Partially fly ash incorporated recycled coarse aggregate based concrete: Microstructure perspectives and critical analysis
Source abstract
Abstract
Abstract This paper presents experimental investigation of the microstructure of partial cement substituted fly ash incorporated recycled aggregate concrete (FARAC). Testing techniques such as thermo-gravimetric analysis, scanning electron microscopy, nano-indentation and X-ray tomography were adopted for this study. Effects of parameters like (i) percentage of fly ash (20% and 30% as cement replacement by weight), (ii) particle packing mix design and conventional method, (iii) curing ages (7, 28 and 90 days), and (iv) coarse aggregate types (100% natural or recycled) are examined. Degree of hydration of FARAC, though higher than natural aggregate concrete, did not translate directly into compressive strength due to formation of more loosely connected low density C-S-H confirmed by SEM images. It is observed that micro-cracks pass mostly through the old and fresh bulk paste rather than the old ITZ in 90 days cured concrete. Thickness of the old ITZ as well as heterogeneities of the new ITZ reduced in FARAC. Upto 30% fly ash can compensate higher porosity of RAC through formation of spherical smaller-size pores.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Recycled Aggregate Concrete Performance · Concrete and Cement Materials Research · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Hydration mechanisms of ternary Portland cements containing limestone powder and fly ash10.1016/j.cemconres.2010.11.014 ↗
2. Properties of concrete containing construction and demolition wastes and fly ash10.1061/(ASCE)MT.1943-5533.0000763 ↗
3. Effect of the water to binder ratio and ground fly ash on properties of recycled aggregate concrete10.1061/(ASCE)MT.1943-5533.0000360 ↗
4. Recycled aggregate concrete incorporating fly ash: comparative study on particle packing and conventional method10.1016/j.conbuildmat.2017.08.132 ↗
5. Long-term mechanical and durability properties of recycled aggregate concrete prepared with the incorporation of fly ash10.1016/j.cemconcomp.2012.12.011 ↗
6. Enhancing mechanical and durability properties of recycled aggregate concrete10.1016/j.conbuildmat.2017.09.137 ↗
7. Shear performance of reinforced concrete beams incorporating recycled concrete aggregate and high-volume fly ash10.1016/j.jclepro.2015.12.017 ↗
8. Flexural performance and tension-stiffening evaluation of reinforced concrete beam incorporating recycled aggregate and fly ash10.1016/j.conbuildmat.2018.04.072 ↗
9. Performance of fly ash incorporated recycled aggregates concrete column under axial compression: experimental and numerical study10.1016/j.engstruct.2019.05.099 ↗
10. Interfacial transition zones in recycled aggregate concrete with different mixing approaches10.1016/j.conbuildmat.2012.06.022 ↗
11. Micromechanical multiscale modeling of ITZ-driven failure of recycled concrete: effects of composition and maturity on the material strength10.3390/app8060976 ↗
12. Multi-aggregate approach for modelling interfacial transition zone in concrete
13. Physio-chemical reactions in recycle aggregate concrete10.1016/j.jhazmat.2008.07.031 ↗
14. Microstructure analysis of hardened recycled aggregate concrete10.1680/macr.2006.58.10.683 ↗
15. Effect and mechanism of surface-coating pozzalanics materials around aggregate on properties and ITZ microstructure of recycled aggregate concrete10.1016/j.conbuildmat.2009.10.038 ↗
16. Properties of interfacial transition zones in recycled aggregate concrete tested by nanoindentation10.1016/j.cemconcomp.2013.01.006 ↗
17. Microstructural analysis of recycled concrete using X-ray microtomography10.1016/j.cemconres.2015.11.010 ↗
18. Considerations in image analysis as applied to investigations of the ITZ in concrete10.1016/S0958-9465(00)00085-8 ↗
19. IS (Indian Standard). (1963). Indian standards methods of tests for aggregates for concrete part I,III and IV, IS 2386-63, New Delhi,India. (Reaffirmed 2002).
20. IS (Indian Standard), Methods of physical tests of hydraulic cement, IS 4031-88, New Delhi, India, 1988. (Reaffirmed 2000).
21. IS (Indian Standard) (2003) Pulverised fuel ash specification, IS:3812-2003, Bureau of Indian Standards, New Delhi, India.
22. IS (Indian Standard) (1985), Methods of chemical analysis of hydraulic cement. IS 4032-85, Bureau of Indian Standards, New Delhi, India. (Reaffirmed 2005).
23. ASTM. (2015). Standard – Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete, ASTM C 618, United States.
24. IS (Indian Standard) (1959). “Methods of tests for strength of concrete”, IS: 516-1959, Bureau of Indian Standards, New Delhi, India. (Reaffirmed 2004).
25. DTA and heat-flux DSC measurements of alloy melting and freezing
26. Pozzolanic and cementitious reactions of fly ash in blended cement pastes10.1016/0008-8846(88)90014-2 ↗
27. The degree of hydration assessment of blended cement pastes by differential thermal and thermogravimetric analysis. Morphological evolution of the solid phases10.1016/j.tca.2014.08.008 ↗
28. Quantification of hydrated cement products of blended cements in low and medium strength concrete using TG and DTA technique10.1016/S0040-6031(03)00286-7 ↗
29. Backscattered electron imaging of cementitious microstructures: understanding and quantification10.1016/j.cemconcomp.2004.02.029 ↗
30. Brand · 2015
31. Pore segmentation of cement-based materials from backscattered electron images10.1016/j.cemconres.2005.10.006 ↗
32. Digital image smoothing and the sigma filter10.1016/0734-189X(83)90047-6 ↗
33. Simple and fast porosity analysis of concrete using X-ray computed tomography10.1617/s11527-014-0519-9 ↗
34. Estimation of calcium hydroxide in OPC, OPC/PFA and OPC/PFA/polymer modified systems10.1016/0040-6031(86)85122-X ↗
35. Investigation of blended cement hydration by isothermal calorimetry and thermal analysis10.1016/j.cemconres.2004.10.027 ↗
36. The occurrence of duplex films on flyash surfaces10.1016/0008-8846(80)90086-1 ↗
37. Hydration in high-volume fly ash concrete binders
38. Degree of hydration and gel/space ratio of high-volume fly ash/cement systems10.1016/S0008-8846(00)00213-1 ↗
39. Carbonation rates of concretes containing high volume of pozzolanic materials10.1016/j.cemconres.2007.08.014 ↗
40. Effect of microstructure of ITZ on compressive strength of concrete prepared with recycled aggregates10.1016/j.conbuildmat.2004.03.005 ↗
41. The characterization of hardened alkali-activated blast-furnace slag pastes and the nature of the calcium silicate hydrate (CSH) phase10.1016/0008-8846(94)90002-7 ↗
42. The effect of two types of CSH on the elasticity of cement-based materials: results from nanoindentation and micromechanical modelling10.1016/S0008-8846(03)00230-8 ↗
43. Nano-mechanical behaviour of a green ultra-high performance concrete10.1016/j.conbuildmat.2014.04.029 ↗
44. The nano-mechanical signature of ultra high performance concrete by statistical nanoindentation techniques10.1016/j.cemconres.2008.09.002 ↗
45. Nanoindentation characteristics of alkali-activated aluminosilicate materials10.1016/j.cemconcomp.2010.10.005 ↗
46. P.K. Mehta, P. Monteiro. Concrete microstructure, properties and materials, 2006.