A closed-form fracture model to predict tensile strength and fracture toughness of alkali-activated slag and fly ash blended concrete made by sea sand and recycled coarse aggregate
Source abstract
Abstract
Abstract A new type of concrete, namely alkali-activated slag and fly ash blended sea sand recycled aggregate concrete (AASRAC), is developed in this paper. By considering its future service under ocean environment, crack resistance of the new concrete should be emphasized and evaluated rationally. Similar to ordinary concrete, however, size effect would be inevitable in the determined tensile strength and fracture toughness based on traditional continuum mechanics. To address this issue, the intention of this paper is to propose an analytical fracture model to predict the tensile strength ft, fracture toughness KIC and energy GF by using tests on three-point-bending notched beams of AASRAC. The average aggregate size davg and two discrete numbers β and βw are introduced to represent the material heterogeneity and discontinuity, respectively. The critical effective crack propagation length and critical crack-tip opening displacement are quantified as the davg multiplied by β and βw, respectively, when the maximum applied load Fmax is reached. Closed-form solutions of the size-independent ft, KIC and GF are then obtained by using the experimentally measured Fmax based on boundary effect model. The means, and upper and lower bounds of the fracture parameters with 95% reliability are determined from the normal distribution analysis. Results show that the fracture parameters can be yielded with reasonable accuracy if β = 1.0 and βw = 1.0. The predicted ft, KIC and GF are higher as the slag-to-fly ash mass ratio increases in AASRAC. The predicted ft based on the proposed model is significantly larger than the traditional splitting tensile strength. The main failure mode of the tested AASRAC beam is that about 80% of the recycled coarse aggregates are fractured due to the improved interfacial micro-structures between the mortar and aggregates. The proposed model can give a rational design method for the new concrete.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Recycled Aggregate Concrete Performance · Concrete and Cement Materials Research · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (64)
Show source-provided references
1. A review on emission analysis in cement industries10.1016/j.rser.2011.02.014 ↗
2. Shi · 2006
3. Durability and life cycle evaluation of self-compacting concrete containing fly ash as GBFS replacement with alkali activation10.1016/j.conbuildmat.2019.117458 ↗
4. Mechanical strength and durability of alkali-activated fly ash/slag concrete
5. Properties and durability of alkali-activated slag concrete
6. Workability and mechanical properties of alkali activated slag concrete10.1016/S0008-8846(98)00236-1 ↗
7. Performance enhancement of recycled concrete aggregate-A review10.1016/j.jclepro.2015.08.057 ↗
8. Effects of combined usage of GGBS and fly ash on workability and mechanical properties of alkali activated geopolymer concrete with recycled aggregate10.1016/j.compositesb.2018.11.067 ↗
9. Physicochemical properties of alkali activated GGBS and fly ash geopolymeric recycled concrete10.1016/j.conbuildmat.2019.01.191 ↗
10. Use of recycled aggregates as internal curing agent for alkali-activated slag system10.1016/j.conbuildmat.2017.10.110 ↗
11. Construction and demolition waste as recycled aggregates in alkali-activated concretes10.3390/ma12234016 ↗
12. Influence of recycled concrete aggregates on alkali-activated slag mortar exposed to elevated temperatures
13. Influence of recycled concrete aggregates on the flexural properties of reinforced alkali activated slag concrete10.1016/j.conbuildmat.2015.10.148 ↗
14. Mechanical performance of CFRP-confined sustainable geopolymeric recycled concrete under axial compression10.1016/j.engstruct.2020.111246 ↗
15. Uniaxial compressive behaviors of fly ash/slag-based geopolymeric concrete with recycled aggregates10.1016/j.cemconcomp.2019.103375 ↗
16. Mechanical properties and microstructure analysis of fly ash geopolymeric recycled concrete10.1016/j.jhazmat.2012.07.070 ↗
17. Study on the optimum initial curing condition for fly ash and GGBS based geopolymer recycled aggregate concrete10.1016/j.conbuildmat.2020.118540 ↗
18. Experimental study of interfacial transition zones between geopolymer binder and recycled aggregate10.1016/j.conbuildmat.2018.02.111 ↗
19. Influence of recycled aggregate on fly ash geopolymer concrete properties10.1016/j.jclepro.2015.10.109 ↗
20. Influence of different monomer ratios and recycled concrete aggregate on mechanical properties and durability of geopolymer concretes10.1016/j.conbuildmat.2019.01.174 ↗
21. Use of recycled aggregates in pressed fly ash geopolymer concrete10.1002/ep.13327 ↗
22. Alkali activated slag concrete incorporating recycled aggregate concrete: long term performance and sustainability aspect10.1016/j.conbuildmat.2020.121512 ↗
23. Evaluation of the mechanical properties of sea sand-based geopolymer concrete and the corrosion of embedded steel bar10.1016/j.conbuildmat.2018.02.169 ↗
24. Recycled aggregate high calcium fly ash geopolymer concrete with inclusion of OPC and nano-SiO210.1016/j.conbuildmat.2018.04.123 ↗
25. Effect of fly ash and reactive MgO on the engineering properties and durability of high-performance concrete produced with alkali-activated slag and recycled aggregate10.1061/(ASCE)MT.1943-5533.0003420 ↗
26. Engineering performance of high-content MgO-Alkali-activated slag mortar incorporating fine recycled concrete aggregate and fly ash10.1007/s10163-020-01171-7 ↗
27. Mechanical and freezing cycles properties of geopolymer concrete with recycled aggregate10.1002/suco.201900317 ↗
28. Interfacial evaluation of geopolymer mortar prepared with recycled geopolymer fine aggregates10.1016/j.conbuildmat.2020.119849 ↗
29. Recycled geopolymer aggregates as coarse aggregates for Portland cement concrete and geopolymer concrete: Effects on mechanical properties10.1016/j.conbuildmat.2019.117571 ↗
30. Mechanical behavior of concrete using seawater and sea-sand with recycled coarse aggregates10.1002/suco.201900071 ↗
31. Mechanical properties of sea sand recycled aggregate concrete under axial compression10.1016/j.conbuildmat.2018.04.136 ↗
32. J.Z. Xiao, Q.X. Liao, Q.T. Zhang, C.B. Qiang, X. Liu, Bond behavior between seawater sea-sand recycled aggregate concrete and glass-fiber-reinforced polymer bars, J. Tongji Univ. (Natur. Sci.) 46 (7) (2018) 884-890; 971. (in Chinese).
