111 91990. Testing aggregates part 111: methods for determination of ten per cent fines value (TFV). British Standards Institution.
15. ASTM C 127. Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate; 2007.
16. Comparison of ASTM saturation techniques for measuring permeable porosity of concrete10.1016/j.cemconres.2004.09.017 ↗
17. SAS Release 8.02. SAS Institute Inc., Cary, NC, USA.
18. Specifications for Structural Concrete ACI 301-05. American Concrete Institute, Farmington Hills; 2005.
19. ASTM C 125. Standard terminology relating to concrete and concrete aggregate. American Society of Testing and Materials, Philadelphia; 2006.
20. Mechanical characteristics of clay structural ceramics containing coal fly ash10.1007/s10999-007-9049-8 ↗
21. Ceramic strength and its relation to the kinetic parameters of sintering10.1023/A:1014031032542 ↗
22. Final stages of sintering of ceramic materials: effect of residual porosity and microstructure on mechanical characteristics of surface10.1016/S0272-8842(96)00041-7 ↗
23. William · 1994
24. Influence of sintering temperature on microstructural changes of ceramic Raschig ring10.1007/s11814-009-0085-y ↗
25. The effect of sintering temperature on porous silica composite strength10.1023/A:1024070114030 ↗
26. Newman · 1993
27. Properties of high Strength containing light, normal, and heavyweight aggregate