journal article·2020-01

Effect of loading rates on bond behaviour between basalt fibre-reinforced polymer bars and concrete

Wei Wei, Feng Liu, Zhe Xiong, Fei Yang, Lijuan Li, Hanwei Luo

Publisher page

Abstract

Abstract In this study, bond performance between basalt fibre-reinforced polymer bars and sea sand concrete was investigated using pull-out tests that considered two parameters, loading rate and concrete type. All pull-out specimens exhibited a pull-out failure mode. Moreover, bond mechanism, bond strength, slip, and bond stress–slip curve are discussed. The bond behaviour was found to be sensitive to the loading rate. The bond mechanism was controlled by mechanical interlocking at static loading rate, friction at the earthquake loading rate, and chemical adhesion and the shear strength of the fibre layers at impact loading rate. The bond strength with a high-speed loading rate was lower than that with a static loading rate. The variation trends for the bond strength and slip differed with the type of loading rate. Finally, formulae are proposed for estimating a dynamic influence factor, which is used to evaluate the influence of the strain rate on the bond strength and slip.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Innovative concrete reinforcement materials · Structural Response to Dynamic Loads

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Investigation on the interfacial behaviour between the rubber-cement matrix of the rubberized concrete10.1016/j.jclepro.2018.10.305 ↗
2. Experimental investigation on the behavior of GFRP-RAC-steel double-skin tubular columns under axial compression10.1016/j.tws.2018.08.026 ↗
3. Effects of combined usage of GGBS and fly ash on workability and mechanical properties of alkali activated geopolymer concrete with recycled aggregate10.1016/j.compositesb.2018.11.067 ↗
4. Filler technology of adding granite dust to reduce cement content and increase strength of mortar10.1016/j.powtec.2018.09.084 ↗
5. Utilization of unprocessed steel slag as fine aggregate in normal- and high-strength concrete10.1016/j.conbuildmat.2019.01.178 ↗
6. Impact performance of new prestressed high-performance concrete pipe piles manufactured with an environmentally friendly technique10.1016/j.jclepro.2019.05.241 ↗
7. A multiphase internal state variable model with rate equations for predicting elastothermoviscoplasticity and damage of fiber-reinforced polymer composites10.1007/s00707-018-2358-1 ↗
8. A review on basalt fibre and its composites10.1016/j.compositesb.2014.12.034 ↗
9. Bond behavior between BFRP bar and recycled aggregate concrete reinforced with basalt fiber10.1016/j.conbuildmat.2016.12.161 ↗
10. Bond mechanism and bond strength of GFRP bars to concrete: a review10.1016/j.compositesb.2016.04.068 ↗
11. ACI · 2006
12. Canadian Standards Association, Design and construction of building components with fiber-reinforced polymers (CAN/CSA-S806-02), Toronto, Ontario, Canada, 2002.
13. Canadian Highway Bridge Design Code, Design and construction of building structures with fiber reinforced polymers (CAN/CSA S6-06), Mississauga, Ontario, Canada, 2006.
14. Japan Society of Civil Engineers, Test method for bond properties of continuous fiber sheets to concrete (JSCE-E-543-2000), Tokyo, Japan: Research Committee on Upgrading of Concrete Structures with Use of Continuous Fiber Sheets, 2001.
15. Bond strength of fiber reinforced polymer rebars in normal strength concrete10.1061/(ASCE)1090-0268(2005)9:3(203) ↗
16. Bond performance of basalt fiber-reinforced polymer bars to concrete10.1061/(ASCE)CC.1943-5614.0000487 ↗
17. Experimental study of bond behaviour between concrete and FRP bars using a pull-out test10.1016/j.compositesb.2009.07.003 ↗
18. Improved bond equations for fiber-reinforced polymer bars in concrete10.3390/ma9090737 ↗
19. Bond performances of FRP rebars-reinforced concrete10.1061/(ASCE)0899-1561(2007)19:3(205) ↗
