journal article·2018-08

Investigating the effects of solarcure curing method on the compressive strength, microstructure and polymeric reaction of fly ash based geopolymer

Muhammad Zahid, Nasir Shafiq, Asif Jalal

Publisher page

Abstract

Abstract This paper presents the effects of the specially designed solarcure method on the properties of geopolymer binders. The solarcure method is composed of the box-shaped chamber that works on the principles of trapping solar radiations to regulate the adequate amount of heat and temperature inside the box. Two sets of geopolymer binder mix containing low-calcium fly ash (LCFA) and high-calcium fly ash (HCFA) as a base material was developed. One part of sodium hydroxide (5 M and 10 M) solution mixed with two parts of sodium silicate was used as an alkaline activator. Mortar cubes of 50 mm size were cast and cured in three different regimes; continuous oven (CO) curing, intermittent oven (IO) curing and solarcure (SC) curing were used for the compressive strength test. For constant curing; temperature was maintained at 60 °C 24-h, whereas in intermittent conditions (IO and SC), samples were cured in three cycles; each cycle was composed of 8 h curing then 16 h cooling. For IO curing, the oven temperature was maintained at 60 °C, however for SC curing; the solar-box chamber has achieved maximum inside temperature up to 90 °C for each curing cycle. Specially designed SC technique caused up-to 56% increase in compressive strength as compared to the compressive strength of CO cured samples. SC curing also improved the microstructure properties and geopolymer reaction product.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Magnesium Oxide Properties and Applications · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. The effect of temperature and duration of curing on the strength of fly ash based geopolymer mortar10.1016/j.proeng.2014.12.199 ↗
2. Very high strength (120 MPa) class F fly ash geopolymer mortar activated at different NaOH amount, heat curing temperature and heat curing duration10.1016/j.conbuildmat.2015.08.089 ↗
3. Geopolymeric materials prepared using Class F fly ash and elevated temperature curing10.1016/j.cemconres.2004.06.031 ↗
4. Resistance of geopolymer materials to acid attack10.1016/j.cemconres.2004.06.005 ↗
5. Preparation and properties of alkali activated metakaolin-based geopolymer
6. High-strength geopolymer using fine high-calcium fly ash10.1061/(ASCE)MT.1943-5533.0000161 ↗
7. Workability and strength of coarse high calcium fly ash geopolymer10.1016/j.cemconcomp.2006.11.002 ↗
8. Influence of fly ash fineness on strength, drying shrinkage and sulfate resistance of blended cement mortar10.1016/j.cemconres.2003.11.021 ↗
9. GEOPOLYMERS Inorganic polymerie new materials10.1007/BF01912193 ↗
10. The effect of alkali and Si/Al ratio on the development of mechanical properties of metakaolin-based geopolymers10.1016/j.colsurfa.2006.05.044 ↗
11. Effectiveness of low-concentration acid and solar drying as pre-treatment features for producing pozzolanic sugarcane bagasse ash10.1016/j.jclepro.2015.09.066 ↗
12. Assessment of Greener Cement by employing thermally treated sugarcane straw ashes10.1016/j.conbuildmat.2017.03.022 ↗
13. Metakaolin-, fly ash- and calcium hydroxide-based geopolymers : effects of calcium on performance10.1680/jadcr.14.00081 ↗
14. D. Hardjito, Studies of fly ash-based geopolymer concrete, Ph. D. Curtin Univ. Technol. Dept. Civ. Eng., 2005, http://espace.library.curtin.edu.au/cgi-bin/espace.pdf?file=/2008/09/16/file_1/18580.
15. Development and properties of low-calcium fly ash-based geopolymer concrete
16. Performance evaluation and microstructure characterization of metakaolin-based geopolymer containing oil palm ash10.1155/2013/857586 ↗
17. Theoretical and experimental comparison of box solar cookers with and without internal reflector10.1016/j.egypro.2014.10.153 ↗
18. Influence of curing on the strength development of calcium-containing geopolymer mortar10.3390/ma6115069 ↗
19. Evaluating the optimum load range for box-type solar cookers10.1016/j.renene.2014.08.003 ↗
20. Effect of curing conditions on the strength of fly ash based self compacting geopolymer concrete
21. Effect of Na2SiO3/NaOH ratios and NaOH molarities on compressive strength of fly-ash-based geopolymer
22. The effect of curing temperature on physical and chemical properties of geopolymers10.1016/j.phpro.2011.11.045 ↗
23. Sustainability of concrete construction10.1061/(ASCE)1084-0680(2008)13:2(98) ↗
24. Solar cookers—cheap technology with high ecological benefits10.1016/0921-8009(96)00021-3 ↗
25. Influence of iron making slags on strength and microstructure of fly ash geopolymer10.1016/j.conbuildmat.2012.09.070 ↗
26. Fly ash/Kaolin based geopolymer green concretes and their mechanical properties10.1016/j.dib.2015.10.029 ↗
27. Effect of curing temperature and silicate concentration on fly-ash-based geopolymerization10.1021/ie051251p ↗
28. Low-calcium fly ash-based geopolymer concrete : reinforced beams and columns
29. Effect of types of curing on the strength of geopolymer concrete
30. Use of analytical techniques for identification of inorganic polymer gel composition10.1007/s10853-010-4257-2 ↗
31. Effect of partial replacement of fly ash by metakaolin on strength development of fly ash based geopolymer mortar