journal article·2018-12Open access

Structural behaviour and design of chord plastification in high strength steel CHS X-joints

Xiaoyi Lan, Tak-Ming Chan, Ben Young

Abstract

Abstract This paper aims to investigate the structural behaviour and static strength of high strength steel circular hollow section (CHS) X-joints under axial compression in the braces. Extensive numerical simulations on the CHS X-joints using S460, S700, S900 and S1100 steel were carried out. The failure mode of the CHS X-joints investigated is chord plastification. Effects of heat affected zones on the initial stiffness and static strength of the CHS X-joints are found to be relatively insignificant. Suitability of the mean strength equation adopted by the CIDECT design guide for the CHS X-joints was evaluated against results obtained from the numerical simulations in this study and experimental tests in the literature. In general, the CIDECT mean strength prediction is slightly unconservative for CHS X-joints in S460 steel and becomes increasingly unconservative with increasing steel grade. This is because the improved yield stress of high strength steel generally could not be fully utilised in the CHS X-joints mainly due to the adopted indentation limit i.e. 3% of chord diameter. The recommended ranges of chord diameter to wall thickness ratio (2γ) are 2γ ≤ 40 for steel grades ranging from S460 to S700 and 2γ ≤ 30 for steel grades greater than S700 and up to S1100 to allow for more effective use of high strength steel. The suggested range of brace to chord diameter ratio (β) is 0.2 ≤ β ≤ 1.0 for steel grades ranging from S460 to S1100, which is the same as the current CIDECT validity range of β ratio. A mean strength equation was proposed for the CHS X-joints with 2γ and β ratios which are within the suggested ranges. The statistical analysis shows that the proposed mean strength equation can produce reasonably accurate and consistent strength prediction. The proposed mean strength equation was converted to a design strength equation for the design of high strength steel CHS X-joints.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Load-Bearing Analysis · Structural Behavior of Reinforced Concrete · Fire effects on concrete materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Eurocode 3 (EC3), Design of Steel Structures-Part 1–8: Design of Joints. European Committee for Standardization, EN 1993-1-8, CEN, Brussels, 2005.
2. Packer · 2009
3. Wardenier · 2008
4. ISO. Static design procedure for welded hollow-section joints-Recommendations. ISO/FDIS 14346: 2012(E), Geneva.
5. International Institute of Welding (IIW) Subcommission XV-E, XV-1281-08: Static Design Procedure for Welded Hollow Section Joints-Recommendations, 3rd Ed., 2008.
6. American Petroleum Institute (API), Recommended practice for planning, designing and constructing fixed offshore platforms-working stress design, API Recommended Practice 2A WSD (RP 2A WSD), 22nd Ed., 2014 (Washington).
7. ANSI/AISC 360-10. Specification for structural steel buildings. American Institute of Steel Construction (AISC), Chicago, 2010.
8. D.K. Liu, J. Wardenier, Effect of the yield strength on the static strength of uniplanar K-Joints in RHS (Steel Grade S460, S355 and S235), IIW Doc. XV-E-04-293, 2004.
9. Y. Kurobane, New Development and Practices in Tubular Joint Design, IIW Doc. XV-448-81 and IIW Doc. XIII-1004-81, 1981.
10. C. Noordhoek, A. Verheul, R.J. Foeken, H.M. Bolt, P.J. Wicks, Static strength of high strength steel tubular joints, ECSC agreement number 7210-MC/602, 1996.
11. EN 1993-1-12, Eurocode 3: Design of Steel Structures-Part 1–12: Additional Rules for the Extension of EN 1993 up to Steel Grades S700, European Committee for Standardization, EN 1993-1-12, CEN, Brussels, 2007.
12. New IIW (2008) static design recommendations for hollow section joints
