The engineering properties of high performance concrete with HCWA–DSF supplementary binder
Source abstract
Abstract
Abstract High calcium wood ash (HCWA) and densified silica fume (DSF) exhibit good cementitious properties and has a great potential as supplementary binder material for the concrete production industry. The experimental investigation was conducted to study the properties of HCWADSF cement and the mechanical behaviour of HCWA–DSF high performance mortar. A total of twelve different blended cement pastes and mortar mixes were fabricated with the use of HCWA at various cement replacement levels of 0% to 20% in combination with 7.5% densified silica fume (DSF) by total binder weight and subjected to rheological and mechanical strength tests. The rheological properties of blended cement paste studied are standard consistency, initial setting time and final setting time. The mechanical strength parameters of mortar covered in the study are compressive strength, flexural strength, static modulus of elasticity and dynamic modulus of elasticity. Experimental results indicated that the inclusion of HCWA at the content of 2–20% by binder weight does not have significant influence on the standard consistency of HCWA–DSF blended cement but significantly prolonged the setting times of the blended cement paste. The combined use of HCWA (2–6% by binder weight) and DSF (7.5% by binder weight) as supplementary binder material produced mortar mixes which exhibited compressive and flexure strengths which are 2.4–31.2% higher than equivalent ordinary Portland cement (OPC) mortar. Besides, the use of HCWA at cement replacement levels between 2% and 12% with 7.5% DSF by weight of binder was found to enhance the static and dynamic modulus of Portland cement mortar by 1.9–24.7%. The observed improvement in the mechanical properties is due to a significant densification in the microstructure of cement paste matrix in the presence of HCWA and DSF hybrid supplementary binder as observed from micrographs obtained in the study.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Recycling and utilization of industrial and municipal waste in materials production · Magnesium Oxide Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Magin G. An introduction to wood waste in the UK. Fauna & Flora International, Cambridge, UK; 2001: p. 40.
2. Etiegni · 1990
3. Naik TR. Tests of wood ash as a potential source for construction materials. Report NoCBU-1999-09. Milwaukee: UWM Center for By-products utilization, Department of Civil Engineering and Mechanics, University of Wisconsin-Milwaukee; 1999. p. 61.
4. Physical and chemical characteristics of wood ash10.1016/0960-8524(91)90207-Z ↗
5. Potential of wood waste ash as an additive in concrete10.1061/(ASCE)0899-1561(2006)18:4(605) ↗
6. Effects of incorporation of sawdust incineration fly ash in cement pastes and mortars10.3130/jaabe.3.1 ↗
7. Ash from timber waste as cement replacement material10.1016/S0958-9465(01)00039-7 ↗
8. Characteristics of wood ash/OPC Concrete
9. Sawdust ash as concrete material10.1061/(ASCE)0899-1561(2002)14:2(173) ↗
10. Properties of high calcium wood ash and densified silica fume blended cement
11. Effects of incorporation of sawdust incineration fly ash in cement pastes and mortars10.3130/jaabe.3.1 ↗
12. Assessing of the fresh concrete properties of self-compacting concrete containing sawdust ash10.1016/j.conbuildmat.2007.02.004 ↗
13. Characterisation and use of biomass fly ash in cement-based materials10.1016/j.jhazmat.2009.07.109 ↗
14. Naik TR, Kraus RN, Siddique R. Demonstration of manufacturing technology for concrete and CLSM utilizing wood ash from Wisconsin. Report No CBU-2002-30 for Year 1 activities submitted to the Wisconsin Department of Natural Resources, Madison, WI, for Project No 01–06. Milwaukee: Department of Civil Engineering and Mechanics, University of Wisconsin-Milwaukee; 2002. p. 124.
15. An overview of the chemical composition of biomass10.1016/j.fuel.2009.10.022 ↗
16. Mechanical strength, durability and drying shrinkage of structural mortar containing HCWA as partial replacement of cement10.1016/j.conbuildmat.2011.12.009 ↗
17. Characterisation of high calcium wood ash for use as a constituent in wood ash–silica fume ternary blended cement10.4028/www.scientific.net/AMR.346.3 ↗
18. ASTM. ASTM C618–2003. Specifications for coal fly ash and raw or calcined natural pozzolan for use in concrete. Annual Book of ASTM Standards, vol 0402. West Conshohocken, PA, USA: American Society of Testing Materials; 2003.
