The laboratory evaluation of incorporating ceramsite into HMA as fine aggregates
Source abstract
Abstract
Abstract The aim of this paper is to explore hot asphalt mixture (HMA) with potential cooling capacity through adding ceramsite. Ceramsite asphalt mixtures (CAM) are prepared by adding ceramsite to replace fine aggregate with different ratio. Marshall and pavement performance tests were performed to test the pavement performance of CAM. Indoor radiation and outdoor radiation tests are carried out to evaluate the thermal properties of CAM. Results indicate that the Marshall Stability and dynamic stability of CAM increase with the increasing ceramsite ratio from 0% to 60%. The retained MS and low temperature performance of CAM nearly do not change with ceramsite ratio, but the tensile strength ratio decreases with ceramsite ratio. However, all values of the tensile strength ratio are above the requirements of specification. In the aspect of the thermal properties of CAM, the addition of ceramsite can effectively reduce the thermal conductivity of asphalt mixtures. Also, ceramsite is helpful in reducing the temperature of pavement and enhancing the ability of heat resistance, and the optimal effect can reduce the bottom surface temperature about 2.6 °C when ceramsite ratio is 60%. Because of the improvement in the dynamic stability and the thermal conductivity, CAM can have a good rutting resistance and the recommended ceramsite ratio is 60%.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Evaluation of factors that affect rutting resistance of asphalt mixes by orthogonal experiment design10.1016/j.ijprt.2017.03.008 ↗
2. Fracture resistance of asphalt concrete under different loading modes and temperature conditions10.1016/j.conbuildmat.2013.11.096 ↗
3. Gradation-based framework for asphalt mixture10.1617/s11527-012-9982-3 ↗
4. Rheological properties of bitumen modified with ethylene butylacrylate glycidylmethacrylate10.1002/pen.23649 ↗
5. New high-temperature binder specification using multistress creep and recovery
6. Effect of poly phosphoric acid on asphalt binder properties
7. Susceptibility of asphalt binders to rutting: literature review[J]10.1061/(ASCE)MT.1943-5533.0001364 ↗
8. Rheological examination of aging in polymer-modified asphalt10.1061/(ASCE)MT.1943-5533.0001370 ↗
9. Solar heating reflective coating layer (SHRCL) to cool the asphalt pavement surface10.1016/j.conbuildmat.2017.02.087 ↗
10. Comparison and analysis on heat reflective coating for asphalt pavement based on cooling effect and anti-skid performance10.1016/j.conbuildmat.2015.04.043 ↗
11. A novel polynary fatty acid/sludge ceramsite composite phase change materials and its applications in building energy conservation10.1016/j.renene.2014.11.001 ↗
12. Microstructure and performance of sludge-ceramsite concrete10.1016/j.conbuildmat.2012.05.004 ↗
13. The mechanical characteristics of steam-cured high strength concrete incorporating with lightweight aggregate10.1016/j.conbuildmat.2016.12.171 ↗
14. Laboratory evaluation of incorporating waste ceramic materials into Portland cement and asphaltic concrete10.1016/j.conbuildmat.2009.08.024 ↗
15. Utilizing recycled ceramic aggregates obtained from tile industry in the design of open graded wearing course on both laboratory and in situ basis10.1016/j.matdes.2013.03.041 ↗
16. Using ceramic wastes from tile industry as a partial substitute of natural aggregates in hot mix asphalt binder courses10.1016/j.conbuildmat.2013.03.058 ↗
17. Investigation of waste ceramic tile additive in hot mix asphalt using fuzzy logic approach10.1016/j.conbuildmat.2017.03.025 ↗
18. Performance and thermal evaluation of incorporating waste ceramic aggregates in wearing layer of asphalt pavement10.1061/(ASCE)MT.1943-5533.0000788 ↗
19. Research on the thermal insulating performance of ceramic asphalt concrete based on thermophysical properties10.1061/JHTRCQ.0000494 ↗
20. JTG E42-2005, Test Method of Aggregate for Highway Engineering.
21. JTG E20-2011, Standard Test Methods of Bitumen and Bituminous Mixtures for Highway Engineering.
22. GB/T 2424.14-1995, Environmental for Electric and Electronic Products. Part 2: Guidance for Solar Radiation Testing.
23. T324 “Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Hot-Mix Asphalt (HMA)”
24. T283 “Standard Method of Test for Resistance of Compacted Hot Mix Asphalt (HMA) to Moisture-Induced Damage”