20. Experimental investigations on the bond behavior between concrete and FRP reinforcing bars10.1016/j.conbuildmat.2018.03.169 ↗
21. Bond behavior of fiber reinforced polymer bars under direct pullout conditions10.1061/(ASCE)1090-0268(2004)8:2(173) ↗
22. Eligehausen · 1983
23. Behavior and modeling of bond of FRP rebars to concrete10.1061/(ASCE)1090-0268(1997)1:2(40) ↗
24. E. Cosenza, G. Manfredi, R. Realfonzo, Analytical modelling of bond between FRP reinforcing bars and concrete, In: Taerwe L, editor. Proc., 2nd int. RILEM symp. (FRPRCS-2); 1995.
25. Evaluation of bond stress-slip models for FRP reinforcing bars in concrete10.1016/j.compstruct.2013.07.037 ↗
26. Bond performance of GFRP and deformed steel hybrid bar with sand coating to concrete10.1177/0731684416684209 ↗
27. Bond performance between fibre-reinforced polymer bars and concrete under pull-out tests10.1016/j.conbuildmat.2019.116803 ↗
28. Long-term bond durability of fiber-reinforced polymer bars embedded in seawater sea-sand concrete under ocean environments10.1061/(ASCE)CC.1943-5614.0000876 ↗
29. Bond durability of BFRP bars embedded in concrete under seawater conditions and the long-term bond strength prediction10.1016/j.matdes.2015.12.066 ↗
30. Mechanical properties of alkali-activated slag concrete mixed by seawater and sea sand10.1016/j.conbuildmat.2018.11.113 ↗
31. Study on bond performance between FRP bars and seawater coral aggregate concrete10.1016/j.conbuildmat.2018.04.015 ↗
32. Experimental study on the bond durability between steel-FRP composite bars (SFCBs) and sea sand concrete in ocean environment10.1016/j.conbuildmat.2016.04.052 ↗
33. Bond durability of steel-FRP composite bars embedded in seawater sea-sand concrete under constant bending and shearing stress10.1016/j.conbuildmat.2018.10.154 ↗
34. Strain rate studies of pultruded glass fibre reinforced polymer material properties: a literature review10.1016/j.conbuildmat.2018.03.113 ↗
35. M. Belaoura, Compressive behaviour of concrete at high strain rates, COST Action C26 International Conference on Urban Habitat Constructions Under Catastrophic Events, Naples, Italy, 2010.
36. Static and impact behaviour of recycled aggregate concrete under daily temperature variations10.1016/j.jclepro.2018.04.237 ↗
37. Strain rate and temperature effects on the dynamic tensile behaviors of basalt fiber bundles and reinforced polymer composite10.1061/(ASCE)MT.1943-5533.0001615 ↗
38. Mechanical properties and failure characteristics of CFRP under intermediate strain rates and varying temperatures10.1016/j.compositesb.2016.03.085 ↗
39. Effect of loading rate and chemical corrosion on the mechanical properties of large diameter glass/basalt-glass FRP bars10.1016/j.conbuildmat.2015.05.044 ↗
40. Fiber-reinforced polymer bars under freeze-thaw cycles and different loading rates10.1177/0021998306063154 ↗
41. Effect of loading rates on pullout behavior of high strength steel fibers embedded in ultra-high performance concrete10.1016/j.cemconcomp.2016.03.014 ↗
42. Bond behaviour between corroded steel bars and concrete under different strain rates10.1680/jmacr.15.00174 ↗
43. Identification of the structural damage mechanism of BFRP bars reinforced concrete beams using smart transducers based on time reversal method10.1016/j.conbuildmat.2019.06.056 ↗
44. Serviceability of one-way high-volume fly ash-self-compacting concrete slabs reinforced with basalt FRP bars10.1016/j.conbuildmat.2019.05.044 ↗
45. Compressive behaviour of concrete at high strain rates10.1007/BF02472016 ↗
46. Strain rate effects in composites10.1115/1.3101860 ↗
47. P. Barata, C. Rigueiro, A. Santiago, J. P. Rodrigues, Impact loads in steel connections, IABSE Symposium Report, 100(4) (2013), 242–249, Doi: 10.2749/222137813807054601.10.2749/222137813807054601 ↗
48. A modified servo-hydraulic machine for testing at intermediate strain rates10.1016/j.ijimpeng.2008.06.003 ↗