Study of alkali-activated mortar used as conventional repair in reinforced concrete
Source abstract
Abstract
Abstract Alkali-activated mortar (AAM) is a growing interest material as an environmentally friendly alternative to the conventional one. In this study, the use of AAM was investigated as repair material to conventional concrete. Reinforced concrete beams of 150 mm wide × 150 mm high × 500 mm long were produced to be repaired by the AAM. The concrete substrates and the AAM mortar were characterized, and the flexural strengths of the reinforced concrete beams with and without the repair were obtained (bending stress curves). The results showed that AAM developed a fast and good strength (30 MPa after 24 h) and had good adherence to the substrate. AAM had good performance and promoted strength increase. This study indicates the possibility of using an AAM as a repair material to conventional concrete substrate.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Concrete Corrosion and Durability · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Effect of mix composition on workability and compressive strength of self-compacting geopolymer concrete10.1139/l11-077 ↗
2. Assessment of alkali activated mortars based on different precursors with regard to their suitability for concrete repair10.1016/j.conbuildmat.2016.08.018 ↗
3. A novel waterproof, fast setting and high early strength repair material derived from metakaolin geopolymer10.1016/j.conbuildmat.2016.07.058 ↗
4. Compatibility of repair mortars with concrete in a hot-dry environment10.1016/S0958-9465(00)00073-1 ↗
5. High calcium fly ash geopolymer mortar containing Portland cement for use as repair material10.1016/j.conbuildmat.2015.08.139 ↗
6. Thermal behavior and mechanical properties of geopolymer mortar after exposure to elevated temperatures10.1016/j.conbuildmat.2016.01.043 ↗
7. A review: The comparison between alkali-activated slag (Si + Ca) and metakaolin (Si + Al) cements10.1016/j.cemconres.2010.03.020 ↗
8. Bond strength of PCC pavement repairs using metakaolin-based geopolymer mortar10.1016/j.cemconcomp.2015.10.009 ↗
9. Durability of alkali-activated materials: progress and perspectives10.1111/jace.12831 ↗
10. Advancing the use of secondary inputs in geopolymer binders for sustainable cementitious composites: a review10.3390/su3020410 ↗
11. Activating solution chemistry for geopolymers
12. New geopolymeric binder based on fluid catalytic cracking catalyst residue (FCC)10.1016/j.matlet.2012.04.051 ↗
13. Durability and microstructure characteristics of alkali activated coal bottom ash geopolymer cement10.1016/j.jclepro.2014.06.037 ↗
14. Carbon dioxide equivalent (CO2-e) emissions: a comparison between geopolymer and OPC cement concrete10.1016/j.conbuildmat.2013.01.023 ↗
15. Water treatment sludge and rice husk ash to sustainable geopolymer production10.1016/j.jclepro.2017.02.076 ↗
16. Activation of metakaolin/slag blends using alkaline solutions based on chemically modified silica fume and rice husk ash10.1007/s12649-011-9093-3 ↗
17. Bonding and abrasion resistance of geopolymeric repair material made with steel slag10.1016/j.cemconcomp.2007.04.004 ↗
18. NBR NM 248, Aggregates – Sieve Analysis of Fine and Coarse Aggregates, Brazilian Assoc. Tech. Stand., 2003.
19. NBR NM 52, Fine Aggregate – Determination of the Bulk Specific Gravity and Apparent Specific Gravity, Brazilian Assoc. Tech. Stand., 2009.
20. NBR NM 53, Coarse Aggregate – Determination of the Bulk Specific Gravity, Apparent Specific Gravity and Water Absorption, Brazilian Assoc. Tech. Stand., 2009.
21. NBR NM 46, Aggregates – Determination of Material Finer than 75 μm Sieve by Washing, Brazilian Assoc. Tech. Stand., 2003.
22. NBR NM 67, Concrete – Slump Test for Determination of the Consistency, Brazilian Assoc. Tech. Stand., 1998.
23. NBR 5739, Concrete – Compression Test of Cylindric Specimens – Method of Test, Brazilian Assoc. Tech. Stand., 2007.
24. NBR 13278, Mortars Applied on Walls and Ceilings – Determination of the Specific Gravity and the Air Entrained Content in the Fresh Stage, Brazilian Assoc. Tech. Stand., 2005.
25. NBR 13276, Mortars Applied on Walls and Ceilings – Determination of the Consistence Index, Brazilian Assoc. Tech. Stand., 2016.
26. NBR 13279, Mortars Applied on Walls and Ceilings – Determination of the Flexural and the Compressive Strength in the Hardened Stage, Brazilian Assoc. Tech. Stand., 2005.
27. Influence of loading history upon the compressive properties of concrete10.1680/macr.1980.32.111.89 ↗
28. Shear behaviour of recycled aggregate concrete beams with and without shear reinforcement10.1016/j.engstruct.2017.03.026 ↗
29. Shear strength of longitudinally reinforced recycled aggregate concrete beams10.1016/j.engstruct.2017.05.028 ↗
30. Use of polymer modified mortar in controlling cracks in reinforced concrete beams10.1016/j.conbuildmat.2011.08.023 ↗
31. Design equations for axially loaded reinforced concrete columns strengthened with fibre reinforced polymer wraps10.1139/l00-019 ↗
32. Geopolymer mortars as sustainable repair material: a comprehensive review10.1016/j.rser.2017.05.076 ↗