Effect of pitting defects on the buckling strength of thick-wall cylinder under axial compression
Source abstract
Abstract
Abstract This paper is aimed at assessing the effects of uniformly and randomly distributed pitting defects on the collapse pressure (FCO) of thick-wall cylinder under axial compression, which is exposed to the marine splash zone. The buckling performance of locally corroded cylinder was experimental and numerical studied. The experimental program involved seamless stainless steel tubes (316L) with different size of pitting defects, which were simulated by cylindrical hole. The pitting defects were introduced into the outside surface of cylinder by milling and drilling, and then the buckling strength of such structure was obtained experimentally. The profile of cylinder was examined in details using RA7320 Portable Arm Coordinate Measuring Machine (PACMM), and the measured data was analyzed carefully. A novel shell model was also established by a user defined Python program, where both uniformly and randomly distributed pits can be considered and the computational efficiency was highly improved. After calibrated with the experiment results, the model was used to carry out a systematic parametric study. It indicated that the radial imperfection and out-of-straightness as well as pitting defects (pitting size, perforated or un-perforated and distribution pattern) are key parameters governing the collapse pressure of such cylinder, and the maximum cross sectional area loss or volume loss are good parameter to correlate the collapse pressure and pitting damage. For engineering practice, the uniformly distributed pits model is better due to the convenience and conservative point of view, and the computational cost is also lower. However, the randomly distributed pitting model is more realistic, and some special collapse mode can only be observed when the random nature was taken into account.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Integrity and Reliability Analysis · Concrete Corrosion and Durability · Corrosion Behavior and Inhibition
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Corrosion behavior of X65 pipeline steel: comparison of wet-dry cycle and full immersion10.1016/j.corsci.2018.01.007 ↗
2. Experimental investigation of short steel columns with localized corrosion10.1016/j.tws.2014.11.009 ↗
3. Collapse of HSLA steel pipes under corrosion exposure and uniaxial inelastic cycling10.1016/j.jcsr.2018.02.003 ↗
4. Manual for determining the remaining strength of corroded pipelines: a supplement to ASME B31 code for pressure piping
5. D.N. Veritas, Recommended practice DNV-RP-F101 corroded pipelines, 11; 2015. Hovik, Norway.
6. Ultimate strength analysis of aged steel-plated structures exposed to marine corrosion damage: a review10.1016/j.corsci.2014.04.043 ↗
7. On the effect of axial length parameters of ovality on the collapse pressure of pipelines10.1016/j.tws.2017.02.032 ↗
8. Development of erosion equation and numerical simulation methods with the consideration of applied stress10.1016/j.triboint.2019.05.019 ↗
9. Research of collapse pressure of 90° elbow with internal erosion-corrosion damage
10. Research of plastic collapse capacity of 2D ring with internal random pitting corrosion defects
11. Chloride-induced corrosion of steel reinforcement – mechanical performance and pit depth analysis10.1016/j.conbuildmat.2012.07.087 ↗
12. Variation of steel loss and its effect on the ultimate flexural capacity of RC beams corroded and repaired under load10.1016/j.conbuildmat.2009.11.012 ↗
13. Three-dimensional corrosion pit measurement and statistical mechanical degradation analysis of deformed steel bars subjected to accelerated corrosion10.1016/j.conbuildmat.2014.08.001 ↗
14. Effect of simulated pitting corrosion on the tensile properties of steel10.1016/j.conbuildmat.2016.11.037 ↗
15. Predicting the residual strength and deformability of corroded steel plate based on the corrosion morphology10.1016/j.conbuildmat.2017.07.035 ↗
16. Computation of plastic collapse capacity of 2D ring with random pitting corrosion defect10.1016/j.tws.2017.07.025 ↗
17. Effect of 3D random pitting defects on the collapse pressure of pipe — part I: experiment10.1016/j.tws.2018.04.015 ↗
