journal article·2019-01

Experimental study on the bond behavior between H-shaped steel and engineered cementitious composites

Liang Bai, Jipeng Yu, Miao Zhang, Tianhua Zhou

Publisher page

Abstract

Abstract This paper investigated the bond behavior of H-shaped steel embedded in engineered cementitious composites (ECC). The specimens were designed and subjected to a push-out test. The key parameters researched were the volume fraction of polyvinyl alcohol (PVA) fiber, stirrup reinforcement ratio, ECC cover thickness and H-shaped steel embedded length. The τ–S curves at the loaded end were obtained, and the strain distributions of the web and flange steel along the embedded length were analyzed. The results showed that the critical bond stress increased with the volume fraction of PVA fiber and that increasing the ECC cover thickness can significantly enhance the ultimate bond stress and residual bond stress. However, the ultimate bond stress declined slightly when the embedded length was increased. The stirrup reinforced ratio had little influence on the critical bond stress. The H-shaped steel developed inelastic behavior at the loaded end when the ECC cover thickness reached 70 mm or the embedded length reached 600 mm. The bond stress had a non-uniform distribution depending on the strain of the H-shaped steel. The critical points were defined to establish a bond stress-slip model, and the theoretical model coincided with test results well.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Tensile strain-hardening behavior of polyvinyl alcohol engineered cementitious composite (PVA-ECC)
2. Use of high volumes of fly ash to improve ECC mechanical properties and material greenness
3. On engineered cementitious composites (ECC): A review of the material and its applications
4. Mechanical behavior of ECC and ECC/RC composite columns under reversed cyclic loading10.1061/(ASCE)MT.1943-5533.0001950 ↗
5. Deformation behavior of fiber-reinforced polymer reinforced engineered cementitious composite (ECC) flexural members under reversed cyclic loading conditions
6. High-performance fiber-reinforced cement composites: an alternative for seismic design of structures
7. Effect of matrix ductility on deformation behavior of steel reinforced ECC flexural members under reversed cyclic loading conditions
8. Seismic response of exterior RC column-to-steel beam connections10.1061/(ASCE)0733-9445(2000)126:10(1113) ↗
9. Mechanical performance of steel reinforced UHTCC composite joint under static loading
10. Longitudinal shear resistance of PVA-ECC composite slabs10.1016/j.istruc.2015.12.003 ↗
11. M.M. Rana, C.K. Lee, S. Al-Deen, A study on the bond stress–slip behavior between engineered cementitious composites and structural steel sections. Proceedings of Eurosteel 2017, 13–15 September 2017, Copenhagen.v. 1, No. 2–3, pp. 2247–2256. https://doi.org/10.1002/cepa.27110.1002/cepa.271 ↗
12. Flexural behaviour of steel composite beams encased by engineered cementitious composites10.1016/j.jcsr.2018.01.004 ↗
13. Bond-splitting strength of reinforced strain-hardening cement composite elements with small bar spacing10.14359/51687228 ↗
14. Experimental and analytical investigation on bond-slip behavior of deformed bars embedded in engineered cementitious composites10.1016/j.conbuildmat.2016.10.036 ↗
15. Experimental study on bond–slip between ultra high toughness cementitious composites and steel bar
16. Experimental study on bond behaviour between BFRP bar and engineered cementitious composite10.1016/j.conbuildmat.2015.07.135 ↗
17. Local bond–slip response of GFRP rebar in ultra-high-performance fiber-reinforced concrete10.1016/j.compstruct.2014.09.055 ↗
18. Experimental study of bond behaviour between concrete and FRP bars using a pull-out test10.1016/j.compositesb.2009.07.003 ↗
19. Push-out test of pre-stressing concrete filled circular steel tube columns by means of expansive cement10.1016/j.conbuildmat.2007.10.021 ↗
20. Bond–slip behaviour between GFRP I-section and concrete10.1016/j.compositesb.2017.07.060 ↗
21. Shear connector requirements for embedded H-shaped steels10.1061/(ASCE)0733-9445(1999)125:2(142) ↗
22. Shear behavior of reinforced ultrahigh toughness cementitious composite beams without transverse reinforcement10.1061/(ASCE)MT.1943-5533.0000505 ↗
23. Code of China, Metallic materials-tensile testing at ambient temperature, GB/T228-2002, Beijing, 2002 (in Chinese).
24. Behavior and modeling of bond of FRP rebars to concrete10.1061/(ASCE)1090-0268(1997)1:2(40) ↗
25. Bond of high strength concrete with high strength reinforcing steel10.2174/1874149500802010143 ↗
26. Bond stress in embedded steel shapes in concrete. Composite and Mixed Construction
27. Wium · 1992
28. Introduction to grey system theory
29. A new approach to performance analysis of ejector refrigeration system using grey system theory10.1016/j.applthermaleng.2008.07.016 ↗
30. The use of the Taguchi method with grey relational analysis to optimize the thin-film sputtering process with multiple quality characteristic in color filter manufacturing10.1016/j.cie.2007.12.020 ↗
31. Application of grey relational analysis for corrosion failure of oil tubes10.1016/S0010-938X(00)00089-5 ↗