Performance optimization of hybrid fiber concrete according to mechanical properties
Source abstract
Abstract
Abstract In this research, interactional effects of four different fiber types, (steel, glass, synthetic and polypropylene) fly ash replacement ratio with cement, electrical arc furnace slag replacement ratio with natural aggregate and binder dosage on the mechanical properties (flexural and compressive strength, pull out capacity, resonance frequency and abrasion resistance) of Hybrid Fiber Concretes were investigated. The HFC samples were exposed to temperatures of 250 °C, 500 °C and 750 °C. The changes in the HFC samples after exposed to elevated temperature were determined by measuring the compressive strength and resonance frequency. 30 different experimental programs were conducted by using the central composite design method. By using experimental test results analysis of variance was performed and regression models obtained. The optimal combination was proposed by optimizing dependent variables and maximization of flexural and compressive strength, pull out capacity and resonance frequency while minimization of abrasion resistance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Concrete and Cement Materials Research · Recycled Aggregate Concrete Performance
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (57)
Show source-provided references
1. K. Walter, Strength and deformations of structural concrete subjected to in-plane shear and normal forces, Vol. 234, Birkhäuser, 2013.
2. High-performance fiber-reinforced concrete: a review10.1007/s10853-016-9917-4 ↗
3. B. Baradan, H. Yazıcı, S.Aydın, Beton, Dokuz Eylül University, Faculty of Engineering publications, 334, 2012.
4. Mechanical properties and fracture behavior of basalt and glass fiber reinforced concrete: an experimental study10.1016/j.conbuildmat.2015.10.006 ↗
5. Effect of pozzolanic materials on mechanical properties and aging of glass fiber reinforced concrete10.1016/j.conbuildmat.2019.07.128 ↗
6. Dynamic behavior of cement mortars reinforced with glass and basalt fibers10.1016/j.compositesb.2016.02.035 ↗
7. Mechanical behavior of high strength concrete reinforced with glass fiber reinforced polymer
8. Processing of high-performance fiber-reinforced cement-based composites10.1016/j.conbuildmat.2007.06.018 ↗
9. Effect of high temperatures on high performance steel fibre reinforced concrete10.1016/j.cemconres.2006.03.024 ↗
10. High performance fiber reinforced concrete for the shear reinforcement: experimental and numerical research10.1016/j.conbuildmat.2014.12.003 ↗
11. The effect of steel fibres on the enhancement of flexural and compressive toughness and fracture characteristics of oil palm shell concrete10.1016/j.conbuildmat.2013.12.103 ↗
12. Combined effect of silica fume and steel fiber on the mechanical properties of high strength concretes10.1016/j.conbuildmat.2007.04.017 ↗
13. Tensile behavior of ultra high performance hybrid fiber reinforced concrete10.1016/j.cemconcomp.2011.09.009 ↗
14. Mechanical properties of hybrid fiber-reinforced concrete at low fiber volume fraction10.1016/S0008-8846(02)00913-4 ↗
15. Study on mechanical properties of hybrid fiber reinforced concrete
16. Flexural behaviour of reinforced concrete beams with discrete steel–polypropylene fibres10.1051/matecconf/201710101020 ↗
17. A review of fiber synergy in hybrid fiber reinforced concrete
18. Effect of age on the compressive strength of ultra-high-performance fiber-reinforced concrete10.1016/j.conbuildmat.2018.04.203 ↗
19. Hybrid fiber reinforced self-compacting concrete with fly ash and colloidal nano silica: a systematic study10.1016/j.conbuildmat.2017.11.131 ↗
20. Application of response surface methodology and central composite design for the optimization of textile dye degradation by wet air oxidation10.1186/2228-5547-3-24 ↗
21. Biosorption of copper (II) ions on Enteromorpha prolifera: application of response surface methodology (RSM)10.1016/j.cej.2008.06.041 ↗
22. Parampalli, A., Eskridge, K., Smith, L., Meagher, M., Mowry, M., Subramanian, A., (2007) Development of serum-free media in CHO-DG44 cells using a central composite statistical design. Cytothecnology, 54, 57–68.10.1007/s10616-007-9074-3 ↗
23. Investigating the effect of mixture design parameters on pervious concrete by statistical modeling10.1016/j.conbuildmat.2012.07.044 ↗
24. Identifying the bond and abrasion behavior of alkali activated concretes by central composite design method10.1016/j.conbuildmat.2016.10.034 ↗
25. TS EN 12350-2 Testing fresh concrete - Part 2: Slump-test.
26. ASTM C1161, 2002. Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature. ASTM International, West Conshohocken, PA.
27. ASTM C 39, 1994. Standard test method for compressive strength of cylindrical concrete specimens. Annual Book of ASTM Standards.
