journal article·2020-12

Evaluating the properties of zinc production wastes as filler and their effects on asphalt mastic

Hasan Taherkhani, Sasan Vahabi Kamsari

Publisher page

Abstract

Abstract This study evaluated four types of zinc production waste and limestone powder to be used as filler in asphalt mixtures. The properties of the fillers, asphalt mastic and mixtures made by the fillers were investigated. Only the results for fillers and mastics are provided. The physical and chemical properties and morphology of waste fillers, namely cobalt cake, leach cake, nickel cake, and zinc ash, as well as the limestone powder, as control filler, were examined. The moisture content, particle and bulk density, methylene blue value (MBV), Rigden voids (RV), pH, chemical compositions, morphology, hydrophobicity, size distribution, solubility in water, and specific surface area of the fillers were evaluated. Also, using a constant volumetric filler to binder ratio, asphalt mastics were made and their softening point, ductility, penetration grade and rheological properties were measured and compared with neat binder. Evaluation of the properties of fillers showed that the fillers can be potentially used in asphalt mixtures. Zinc ash had comparable and even better properties than the control filler. In terms of hydrophobicity, solubility in water and moisture content, the best performance belonged to zinc ash, followed by limestone, nickel, cobalt, and leach cake, respectively. Leach and cobalt cake showed to be hydrophilic fillers. The lowest MBV was found for the zinc ash, followed by limestone, nickel, leach and cobalt cake. The highest RV was found for the leach cake, and lowest for zinc ash filler. The fillers have different levels of stiffening effect on the mastic. In terms of temperature susceptibility using the softening point test results, the lowest sensitivity was obtained for zinc ash followed by cobalt cake, leach cake, limestone, and nickel cake. However, penetration and DSR test results revealed that the highest stiffening effect was obtained using zinc ash followed by cobalt cake, nickel cake, limestone, and leach cake. The stiffening effect of the fillers can be described by the morphology of filler particles; however, RV cannot be directly related to the stiffening effect of the fillers.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (65)

