journal article·2012-11

Effect of curing regime and temperature on the compressive strength of cement-slag mortars

Fathollah Sajedi

Publisher page

Abstract

Abstract In this experimental work 24 mixes were prepared. Each mix was made using binder contents 380 and 500 kg/m3. All the made mixes are classified into three groups as OPC, OPC-slag and slag mortars. Each group includes eight mixes and the specimens were cured in different curing regimes after casting and demoulding, i.e. under room temperature (ac), in water without heating (wc), room temperature after heating 60 °C for duration 20 h (WH/ac) and in water after heating like as mentioned (WH/wc). The results showed that the highest strength is related to the OPC-slag mortars as 80 MPa for OSM380-wc. For all groups of mortars, there could rarely be strength loss at later ages. The results proved that WH/ac is the optimum curing regime for all groups of mortars in duration of 3–7 days, whereas the optimum curing regime is not the same in duration of 28–90 days. It was proved that higher strength could be achieved for OPC and OPC-slag mortars using lower binder content provided the specimens are cured in water without heating. This reality is reversed for slag mortars; namely for slag mortars the highest strengths could be only achieved using more slag content and water curing without heating. For SM500-wc the strengths obtained at 28 and 90 days were as 18 and 26 MPa, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Concrete Properties and Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Strength behaviour of mortar using slag with cement in sea water environment
2. Ekaputri JJ, Ishida T, Maekawa K. Autogeneous shrinkage of mortars made with different types of sag cement. JCI annual convention, 1st ed. Japan: Saitama; 2010.
3. Replacement of cement by limestone filler or ground granulated blast furnace slag: the effect of chloride penetration in cement mortars
4. Interrelation between fine grinding and mechanical activation10.1016/0301-7516(95)00028-3 ↗
5. Influence of curing temperature on cement hydration and mechanical strength development of fly ash mortars10.1016/S0008-8846(97)00098-7 ↗
6. Effect of curing temperature on the thermal expansion and phase composition of hydrated limestone-slag cement
7. Sajedi F. Influence of activation methods on strength of ordinary Portland cement-slag mortars, University of Malaya, Kuala Lumpur (Malaysia); 2011.10.1016/j.conbuildmat.2010.06.060 ↗
8. ASTM C109-99. Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens).
9. Investigation of hydraulic activity of ground granulated blast furnace slag in concrete10.1016/S0008-8846(03)00062-0 ↗
10. Effect of temperature and aging on the mechanical properties of concrete, Part II. Prediction model10.1016/S0008-8846(02)00745-7 ↗
11. ASTM C989. Standard specification for slag cement for use in concrete and mortars.
12. BSI. Testing aggregates: method for determination of particle size distribution. Sieve tests, BS 812–103.1:1985. UK: British Standard Institute; 1985.
13. Neville · 2008
14. Neville · 2008
15. ASTM C494. Standard specification for chemical admixtures for concrete.
16. ASTM C230/C230M-08. Standard specifications for flow table for use in tests of hydraulic cement.
17. BSI. Method for determination of compressive strength of concrete cubes BS1881-Part 116. UK: British Standard Institute; 1881.
18. Optimum level of replacement slag in OPC-slag mortars
19. Thermal activation of ordinary Portland cement-slag mortars10.1016/j.matdes.2010.04.011 ↗
20. The effect of heat treatment on the compressive strength of cement-slag mortars10.1016/j.matdes.2011.04.038 ↗
21. Comparison of different methods for activation of ordinary Portland cement-slag mortars10.1016/j.conbuildmat.2010.06.060 ↗
22. Effects of curing regimes and cement fineness on the compressive strength of ordinary Portland cement mortars10.1016/j.conbuildmat.2010.11.043 ↗