Physical and mechanical performance of cement-based renders with different contents of fly ash, expanded cork granules and expanded clay
Source abstract
Abstract
Abstract In recent decades, there has been a demand for new cladding solutions with higher thermal efficiency. Mortars with an improved thermal performance are one such solution. The biggest challenge in developing these mortars consists in achieving a lower thermal conductivity, while still maintaining an appropriate mechanical and water resistance performance with a low environmental impact. The aim of this study is to analyse the physical and mechanical performance of 20 cement-based coating mortars (renders) with different contents of a SCM – supplementary cementitious material (fly ash) used to replace cement, and of two insulating aggregates (expanded cork granules, expanded clay or a mix of both) replacing sand. The reduction of cement binder and sand aggregate contents led to lower thermal conductivity and a decrease of the mechanical properties. However, the balance between the physical and mechanical performance allows different applications, reaching thermal mortars with distinct EN 998 classes: (i) thermal conductivity T1 or T2; (ii) compressive strength CSI or CSII; (iii) water capillary absorption W0 or W1.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Magnesium Oxide Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Directive 2010/31/EU of the European parliament and of the council of 19 may 2010 on the energy performance of buildings, Off. J. Eur. Union 153 (2010) 13–35.
2. Directive 2012/27/EU of the European parliament and of the council of 25 October 2012 on energy efficiency, Off. J. Eur. Union 315 (2012) 1–55.
3. Anhydrite/aerogel composites for thermal insulation
4. The mechanical, transport and thermal properties of mortar and concrete containing waste cork10.1016/j.cemconcomp.2012.06.003 ↗
5. EN998-1 (2010) – Specification for mortar for masonry – Part 1: Rendering and plastering mortar, Comité Européen de Normalisation, Brussels, 2010.
6. Thermal conductivity of newspaper sandwiched aerated lightweight concrete panel10.1016/j.enbuild.2010.08.026 ↗
7. The variation of thermal conductivity of fibrous insulation materials under different levels of moisture content10.1016/j.conbuildmat.2013.02.058 ↗
8. Measurements of thermal properties of insulation materials by using transient plane source technique10.1016/j.applthermaleng.2006.04.006 ↗
9. An apparatus for the routine measurement of thermal conductivity of materials for building application based on a transient hot-wire method10.1016/j.applthermaleng.2007.02.008 ↗
10. “Silica-based aerogels as aggregates for cement-based thermal renders”10.1016/j.cemconcomp.2016.06.013 ↗
11. Aerogel-based renders with lightweight aggregates: correlation between molecular/pore structure and performance10.1016/j.conbuildmat.2016.07.103 ↗
12. Cement-cork mortars for thermal bridges correction. Comparison with cement-EPS mortars performance10.1016/j.conbuildmat.2013.08.006 ↗
13. Mechanical characterization of lightweight polymer mortar modified with cork granulates10.1016/j.compscitech.2004.03.006 ↗
14. Acoustic and mechanical properties of expanded clay granulates consolidated by epoxy resin10.1016/j.clay.2010.02.007 ↗
15. Modeling of adsorption of toxic chromium on natural and surface modified lightweight expanded clay aggregate (LECA)10.1016/j.apsusc.2013.09.175 ↗
16. The acoustical properties of consolidated expanded clay granulates10.1016/j.apacoust.2005.08.003 ↗
17. Mechanical characteristics of lightweight mortars on small-scale samples10.1520/JTE20140535 ↗
18. Contribution of fly ash to the properties of mortar and concrete
19. Characterization of high-volume fly-ash cement pastes for sustainable construction applications10.1016/j.conbuildmat.2017.09.089 ↗
20. The differences among the roles of ground fly ash in the paste, mortar and concrete10.1016/j.conbuildmat.2015.05.117 ↗
21. Influence of mineral admixtures on thermal conductivity and compressive strength of mortar10.1016/S0378-7788(02)00052-X ↗
22. Sustainable cement production – present and future10.1016/j.cemconres.2011.03.019 ↗
23. Trends and development in green cement and concrete technology10.1016/j.ijsbe.2013.05.001 ↗
24. Fly ash as an alternative energy efficient building material for cement
25. Thermal properties of high-volume fly ash mortars and concretes10.1177/1744259110376613 ↗
26. Increasing coal fly ash used in cement and concrete through chemical activation of reactivity of fly ash10.1080/00908310390195688 ↗
27. Impact of fly ash content and fly ash transportation distance on embodied greenhouse gas emissions and water consumption in concrete10.1007/s11367-009-0105-5 ↗
28. Thermo-mechanical properties of sand and high volume mineral admixtures10.1016/S0378-7788(02)00159-7 ↗
29. Effect of ultrafine fly ash on mechanical properties of high volume fly ash mortar10.1016/j.conbuildmat.2013.11.002 ↗
30. A study on the effect of nano silica on compressive strength of high volume fly ash mortars and concretes10.1016/j.matdes.2014.04.025 ↗
31. A brief on high-volume class F fly ash as cement replacement – a guide for civil engineer10.1016/j.ijsbe.2015.10.002 ↗
32. Effect of fly ash fineness on the performance of cement mortar
33. EN 1097-3 (1998) · 1998 · 1998
34. EN1015-11 (1999) · 1999 · 1999
35. ASTM 1876-01 (2009) · 2009
36. EN 12504–4 (2004) · 2004 · 2004
37. EN 1015–10 (1999) · 1999 · 1999
38. EN 1936 (2006) · 2006
39. In-service parameters from façade rendering mortars; Bulk density and open porosity determined from samples collected in situ10.1108/02630801011040833 ↗
40. ISOMET 2114 – Thermal properties analyser. User’s Guide, Version 120712.
41. EN 1015–18 (2000) · 2000
42. CNR -ICR. NORMAL 29/88 (1991). Measurement of material loss absorbed water by evaporation, Commissione NORMAL, Doc. n° 29/88, Rome, 1991. (in Italian).10.1007/BF00686344 ↗
43. Drying index for in-service physical performance assessment of renders10.1016/j.conbuildmat.2016.03.034 ↗