journal article·2016-06

Laboratory evaluation on the characteristics and pollutant emissions of nanoclay and chemical warm mix asphalt modified binders

Mohd Ezree Abdullah, Mohd Rosli Hainin, Nur Izzi Md. Yusoff, Kemas Ahmad Zamhari, Norhidayah Hassan

Publisher page

Abstract

Abstract This study was conducted to investigate the performance characteristics of nanoclay- and chemical warm-mix asphalt (WMA) additive-modified asphalt binders in terms of their chemical, morphology, rheological and surface energy properties in comparison to conventional asphalt binder. Both the nanoclay modified asphalt binder (NCMB B) and the chemical WMA additive modified asphalt binder (CWAA) were artificially aged under short-term and long-term aging conditions prior to evaluation. The chemical and morphological properties were measured with Fourier Transform Infrared (FTIR) spectroscopy and Field-Emission Scanning Electron Microscopy (FE-SEM) respectively. Rheological evaluations were conducted to determine binder’s behavior under short-term aging in terms of frequency sweep, temperature sweep, and creep recovery tests by utilizing the dynamic shear rheometer (DSR) machine. Emission test was also conducted on the unmodified and modified WMA mixtures to estimate the gaseous pollutants emitted during their manufacture. FTIR spectroscopy results showed that the addition of WMA modifiers into asphalt binder could delay and weaken the oxidation reaction of the binder which in turn improved the aging process. However, the physical structure did not seem to show any changes after undergoing long term aging. The use of NCMB B 4% (by weight of asphalt binder) seemed to produce better resistance towards rutting when compared to CWAA 1%, 2% and 3% for unaged, and short- and long-term aging test conditions. The modified binders exhibit significantly higher surface energy and hence produced good adhesion between aggregates, which imply increased resistance toward moisture-induced damage. This study also revealed that the manufacture of WMA mixtures reduced up to 50% of the pollutants emitted during mixing in laboratory.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Pavement engineering materials: review on the use of warm-mix asphalt10.1016/j.conbuildmat.2012.06.038 ↗
2. Warm mix asphalt: an overview10.1016/j.jclepro.2011.11.053 ↗
3. A review on the exploration of nanomaterials application in pavement engineering
4. Hybrid input-output life cycle assessment of warm mix asphalt mixtures10.1016/j.jclepro.2014.11.035 ↗
5. Temperature rheological properties of warm asphalt binders10.1061/(ASCE)0899-1561(2009)21:7(316) ↗
6. Reducing the environmental impact of concrete and asphalt: a scenario approach10.1016/j.jclepro.2013.10.012 ↗
7. Al-Rawashdeh · 2008
8. Laboratory evaluation of warm mix asphalt
9. Goh · 2011
10. Sampath · 2010
11. The research on the use of warm mix asphalt for asphalt Pavement structures
12. Warm-mix asphalt: European practice
13. Performance of warm mix asphalt containing Sasobit®: State-of-the-art10.1016/j.conbuildmat.2012.08.015 ↗
14. Effect of temperature reduction, foaming water content, and aggregate moisture content on performance of foamed warm mix asphalt10.1016/j.conbuildmat.2013.07.081 ↗
15. Comparative sustainability assessment of warm-mix asphalts: a thermodynamic based hybrid life cycle analysis10.1016/j.resconrec.2011.07.005 ↗
16. Evaluation of Sasobit® for use in warm-mix asphalt
17. Evaluation of Aspha-Min® Zeolite for use in warm-mix asphalt
18. Evaluation of Evotherm® for use in warm-mix asphalt
19. A synthesis of warm-mix asphalt
20. Zaumanis · 2010
21. Laboratory evaluation of moisture susceptibility of hot-mix asphalt containing cementitious fillers10.1061/(ASCE)MT.1943-5533.0000064 ↗
22. Influence of warm-mix additives and reduced aging on the rheology of asphalt binders with different natural wax contents10.1061/(ASCE)MT.1943-5533.0000315 ↗
23. Performance characteristics of warm mix asphalt mixtures using with nanoclay and chemical warm mix asphalt modified binders
24. Asphalt Institute. 203, SP-1 Superpave Performance Graded Asphalt Binder Specification and Testing, Lexington.
25. American Association of State and Highway Transportation Officials (AASHTHO) · 2011
26. Analysis of moisture damage susceptibility of warm mix asphalt (WMA) mixtures based on Dynamic Mechanical Analyzer (DMA) testing and a fracture mechanics model10.1016/j.conbuildmat.2012.04.035 ↗
27. Nanomanipulator-assisted fabrication and characterization of carbon nanotubes inside scanning electron microscope10.1016/j.micron.2005.03.005 ↗
28. Microscopy Book Series
29. Low-voltage high-resolution scanning electron microscope imaging of the uncoated and Cr-coated zeolite Beta10.1016/j.micromeso.2005.12.019 ↗
30. Strategies and results of field emission scanning electron microscopy (FE-SEM) in the study of parasitic protozoa10.1016/j.micron.2006.11.003 ↗
31. Griffiths · 2007
32. Effects of thermal oxidative ageing on dynamic viscosity, TG/DTG, DTA and FTIR of SBS- and SBS/sulfur-modified asphalts10.1016/j.conbuildmat.2010.06.048 ↗
33. Comparison by Fourier Transforms Infrared (FTIR) spectroscopy of different ageing techniques: application to road bitumens10.1016/S0016-2361(00)00121-6 ↗
34. Rheology of warm mix asphalt binders with aged binders10.1016/j.conbuildmat.2010.06.040 ↗
35. De Groot · 2001
36. Gandhi · 2008
37. Rheological properties and chemical analysis of nanoclay and carbon microfiber modified asphalt with Fourier transform infrared spectroscopy10.1016/j.conbuildmat.2012.08.004 ↗
38. Wasiuddin · 2007
39. Evaluate the mechanism of the effect of hydrated lime on moisture damage of warm mix asphalt10.1016/j.conbuildmat.2013.05.079 ↗
40. Morphology development and compatibilization effect in nanoclay filled rubber blends10.1016/j.polymer.2010.08.002 ↗