19. ASTM. ASTM C150. Specifications for Portland cement. Annual Book of ASTM Standards, vol. 401. West Conshohocken, PA, USA: American Society of Testing Materials; 1997.
20. BSI. BS 812: Part 102. Testing aggregates. Method for sampling. London: British Standards Institution; 1989.
21. BSI. BS 882. Specification for aggregates from natural sources for concrete. London: British Standards Institution; 1992.
22. ASTM. ASTM C494. Standard specification for chemical admixtures for concrete. Annual Book of ASTM Standards, vol. 0402. West Conshohocken, PA, USA: American Society of Testing Materials; 2011.
23. BSI. BS EN 206: Part 1. Concrete. Specification, performance, production and conformity. London: British Standards Institution; 2000.
24. ASTM. ASTM C305. Practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency. Annual Book of ASTM Standards, vol 0401. West Conshohocken, PA, USA: American Society of Testing Materials; 1994.
25. BSI. BS EN 196: Part 3. Methods of testing cement. Determination of setting time and soundness. London: British Standards Institution; 2005.
26. ASTM. ASTM C469. Test method for static modulus of elasticity and Poisson’s ratio of concrete in compression. Annual Book of ASTM Standards, vol 0402. West Conshohocken, PA, USA: American Society of Testing Materials; 1994.
27. ASTM. ASTM C215. Standard test method for fundamental transverse, longitudinal and torsional resonant frequencies of concrete specimens. Annual Book of ASTM Standards, vol 0402. West Conshohocken, PA, USA: American Society of Testing Materials; 2002.
28. Comparison of methods for arresting hydration of cement10.1016/j.cemconres.2011.06.003 ↗
29. Preparing specimens for microscopy
30. Callister · 1999
31. Investigations on the performance of silica fume-incorporated cement pastes and mortars10.1016/S0008-8846(03)00171-6 ↗
32. Utilization of fly ash with silica fume and properties of Portland cement-fly ash–silica fume concrete10.1016/j.fuel.2009.10.003 ↗
33. Basic rheological and mechanical properties of high-volume fly ash grouts10.1016/S0950-0618(02)00026-0 ↗
34. Activation of fly ash cementitious systems in the presence of quicklime: Part I. Compressive strength and pozzolanic reaction rate10.1016/j.cemconres.2003.08.008 ↗
35. Activation of fly ash cementitious systems in the presence of quicklime. Part II: Nature of hydration products, porosity and microstructure development10.1016/j.cemconres.2006.09.013 ↗
36. Effect of lime putty addition on structural and durability properties of concrete10.1016/S0008-8846(01)00744-X ↗
37. Influence of initial curing on the properties of concrete containing limestone blended cement10.1016/S0008-8846(00)00217-9 ↗
38. Swamy RN, Sakai N, Nakamura N. Role of superplasticizer and slag for producing high performance concrete. In: Malhotra VM, editor. 4th CANMET/ACI international conference on superplasticizers and other chemicals in concrete: American Concrete Institute; 1994. p. 1–26.
39. Swamy RN. Durability of concrete composites with polymer. In: Gemert DV, editor. In: 8th international congress on polymers in concrete. Oostende; 1995. p. 21–6.
40. Strength development of ternary blended cement with limestone filler and blast-furnace slag10.1016/S0958-9465(01)00056-7 ↗
41. The role of calcium carbonate in cement hydration10.1016/j.cemconres.2006.10.013 ↗
42. Studies on the carboaluminate formation in limestone filler-blended cements10.1016/S0008-8846(01)00491-4 ↗
43. Thermodynamic properties of Portland cement hydrates in the system CaO–Al2O3–SiO2–CaSO4–CaCO3–H2O10.1016/j.cemconres.2007.06.002 ↗
44. Moir G. Cements. In: Newman J, Ban SC, editors. Advanced Conrete Technology – Constituent Material. U.K: Butterworth Heinemann; 2003.10.1016/B978-075065686-3/50277-9 ↗