Investigation of moisture condition and Autoclam sensitivity on air permeability measurements for both normal concrete and high performance concrete
Source abstract
Abstract
While on site measurement of air permeability provides a useful approach for assessing the likely long term durability of concrete structures, no existing test method is capable of effectively determining the relative permeability of high performance concrete (HPC). Lack of instrument sensitivity and the influence of concrete moisture are proposed as two key reasons for this phenomenon. With limited systematic research carried out in this area to date, the aim if this study was to investigate the influence of instrument sensitivity and moisture condition on air permeability measurements for both normal concrete and HPC. To achieve a range of moisture conditions, samples were dried initially for between one and 5 weeks and then sealed in polythene sheeting and stored in an oven at 50 °C to internally distribute moisture evenly. Moisture distribution was determined throughout using relative humidity probe and electrical resistance measurements. Concrete air permeability was subsequently measured using standardised air permeability (Autoclam) and water penetration (BS EN: 12390-8) tests to assess differences between the HPCs tested in this study. It was found that for both normal and high performance concrete, the influence of moisture on Autoclam air permeability results could be eliminated by pre-drying (50 ± 1 °C, RH 35%) specimens for 3 weeks. While drying for 5 weeks alone was found not to result in uniform internal moisture distributions, this state was achieved by exposing specimens to a further 3 weeks of sealed pre-conditioning at 50 ± 1 °C. While the Autoclam test was not able to accurately identify relative HPC quality due to low sensitivity at associated performance levels, an effective preconditioning procedure to obtain reliable air permeability of HPC concretes was identified.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Concrete and Cement Materials Research · Concrete Properties and Behavior · Concrete Corrosion and Durability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Aïtcin · 1998
2. Neville · 1996
3. Mehta · 2006
4. Assessment of the durability of concrete from its permeation properties: a review10.1016/S0950-0618(00)00058-1 ↗
5. Basheer PAM. Permeation analysis. In: Ramachandran VS, Beaudoin JJ, editors. Handbook of analytical techniques in concrete science and technology: principles, techniques and applications; 2001. p. 658–27.10.1016/B978-081551437-4.50019-9 ↗
6. Bungey · 2006
7. Gas permeability of concrete in relation to its degree of saturation10.1007/BF02480405 ↗
8. Mechanical and durability properties of high performance concretes containing supplementary cementitious materials10.1016/j.conbuildmat.2009.08.045 ↗
9. Effect of moisture and concrete composition on the Torrent permeability measurement10.1617/14321 ↗
10. Jacobs F, Hunkeler F. Non destructive testing of the concrete cover–evaluation of permeability test data. In: International RILEM workshop, performance based evaluation and indicators for concrete durability. Madrid 2006. pp. 1–8.
11. A two-chamber vacuum cell for measuring the coefficient of permeability to air of the concrete cover on site10.1007/BF02472595 ↗
12. Basheer PAM. ‘CLAM’ permeability tests for assessing the durability of concrete. PhD thesis, Belfast, Queen’s University Belfast; 1991. p. 438.
13. Russell DP. Influence of environmental conditions and material properties on carbonation in concrete. PhD thesis, Belfast, Queen’s University Belfast; 1999. p. 335.
14. BS-EN:197–1. Cement. Composition, specifications and conformity criteria for common cements. BSI; 2000. p. 52.
15. BS-EN:450. Fly ash for concrete-part 1: definition, specifications and conformity criteria. BSI; 2005. p. 36.
16. BS-EN:13263-1. Silica fume for concrete. Definitions, requirements and conformity criteria. BSI; 2009. p. 28.
17. BS-EN:12350. Testing fresh concrete. Part 7: Air content. Pressure method, BSI; 2009. p. 24.
18. BS-EN:12350. Testing fresh concrete. Part 2: Slump test, BSI; 2009. P. 9.
19. BS-EN:12390. Testing hardened concrete. Part 3: Compressive strength of test specimens, BSI; 2009. p. 19.
20. BS1881-125. Methods for mixing and sampling fresh concrete in the laboratory. BSI; 1986. p. 10.
21. Nolan EA. Influence of near surface moisture gradients in concrete on ‘Autoclam’ permeation measurements. PhD thesis, Belfast, Queen’s University Belfast; 1996. p. 342.
22. BS-EN12390. Testing hardened concrete. Part 8: Depth of penetration of water under pressure. BSI; 2000. p. 10.
23. Near-surface moisture gradients and in situ permeation tests10.1016/S0950-0618(00)00059-3 ↗
24. Absorption of water and chloride into concrete10.1680/macr.1992.44.158.31 ↗
25. The autoclam – a new test for permeability, concrete
26. Characterization and identification of equilibrium and transfer moisture properties for ordinary and high-performance cementitious materials10.1016/S0008-8846(99)00102-7 ↗
27. Self-desiccation and its importance in concrete technology10.1007/BF02486354 ↗
28. Water vapour sorption experiments on hardened cementitious materials Part I: essential tool for analysis of hygral behaviour and its relation to pore structure10.1016/j.cemconres.2006.11.019 ↗
29. Induced anisotropic permeability due to drying of concrete10.1016/S0008-8846(02)01039-6 ↗
30. Near–surface sensors for condition monitoring of cover-zone concrete10.1016/S0950-0618(00)00060-X ↗
31. Moisture conditioning and transport properties of concrete test specimens10.1007/BF02473450 ↗
32. Procedure to interpret electrical conductivity measurements in cover concrete during rewetting10.1061/(ASCE)0899-1561(2005)17:5(586) ↗
33. Arbaoui T. Finite Element Calibration of the CLAM. MSc thesis, Belfast, Queen’s University Belfast; 1988. p. 103
34. ‘CLAM’ tests for measuring in-situ permeation properties of concrete10.1080/10589759508952835 ↗
35. Preparing specimens for microscopy
36. Near surface characteristics of concrete intrinsic permeability10.1680/macr.1989.41.147.87 ↗
37. Influence of the interfacial transition zone and microcracking on the diffusivity, permeability and sorptivity of cement-based materials after drying10.1680/macr.2008.61.8.571 ↗
38. Rehydration and microstructure of cement paste after heating at temperatures up to 300°C10.1016/S0008-8846(03)00005-X ↗
39. Permeability and pore structure evolution of silico calcareous and hematite high strength concretes submitted to high temperatures
40. Taylor · 1997