journal article·2020-05

Development and evaluation of a surface-densified wood composite with an asymmetric structure

Chuanfu Chen, Dengyun Tu, Qiaofang Zhou, Jianhui Zhou, Xianju Wang, Banyat Cherdchim, Rongxian Ou

Publisher page

Abstract

Abstract This study aimed to develop a novel wood composite with an asymmetric structure by surface densification technology. A series of single-surface densified wood specimens were prepared by the hot-pressing process. The impact of effective dense layer on their physical and mechanical properties were investigated. The results indicated that the mechanical properties of densified wood were dependent on the effective dense layer thickness and position. The surface hardness and impact resistance are higher than some hardwood species often used for solid wood flooring. In addition, the cell lumen volume in densified layer was significantly reduced compared to that of the un-densified layer.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Wood Treatment and Properties · Natural Fiber Reinforced Composites · Lignin and Wood Chemistry

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Thermo-mechanical densification of Populus tomentosa var. tomentosa with Low moisture content10.15376/biores.9.3.3846-3856 ↗
2. Effects of preheating temperatures on the formation of sandwich compression and density distribution in the compressed wood10.1007/s10086-018-1758-0 ↗
3. Research progress of poplar wood enhanced modification in fast-growing plantation
4. Interactive effect of surface densification and post-heat-treatment on aspen wood10.1016/j.jmatprotec.2009.09.013 ↗
5. The influence of process parameters on the density profile and hardness of surface-densified birch wood (Betula pendula Roth)10.15376/biores.12.3.6011-6023 ↗
6. Effect of thermal modification by hot pressing on performance properties of paulownia wood boards10.1016/j.indcrop.2012.12.024 ↗
7. Wood modification technologies - a review10.3832/ifor2380-010 ↗
8. Preparation of hydro-thermal surface-densified plywood inspired by the stiffness difference in “sandwich structure” of wood10.1016/j.conbuildmat.2018.05.135 ↗
9. Influence of pressing parameters on dimensional stability and density of compressed beech wood10.1007/s00107-018-1298-8 ↗
10. Surface modification of wood using friction
11. Needle fir wood modified by surface densification and thermal post-treatment: hygroscopicity and swelling behavior10.1007/s00107-015-0969-y ↗
12. Surface densification of acetylated wood10.1007/s00107-016-1077-3 ↗
13. Cupping behaviour of surface densified scots pine wood: the effect of process parameters and correlation with density profile characteristics10.1007/s10853-013-7443-1 ↗
14. Densification of wood veneers by compression combined with heat and steam10.1007/s00107-011-0524-4 ↗
15. Sandwich compression of wood: control of creating density gradient on lumber thickness and properties of compressed wood10.1007/s00226-016-0824-2 ↗
16. Wettability and roughness characteristics of modified wood boards using a hot-press10.1016/j.indcrop.2011.04.024 ↗
17. Surface modification of Scots pine: the effect of process parameters on the through thickness density profile10.1007/s10853-011-5388-9 ↗
18. Optimization of pressing parameters for mechanically surface-densified aspen
19. Micromorphological studies of surface densified wood10.1007/s10853-013-7890-8 ↗
20. Hardness and density profile of surface densified and thermally modified Scots pine in relation to degree of densification10.1007/s10853-012-7019-5 ↗
21. Influence of temperature of thermal treatment on surface densification of spruce10.1007/s00107-016-1052-z ↗
22. Influence of veneer densification on the shear strength and temperature behavior inside the plywood during hot press10.1016/j.conbuildmat.2017.11.161 ↗
23. Sandwich-structured wood flour/HDPE composite panels: Reinforcement using a linear low-density polyethylene core layer10.1016/j.conbuildmat.2017.12.246 ↗
24. Structural behaviour of glued laminated timber beams pre-stressed by compressed wood10.1016/j.conbuildmat.2011.10.002 ↗
25. Research Institute of Wood Industry · 1982
26. Physical and mechanical properties of wood-Test methods for small clear wood specimens-Part 12
27. GB, T 17657 · 2013
28. ISO 13061–2 · 2014
29. ISO 13061–4 · 2014
30. Measuring the thickness swelling and set-recovery of densified and thermally modified Scots pine solid wood10.1007/s10853-013-7671-4 ↗
31. Wood densification and thermal modification: hardness, set-recovery and micromorphology10.1007/s00226-016-0835-z ↗
32. The effect of process parameters on the hardness of surface densified Scots pine solid wood10.1007/s00107-012-0649-0 ↗
33. Moisture dependent softening behavior of wood
34. Continuous surface densification of wood: a new concept for large-scale industrial processing10.15376/biores.12.2.3122-3132 ↗
35. Influence of temperature of thermal treatment on surface densification of spruce10.1007/s00107-016-1052-z ↗
36. Impact resistance and damage characteristics of composite laminates10.1016/S0263-8223(03)00114-4 ↗
37. Drop-weight impact response of hybrid composites impacted by impactor of various geometries10.1016/j.matdes.2013.05.016 ↗
38. Processing bulk natural wood into a high-performance structural material10.1038/nature25476 ↗