28. ASTM C 215, 2003. Standard Test Method for Fundamental Transverse, Longitudinal, and Torsional Resonant Frequencies of Concrete Specimens, ASTM International, West Conshohocken, PA.
29. TS 2824 EN 1338, 2005. Zemin döşemesi için beton kaplama blokları - Gerekli şartlar ve deney metotlar, Türk Standartları Enstitüsü.
30. Optimum design of alkali activated slag concretes for the low oxygen/chloride ion permeability and thermal conductivity10.1016/j.compositesb.2016.01.047 ↗
31. Design-Expert, Software for design of experiments. USA: Stat-Ease Incorporation, Statistics Made Easy; 2007.
32. A.N. Junior, S.R. Ferreira, F. Toledo, R. D., Fairbairn, J. Dweck, Effect of early age curing carbonation on the mechanical properties and durability of high initial strength Portland cement and lime-pozolan composites reinforced with long sisal fibres, Composites Part B: Engineering, 163 (2019) 351-362. https://doi.org/10.1016/j.compositesb.2018.11.006.10.1016/j.compositesb.2018.11.006 ↗
33. Mechanical, flexural and microstructural properties of cement-tailings matrix composites: Effects of fiber type and dosage10.1016/j.compositesb.2019.05.039 ↗
34. Hybrid short fiber reinforcement system in concrete: a review10.1016/j.conbuildmat.2017.03.059 ↗
35. Statistical analysis of impact strength and strength reliability of steel-polypropylene hybrid fiber-reinforced concrete10.1016/j.conbuildmat.2004.05.002 ↗
36. Hybrid fiber reinforced concrete (HyFRC): Fiber synergy in high strength matrices10.1617/14095 ↗
37. Effects of hybrid fibers on the development of high volume fly ash cement composite10.1016/j.conbuildmat.2019.04.083 ↗
38. Ultrasonic evaluation of strength properties of cemented paste backfill: effects of mineral admixture and curing temperature10.1016/j.ultras.2019.105983 ↗
39. Fatigue cracking of polypropylene fiber reinforced concrete
40. Mechanical behaviour of fire-exposed fibre-reinforced sustainable concrete
41. An experimental and analytical investigation into age-dependent strength of fly ash mortar at elevated temperature10.1016/j.conbuildmat.2019.06.167 ↗
42. Fire response of hybrid fiber reinforced concrete to high temperature10.1016/j.proeng.2017.02.123 ↗
43. Modeling the effect of sulphate on strength development of paste backfill and binder mixture optimization10.1016/j.cemconres.2004.05.020 ↗
44. Performance of volcanic ash and pumice based blended cement concrete in mixed sulfate environment10.1016/j.cemconres.2006.03.010 ↗
45. Cemented paste backfill of sulphide-rich tailings: Importance of binder type and dosage10.1016/j.cemconcomp.2009.01.008 ↗
46. Pullout capacity development of cast in place anchors with embedded studs10.1016/j.conbuildmat.2015.10.166 ↗
47. The pull-out behavior of straight and hooked-end steel fiber from hybrid fiber reinforced cementitious composite: experimental study and analytical modeling10.1016/j.compstruct.2018.08.066 ↗
48. Nano-mechanical behavior of the interfacial transition zone between steel-polypropylene fiber and cement paste10.1016/j.conbuildmat.2017.04.035 ↗
49. Dynamic modulus of elasticity of geopolymer lightweight aggregate concrete10.1088/1757-899X/518/2/022023 ↗
50. Evaluation of residual mechanical properties of concrete after exposure to high temperatures using impact resonance method10.1016/j.conbuildmat.2016.10.116 ↗
51. Effect of nano silica and coir fiber on compressive strength and abrasion resistance of concrete10.1016/j.conbuildmat.2019.07.232 ↗
52. Effect of silica fume and slag on compressive strength and abrasion resistance of HVFA concrete10.1007/s40069-013-0051-2 ↗
53. Hydration and properties of sodium sulfate activated slag10.1016/j.cemconcomp.2012.12.010 ↗
54. Effect of metallic aggregate and cement content on abrasion resistance behaviour of concrete10.1179/143307511X12998222918877 ↗
55. K. Turk, M. Karatas, Abrasion resistance and mechanical properties of self-compacting concrete with different dosages of fly ash/silica fume, 18 (1) (2011) 49-60. http://nopr.niscair.res.in/handle/123456789/11206.
56. R.H. Myers, D.C. Montgomery, Response surface methodology process and product optimization using designed experiments, John Willey and Sons, 2002.
57. Bankir, Muzeyyen Balcikanli, and Umur Korkut Sevim. “Performance optimization of hybrid fiber concretes against acid and sulfate attack.” Journal of Building Engineering (2020): 101443.10.1016/j.jobe.2020.101443 ↗