18. Effect of 3D random pitting defects on the collapse pressure of pipe — part II: numerical analysis10.1016/j.tws.2018.04.014 ↗
19. On the general theory of elastic stability
20. Buckling behavior of axially compressed cylindrical shells: comparison of theoretical and experimental data10.1016/j.tws.2015.10.027 ↗
21. Numerical and experimental investigation on ultimate strength of cracked cylindrical shells subjected to combined loading
22. Teng · 2004
23. Robust design criterion for axially loaded cylindrical shells – simulation and validation10.1016/j.tws.2016.12.017 ↗
24. The effect ofaxisymmetric imperfections on the buckling of cylindrical shells under axial compression
25. Arbocz · 1982
26. Peterson · 1968
27. Stimulating the realistic worst case buckling scenario of axially compressed unstiffened cylindrical composite shells10.1016/j.compstruct.2016.10.108 ↗
28. An analytical and numerical study on the buckling of cracked cylindrical shells10.1016/j.tws.2017.06.023 ↗
29. Numerical and experimental investigations of the response of aluminum cylinders with a cutout subject to axial compression10.1016/j.tws.2005.11.003 ↗
30. Numerical and experimental investigations on buckling of steel cylindrical shells with elliptical cutout subject to axial compression10.1016/j.tws.2008.02.005 ↗
31. Buckling of steel cylindrical shells with an elliptical cutout10.1007/BF03215830 ↗
32. Structural behavior of shells with different cutouts under compression: an experimental study10.1016/j.jcsr.2014.10.020 ↗
33. Empirical equations to estimate non-linear collapse of medium-length cylindrical shells with circular cutouts10.1016/j.tws.2017.08.008 ↗
34. Recovery of capacity lost due to openings in cylindrical shells under compression10.1016/j.jcsr.2017.06.006 ↗
35. Numerical methods for the design of cylindrical steel shells with unreinforced or reinforced cutouts10.1016/j.tws.2015.07.024 ↗
36. Effect of multiple holes on dynamic buckling of stubby shells: an experimental and numerical investigation10.1016/j.ijimpeng.2016.05.014 ↗
37. A numerical study of damage caused by combined pitting corrosion and axial stress in steel pipes10.1016/j.corsci.2013.07.002 ↗
38. Sun · Corros. Sci. · 2018
39. C. Hühne, R. Rolfes, J. Teßmer, A new approach for robust design of composite cylindrical shells under axial compression. In: Proceedings of the European conference on spacecraft structures.
40. Worst multiple perturbation load approach of stiffened shells with and without cutouts for improved knockdown factors10.1016/j.tws.2014.05.004 ↗
41. Robust knockdown factors for the design of axially loaded cylindrical and conical composite shells – development and validation10.1016/j.compstruct.2017.02.031 ↗
42. Hybrid framework for reliability-based design optimization of imperfect stiffened shells10.2514/1.J053816 ↗
43. Influence of imperfection distributions for cylindrical stiffened shells with weld lands10.1016/j.tws.2015.03.017 ↗
44. Experimental and numerical analyses of the ultimate compressive strength of perforated offshore tubular members10.1016/j.marstruc.2017.10.010 ↗
45. Buckling of cylinders with cutouts under axial compression10.1007/BF02330057 ↗
46. Effect of openings on the buckling of cylindrical shells subjected to axial compression10.1016/S0263-8231(98)00003-2 ↗
47. Influence of a cutout on circular steel hollow sections under cyclic loading10.1016/j.jcsr.2014.04.015 ↗
48. European Committee for Standardization, Eurocode 3: Design of Steel Structures, Part 1–6: Strength and Stability of Shell Structures, 2006.
49. Dong · 2005 · 12
50. GB/T 228.1-2010. Metallic materials—Tensile testing—Part 1: Method of test at room temperature (ISO 6892-1:2009, MOD). 2011.
51. ABAQUS, User's Manual: Version 6.12, Simulia, United States, 2013.
52. Environmental embrittlement of automobile spring steels caused by wet-dry cyclic corrosion in sodium chloride solution10.1016/j.corsci.2004.10.008 ↗
53. Novel images of the evolution of stress corrosion cracks from corrosion pits10.1016/j.corsci.2011.05.050 ↗
54. Stochastic modeling of pitting corrosion: a new model for initiation and growth of multiple corrosion pits10.1016/j.corsci.2006.05.049 ↗