On low-velocity impact response of SIFCON slabs under drop hammer impact loading
Source abstract
Abstract
Abstract The response of thin slabs of Slurry-Infiltrated Fibrous Concrete (SIFCON) with and without reinforcement under low velocity impacts is explored via drop-hammer impact experiments. For comparison purpose, plain cement concrete (PCC) and reinforced cement concrete (RCC) slabs were also cast and tested. To produce SIFCON slabs made with binary cementitious materials, the pre-determined concrete mixtures were designed with 15% of silica fume, 30% of blast furnace as a partial substitute of cement along with a constant 10% of hooked end steel fibres by volume fraction. The replication of a low-velocity impact on slab was achieved by dropping a steel ball (weighing 4.5 kg), with fall height of 457 mm, via the utilization of a self-fabricated drop-hammer impact test device. The parameters like first crack and ultimate failure energy absorption capacity, ultimate crack resistance, crack resistance ratio, ductility indices, and failure pattern were examined. The test results reported that the incorporation of binary blends of silica fume and slag in SIFCON matrix shows better performance in terms of strength and durability characteristics.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Innovative concrete reinforcement materials · High-Velocity Impact and Material Behavior · Structural Response to Dynamic Loads
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Fracture and impact properties of short discrete jute fibre- reinforced cementitious composites10.1016/j.matdes.2013.01.029 ↗
2. The influence of silica fume and curing regime on some properties of concrete
3. Stress-strain properties of SIFCON in compression
4. Effect of mineral admixtures and steel fiber volume contents on the behaviour of high performance fiber reinforced concrete10.1016/j.matdes.2014.06.066 ↗
5. Influence of silica fume on high strength lightweight concrete
6. Combined effect of silica fume and steel fiber on the mechanical properties of high strength concrete10.1016/j.conbuildmat.2007.04.017 ↗
7. Efficiency of GGBS in concrete10.1016/S0008-8846(00)00271-4 ↗
8. An experimental study on optimum usage of GGBS for the compressive strength of concrete10.1016/j.cemconcomp.2007.01.001 ↗
9. Influence of mineral additions on the physical mechanical properties of concretes
10. Behaviour of high volume fiber cement mortar in flexure10.1016/0958-9465(90)90008-L ↗
11. Improvement on SIFCON performance by fiber orientation and high-volume mineral admixtures10.1061/(ASCE)MT.1943-5533.0000114 ↗
12. Autoclaved SIFCON with high volume Class C fly ash binder phase10.1016/j.cemconres.2005.10.002 ↗
13. Pull-out behavior of single steel fiber from SIFCON matrix10.1016/j.conbuildmat.2012.04.110 ↗
14. Study on exterior RC beam-column joints upgrade with SIFCON in joint core under reversed cyclic loading10.1007/s12205-016-0643-x ↗
15. Performance characteristics of SIFCON plates
16. Ductile behavior of SIFCON structural members
17. Preparation, properties and application of cement-based composites containing 5 to 20 percent steel fibre
18. Response of SIFCON two-way slabs under impact loading10.1016/j.ijimpeng.2009.06.003 ↗
19. Behaviour of slurry infiltrated fibrous concrete (SIFCON) on simply supported two way slabs in flexure
20. Behaviour of steel reinforced slurry infiltrated fibrous concrete (SIFCON) two way slabs in punching shear
21. BIS: 12269. 1987. Specification for ordinary Portland cement, New Delhi -Reaffirmed 1999.
22. ASTM International, C1585-13, Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes.
23. IS 456-2000- Plain and reinforced concrete – code of practice (Fourth revision).
24. ASTM C1240-15 Standard Specification for Silica Fume Used in Cementitious Mixtures.
25. ASTM C989, Standard Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars.
26. ACI Committee 544.2R-89. Measurement of properties of fiber reinforced concrete.