Show source-provided references
1. EAPA, Asphalt in Figures 2017 (2017). Available online: https://eapa.org/userfiles/2/Asphalt%20in%20Figures/2016/AIF_2016.pdf (accessed on 15 February 2019).
2. NAPA, Asphalt Pavement Industry Survey on Recycled Materials and Warm-Mix Asphalt Usage. NAPA (2017). http://www.asphaltpavement.org/PDFs/IS138/IS138-2017_RAP-RAS-WMA_Survey_Final.pdf (accessed 20 February 2019).
3. Fly ash as low cost and environmentally friendly filler and its effect on the properties of mix asphalt10.1016/j.jclepro.2019.06.353 ↗
4. Eurostat, Eurostat—data explorer (2015). http://appsso. eurostat.ec.europa.eu/nui/show.do (accessed 11 April 2016).
5. Investigation of regional conditions and sustainability indicators for sustainable product development of building materials10.1016/j.jclepro.2018.06.057 ↗
6. Experimental study on stiffness development of asphalt mixture containing cement and Ca(OH)2 as contribution filler10.1016/j.matdes.2015.02.026 ↗
7. Fatigue characteristics of bitumen-filler mastics and asphalt mixtures10.1061/(ASCE)MT.1943-5533.0000450 ↗
8. Development of high performance asphalt mastic using fine taconite filler10.1007/s12205-014-1207-6 ↗
9. Experimental investigation on related properties of asphalt mastic containing recycled red brick powder10.1016/j.conbuildmat.2010.12.040 ↗
10. Laboratory Investigation of crumb rubber modified asphalt binder and mixtures with warm-mix additives10.1007/s40999-016-0040-3 ↗
11. Effect of mineral fillers on oxidative aging of asphalt binders: laboratory study using mastics10.3141/2506-03 ↗
12. Effect of the chemical composition of fillers in the filler-bitumen interaction10.1016/j.conbuildmat.2015.12.042 ↗
13. F.M. Jakarni, Adhesion of asphalt mixtures, Phd Thesis, University of Nottingham, Nottingham, UK, 2011.
14. An empirical framework for determining asphalt mastic viscosity as a function of mineral filler concentration10.1016/j.conbuildmat.2012.02.093 ↗
15. New conceptual model for filler stiffening effect on asphalt mastic of microsurfacing10.1061/(ASCE)MT.1943-5533.0001264 ↗
16. Effects of filler characteristics on the performance of asphalt mastic: a statistical analysis of the laboratory testing results10.1007/s40999-017-0272-x ↗
17. Investigating influence of mineral filler at asphalt mixture and mastic scales10.1016/j.ijprt.2017.10.008 ↗
18. Influence of the geometrical and physical properties of filler in the filler–bitumen interaction10.1016/j.conbuildmat.2014.12.008 ↗
19. A simple test method in order to assess the effect of mineral fillers on bitumen ageing10.1016/j.conbuildmat.2016.05.003 ↗
20. V. Antunes, A.C. Freire, L. Quaresma, R. Micaelo, Evaluation of waste materials as alternative sources of filler in asphalt mixtures, Mater. Struct. 50 (6) (2017) 254.10.1617/s11527-017-1126-3 ↗
21. M. Saltan, B. Öksüz, V.E., Uz, Use of glass waste as mineral filler in hot mix asphalt, Sci. Eng. Compos. Mater. 22 (3) (2015) 271–277.10.1515/secm-2013-0135 ↗
22. Properties of hot mix asphalt with substituted waste glass10.1617/s11527-014-0492-3 ↗
23. Evaluation of steel slag powder as filler in hot-mix asphalt mixtures10.1520/ACEM20170080 ↗
24. Utilization of recycled brick powder as alternative filler in asphalt mixture10.1016/j.conbuildmat.2010.08.005 ↗
25. Utilizing of waste ceramic powders as filler material in self-consolidating concrete10.1016/j.conbuildmat.2017.05.180 ↗
26. Potential of recycled fine aggregates powder as filler in asphalt mixture10.1016/j.conbuildmat.2011.04.022 ↗
27. Effect of using waste material as filler in bituminous mix design10.11648/j.ajce.20150303.16 ↗
28. Application of coal waste powder as filler in hot mix asphalt10.1016/j.conbuildmat.2014.06.002 ↗
29. Water susceptibility of asphalt mixtures as influenced by hydraulically active fillers10.1617/s11527-013-0220-4 ↗
30. N.M. Katamine, Phosphate waste in mixtures to improve their deformation. J. Transp. Eng-ASCE. 126 (5) (2000) 382–389.10.1061/(ASCE)0733-947X(2000)126:5(382) ↗
31. Effect of using fly ash as alternative filler in hot mix asphalt10.1016/j.pisc.2016.04.061 ↗
32. E. Santagata, M. Bassani, O. Baglieri, Use of vitrified municipal solid waste bottom ash as a filler substitute in asphalt mixtures, Sustainability, Eco-Efficiency and Conservation in Transportation Infrastructure Asset Management (2014) 15–21.
33. Experimental evaluation of ceramic waste as filler in hot mix asphalt10.1007/s10098-019-01788-9 ↗
34. A study on engineering characteristics of asphalt concrete using filler with recycled waste lime10.1016/j.wasman.2006.11.011 ↗
35. M. Wasilewska, D. Małaszkiewicz, N. Ignatiuk, Evaluation of different mineral filler aggregates for asphalt mixtures, Mater. Sci. Eng. C, 245 (2) (2017) 022042-116.10.1088/1757-899X/245/2/022042 ↗
36. Influence of aggregate particles on mastic and air-voids in asphalt concrete10.1016/j.conbuildmat.2015.05.031 ↗
37. Effects of using brake pad waste powder as a filler material on the rheological and mechanical properties of a sulfur modified asphalt mixture10.1016/j.conbuildmat.2018.12.007 ↗
38. Laboratory investigation on the properties of asphalt concrete mixture with Rice Husk Ash as filler10.1016/j.conbuildmat.2016.09.070 ↗
39. Mechanical properties of roller compacted concrete containing rice husk ash with original and recycled asphalt pavement material10.1016/j.matdes.2014.07.072 ↗
40. Evaluation of incorporating oil shale filler aggregate into hot mix asphalt using Superpave mix design10.1016/j.conbuildmat.2015.10.071 ↗
41. Moisture damage resistance of hot-mix asphalt made with paper industry wastes as filler10.1016/j.jclepro.2015.06.016 ↗
42. Assessment of waste bleaching clay as alternative filler for the production of porous asphalts10.1016/j.conbuildmat.2016.01.052 ↗
43. S.J. Khamesy, A.H. Hamidian, O. Atghia, Identification of the fungi absorbing heavy metals isolated from waste deposits of zinc factories. Mycologia Iranica, 3 (1) (2016) 65–73.
44. EN 1097-5, Tests for Mechanical and Physical Properties of Aggregates—Part 5: Determination of the Water Content by Drying in a Ventilated Oven; British Standards Institution, London, UK, 2008.
45. EN 1097-7, Tests for Mechanical and Physical Properties of Aggregates—Part 7: Determination of the Particle Density of Filler–Pyknometer Method; British Standards Institution, London, UK, 2008.
46. ASTM, Standard test method for the Mechanical and Physical Properties of Aggregates., Determination of the Tap density (bulk volume density). ASTM D-854, American Society for Testing and Materials, 2006.
47. AASHTO, Standard T330-07: The qualitative detection of harmful clays of the smectite group in aggregates using methylene blue. American Association of State Highway and Transportation Officials, 2011.
48. EN 1744-1, Tests for Chemical Properties of Aggregates—Part 1–Chemical Analysis; British Standards Institution, London, UK, 2009.
49. