journal article·2019-02Open access

Porosity and electrical resistivity-based empirical calculation of the oxygen diffusion coefficient in concrete

P. Linares-Alemparte, C. Andrade, D. Baza

Abstract

Concrete carbonation induced by gas transport has an adverse effect on the service life of the steel-reinforced material. Gas tightness is crucial where concrete is used to contain radioactive materials and of utmost importance where acting as a radon barrier. Since as a rule gas travel inside concrete is governed either by diffusion or permeability, the material’s performance in that respect is assessed by analysing those two parameters. The gas diffusion coefficient in concrete is not readily found, however, due to the practical difficulties involved in preventing gas from leaking out of standard diffusion cells. An alternative approach is to measure permeability at high gas concentration and pressure. The existence of a relationship between the oxygen diffusion coefficient and permeability in OPC concrete was established by the authors in a previous paper. Diffusion has also been shown to be related to porosity and, in solutions, to electrical resistivity. Little is known, however, about the relationship between gas diffusion and resistivity where the pores may be filled not with a liquid, but with air. Inasmuch as resistivity is a non-destructive technique and porosity a property that can be readily measured, these two parameters could be used to directly assess concrete durability, its performance in nuclear facilities and its suitability as a radon barrier. This paper describes a study conducted to formulate equations from which to analytically determine the oxygen diffusion coefficient. These equations are derived from empirical measurements of oxygen diffusion coefficient, concrete porosity and electrical resistivity. The findings, which corroborate the existence of such relationships, were used to formulate an equation to calculate the diffusion coefficient directly from the experimental values of concrete porosity and resistivity. Since porosity depends primarily on concrete batching, curing and moisture content, two OPC concrete mixes were prepared using different water/cement ratios and two curing conditions. The combination resulted in four types of concrete. Pre-conditioning at three values of relative humidity was subsequently deployed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Geophysical Methods and Applications · Concrete Corrosion and Durability

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. Medina · 2007
2. Kropp · 1995
3. S. Darby et al., Radon in Homes and Risk of Lung Cancer: Collaborative Analysis of Individual Data FROM 13 European case-control Studies [on line], (Consulted: 16-06-2015), 2005.10.1136/bmj.38308.477650.63 ↗
4. Comparative risk or assessment of residential radon exposures in two radon-prone areas, Stei (Romania) and Torrelodones (Spain)10.1016/j.scitotenv.2009.04.033 ↗
5. Advances in characterization of gas transport in concrete: Determination of oxygen diffusion coefficient from permeability Coefficient and porosity. Service life and durability of reinforced concrete structures
6. AENOR · 2008
7. Permeability of concrete as a criterion of its durability. Final report: concrete durability – an approach towards performance testing
8. Types of models of service life of reinforcement: the case of the resistivity
9. Calculation of chloride diffusion coefficients in concrete from ionic migration measurements10.1016/0008-8846(93)90023-3 ↗
10. Permeability, diffusivity and microstructural parameters: a critical review10.1016/0008-8846(90)90101-3 ↗
11. C. Andrade et al., Calculation of tortuosity factor for the model based in concrete resistivity, in: Second International Conference on Microstructural-related Durability of Cementitious Composites, 11–13 April, Amsterdam, The Netherlands, 2012.
12. Influence of porosity and water content on the diffusivity of CO2 and O2 through hydrated cement paste10.1016/0008-8846(94)90040-X ↗
13. Oxygen diffusivity of various cementitious materials10.1016/0008-8846(91)90009-7 ↗
14. Moisture conditioning and transport properties of concrete test specimens10.1007/BF02473450 ↗
15. Measurement device and characteristics of diffusion coefficient of carbon dioxide in concrete
16. European Committee for Standardization · 2008
17. European Committee for Standardization · 2008
18. ASTM D4404, Standard Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry, 2010, ASTM.
19. ISO/TS 11665-13, Measurement of Radioactivity in the Environment – Air: Radon 222 – Part 13: Determination of the Diffusion Coefficient in Waterproof Materials: Membrane Two-side Activity Concentration Measurement Method, 2017, ISO.
20. Influence of mix proportions and components on the diffusion coefficient and the permeability of concrete