33. Ductile, durable, and reliable alternative to FRP bars for reinforcing seawater sea-sand recycled concrete beams: steel/FRP composite bars10.1016/j.conbuildmat.2020.121264 ↗
34. Mechanical properties of alkali-activated slag concrete mixed by seawater and sea sand10.1016/j.conbuildmat.2018.11.113 ↗
35. Fracture behavior of recycled aggregate concrete under three-point bending10.1016/j.cemconcomp.2019.103353 ↗
36. Size effect in blunt fracture: concrete, rock, metal10.1061/(ASCE)0733-9399(1984)110:4(518) ↗
37. Tada · 2000
38. Determination of the fracture energy of mortar and concrete by means of three-point bend tests on notched beams
39. Universal size effect law and effect of crack depth on quasi-brittle structure strength10.1061/(ASCE)0733-9399(2009)135:2(78) ↗
40. Universal size-shape effect law based on comprehensive concrete fracture tests10.1061/(ASCE)EM.1943-7889.0000627 ↗
41. Critical comparison of the boundary effect model with cohesive crack model and size effect law10.1016/j.engfracmech.2019.04.036 ↗
42. Fracture energy and fracture process zone10.1007/BF02472590 ↗
43. Size effect on toughness induced by crack close to free surface10.1016/S0013-7944(99)00123-X ↗
44. Size effect and quasi-brittle fracture: the role of FPZ10.1007/s10704-008-9290-7 ↗
45. Granite strength and toughness from small notched three-point-bend specimens of geometry dissimilarity10.1016/j.engfracmech.2019.05.014 ↗
46. Statistics-assisted fracture modelling of small un-notched and large notched sandstone specimens with specimen-size/grain-size ratio from 30 to 90010.1016/j.engfracmech.2020.107134 ↗
47. Determination of fracture parameter and prediction of structural fracture using various concrete specimen types10.1016/j.tafmec.2019.01.008 ↗
48. Modelling and testing of large-scale masonry elements under three-point bending-Tough and strong nacre-like structure enlarged by a factor of 20,00010.1016/j.engfracmech.2020.106961 ↗
49. Size effect research of tensile strength of bamboo scrimber based on boundary effect model10.1016/j.engfracmech.2020.107319 ↗
50. A simple closed-form model for fracture of CFRP panel with shallow surface scratch confirmed by comprehensive flexural/tensile tests10.1016/j.mechmat.2020.103725 ↗
51. Effects of nano-grain structures and surface defects on fracture of micro-scaled polysilicon components10.1111/jace.17032 ↗
52. Boundary effect on concrete fracture and non-constant fracture energy distribution10.1016/S0013-7944(02)00223-0 ↗
53. Size-independent fracture energy in plain concrete beams using tri-linear model10.1016/j.conbuildmat.2011.01.003 ↗
54. Influence of local fracture energy distribution on maximum fracture load of three-point-bending notched concrete beams10.1016/j.engfracmech.2011.09.019 ↗
55. Correlation between cohesive crack-tip local fracture energy and peak load in mortar specimens10.1061/(ASCE)MT.1943-5533.0000959 ↗
56. An analytical approach to predict fracture parameters of coral aggregate concrete immersed in seawater10.1016/j.oceaneng.2019.106508 ↗
57. ASTM D1141-98, Standard Practice for the Preparation of Substitute Ocean Water. ASTM International, West Conshohocken, PA, 2013.
58. CS (Chinese Standard) GB/T 50081-2019, Standard for test method of physical and mechanical properties on concrete, China: Ministry of Construction of the People’s Republic of China and Quality Supervision Inspection and Quarantine of the People’s Republic of China; 2019, (in Chinese).
59. Properties of quicklime (CaO)-activated Class F fly ash with the use of CaCl210.1016/j.cemconres.2018.05.019 ↗
60. Effects of CaCl2 on hydration and properties of lime (CaO)-activated slag/fly ash binder10.1016/j.cemconcomp.2017.09.001 ↗
61. Properties of fresh and hardened fly ash/slag based geopolymer concrete: A review10.1016/j.jclepro.2020.122389 ↗
62. Physical-mechanical properties of fly ash/GGBFS geopolymer composites with recycled aggregates10.1016/j.conbuildmat.2019.07.211 ↗
63. Effects of activator properties and GGBFS/FA ratio on the structural build-up and rheology of AAC10.1016/j.cemconres.2020.106253 ↗
64. Design of geopolymer concrete with GGBFS at ambient curing condition using Taguchi method10.1016/j.conbuildmat.2017.02.131 ↗