journal article·2020-10Open access

Enhancement of the concrete-PCM interfacial bonding strength using silica fume

Mahmudul Hasan Mizan, Tamon Ueda, Koji Matsumoto

Abstract

Recently, the polymer cement mortar (PCM) overlaying method has gained popularity as a repair/retrofitting technique. The debonding issue at the interface hinders the worldwide application of this strengthening method. Accompanying the occurrence of debonding at the interface, the strengthening effect of the PCM is lost, causing a sudden decrease in the load-carrying capacity. To prevent premature debonding, this study aims to enhance the concrete-PCM interface by using silica fume. The bi-surface shear test was selected as the test method, and three levels of surface roughness (highest level with sandblasting, medium and lowest levels with steel wire brushing) and two different concrete compressive strengths (low strength type (LS) with 16.73 MPa and normal strength type (NS) with 29.59 MPa) were given as experimental parameters. When the surface is roughened by sandblasting, the specimens with 5% silica PCM increase the interfacial strength compared to that of the normal PCM cases by approximately 36.84% and 35.05% for the "LS" and "NS" types of concrete, respectively. The percentage increase is even higher when the surface is roughened by steel wire brushing (high and low), with an increase of approximately 135.35% and 181.12%, respectively. This fact indicates that silica fume inclusions can enhance the chemical bonding at the concrete-PCM interface. The mixing of silica fume in PCM and a higher surface roughness level shifts the pure interface failure (I) mode closer to the concrete cohesion (C) failure mode for "LS" type concrete and to the composite fracture mode (I-P) for "NS" type concrete. Conclusively, it is confirmed that mixing silica fume into PCM strengthened the interface bonding strength.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Microbial Applications in Construction Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. T. Aravinthan, T. Heldt, Innovative strengthening technique using prestressed fiber wraps for bridge headstocks, in: Proceedings of Australian Structural Engineering Conference, ISBN: 1877040371. (2005), 310–319.
2. Prediction of the post-peak behavior of reinforced concrete columns with and without FRP-jacketing10.1016/j.engstruct.2013.05.049 ↗
3. Effective method of repairing RC beam using externally bonded steel plate10.4028/www.scientific.net/AMM.567.399 ↗
4. Problems associated with plate bonding methods of strengthening reinforced concrete beams
5. Shear-peeling bond strength between continuous fibre sheet and concrete
6. Textile reinforced concrete for strengthening in bending and shear
7. Fibre-reinforced cement-based composite sheets for structural retrofit
8. Investigation on the bond behavior between PBO-FRCM strengthening material and concrete10.3151/jact.12.545 ↗
9. Zhang · 2009
10. Miura · 2017
11. Composite mechanism of polymer modified cement10.1016/0008-8846(94)00120-N ↗
12. Influence of polymer type on adhesion performance of blended cement mortar10.1016/j.ijadhadh.2013.01.007 ↗
13. Intermediate crack debonding of polymer cement mortar overlay-strengthened RC beam10.1061/(ASCE)MT.1943-5533.0000240 ↗
14. Concrete cover separation failure of overlay strengthened reinforced concrete beams10.1016/j.conbuildmat.2011.06.082 ↗
15. Central peeling failure behavior of polymer cement mortar retrofitting of reinforced concrete beams10.1061/(ASCE)0899-1561(2005)17:2(126) ↗
16. Recommended improvements to current shear friction provisions of model code
17. Testing the bond between repair materials and concrete substrate
18. A state-of-the-art review of roughness quantification methods for concrete surfaces10.1016/j.conbuildmat.2012.09.045 ↗
19. Tensile bond testing of concrete repairs10.1007/BF02473259 ↗
20. Influence of interface roughness on PCM-concrete interfacial fracture parameters
21. The effect of silica fume on the properties of concrete as defined in Concrete Society Report 74, cementitious materials
22. The tricalcium silicate hydration in the presence of active silica10.1016/0008-8846(83)90033-9 ↗
23. Influence of pozzolans on the hydration of C3A
24. Effect of reaction ratio of silica fume on strength development of 150N/mm2 class concrete
25. A study on the effect of silica fume and surface penetrant on bonding strength for overlaying10.18702/acf.2019.06.30.1 ↗
26. Kanezuka · 2005
27. Fuji chemical Co. Ltd. (2009). Guideline on the Procedure of the Application of Silicate-Based Surface Penetrant Over the Concrete Surface, Japan.
28. Effects of Temperature and moisture on concrete-PCM interface performance
29. Investigation on concrete-PCM interface under elevated temperature: at material level and member level10.1016/j.conbuildmat.2016.08.067 ↗
30. Fracture mechanisms of polymer cement mortar: concrete interfaces
31. Ohama · 1995
32. ASTM C39/39 M-05 (2013). Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. American Standard of Testing Materials.
33. Bi-surface shear test for evaluating bond between existing and new concrete
34. P.M.D. Santos, E.B.S. Júlio, Assessment of the Shear Strength between Concrete Layers, in: 8th fib International Ph.D. Symposium in Civil Engineering, Denmark, (2010) pp. 1–6.
35. A study of prototype of simple loading device giving pure shear force
36. Rui · 2012
37. Experimental evaluation of concrete-to-UHPC bond strength with correlation to surface roughness for repair application
38. Study on the bonding properties of Engineered Cementitious Composites (ECC) and existing concrete exposed to high temperature10.1016/j.conbuildmat.2018.11.136 ↗
39. Investigation of interface shear properties and mechanical model between ECC and concrete10.1016/j.conbuildmat.2019.06.188 ↗
40. Investigation of the bond between the concrete substrate and ECC overlays10.1061/(ASCE)MT.1943-5533.0000805 ↗
41. Experiment study on fracture property of ECC-concrete interface
42. Evaluation of tensile bonding strength between UHTCC repair materials and concrete substrate10.1016/j.conbuildmat.2016.02.149 ↗
43. Experimental and analytical investigations on the behavior of the interface between concrete and polymer cement mortar under hygrothermal conditions10.1016/j.conbuildmat.2015.07.035 ↗