13. The capacity of grade C450 cold-formed rectangular hollow section T and X connections: an experimental investigation10.1016/j.jcsr.2017.02.032 ↗
14. FEA of T & X joints in Grade C450 steel
15. Finite element simulations of 450 grade cold-formed K and N joints
16. A design methodology for sidewall failure of RHS truss X-joints accounting for compressive chord pre-load10.1016/j.engstruct.2016.08.019 ↗
17. R. Puthli, O. Bucak, S. Herion, O. Fleischer, A. Fischl, O. Josat, Adaptation and extension of the valid design formulae for joints made of high-strength steels up to S690 for cold-formed and hot-rolled sections, CIDECT Report 5BT-7/10 (Draft Final Report), CIDECT, Germany, 2011.
18. Experimental and numerical study of cold-formed high-strength steel CHS X-joints10.1061/(ASCE)ST.1943-541X.0001806 ↗
19. Static strength of high strength steel CHS X-joints under axial compression10.1016/j.jcsr.2017.07.003 ↗
20. Abaqus/Standard. Version 6.13-1. USA: K. a. S. Hibbit, 2013.
21. Deformation limit for the ultimate strength of hollow section joints
22. R. Stroetmann, Thoralf Kastner, A. Halsig, P. Mayr, Mechanical properties and a new design approach for welded joints at high strength steels, Engineering Research and Practice for Steel Construction, Hong Kong 2018, pp. 79–90.
23. Effect of weld on the mechanical properties of high strength and ultra-high strength steel tubes in fabricated hybrid sections10.1016/j.engstruct.2016.03.046 ↗
24. Fatigue testing of butt-welded high strength square hollow sections strengthened with CFRP10.1016/j.tws.2017.09.004 ↗
25. Hardness and compressive capacity of longitudinally welded very high strength steel tubes10.1016/j.jcsr.2015.09.008 ↗
26. Laser and laser gas-metal-arc hybrid welding of 960 MPa direct-quenched structural steel in a butt joint configuration10.2351/1.4906386 ↗
27. Plastic strain characteristics of butt-welded ultra-high strength steel (UHSS)10.1016/j.tws.2016.09.024 ↗
28. Material properties and residual stresses of cold-formed high strength steel hollow sections10.1016/j.jcsr.2015.02.006 ↗
29. Eurocode 3 (EC3), Design of Steel Structures-Part 1–1: General Rules and Rules for Buildings. European Committee for Standardization, EN 1993-1-1, CEN, Brussels, 2005.
30. Stress-strain curves for hot-rolled steels10.1016/j.jcsr.2017.01.024 ↗
31. Wardenier · 1982
32. International Institute of Welding (IIW) Subcommission XV-E, XV-701-89: Design recommendations for hollow section joints-predominantly statically loaded, 2nd ed., 1989 (Helsinki).
33. Evaluation of new CHS strength formulae to design strengths
34. New API RP2A tubular joint strength design provisions10.1115/1.2748811 ↗
35. Wardenier · 2011
36. Effect of chord load on ultimate strength of CHS X-joints
37. Analysis and calculation of axial stiffness of tubular X-joints under compression on braces10.1007/s12204-009-0410-y ↗
38. Design of cold-formed high strength steel tubular beams10.1016/j.engstruct.2017.08.002 ↗
39. Strength of internally ring-stiffened tubular DT-joints subjected to brace axial loading10.1016/j.jcsr.2016.06.012 ↗
40. Joint strength reduction factor of internally ring-stiffened tubular joints at elevated temperatures10.1177/1369433216648049 ↗
41. Axial compression capacity of steel CHS X-joints strengthened with external stiffeners10.1016/j.jcsr.2017.11.009 ↗
42. Static capacity of tubular X-joints reinforced with collar plate subjected to brace compression10.1016/j.tws.2017.06.012 ↗
43. Static strength of doubler plate reinforced CHS X-joints loaded by in-plane bending10.1016/j.jcsr.2004.05.004 ↗
44. Experimental investigation of concrete-filled high-strength steel tubular X joints10.1061/(ASCE)ST.1943-541X.0002176 ↗
45. Design of concrete-filled high strength steel tubular joints subjected to compression10.1016/j.jcsr.2018.07.030 ↗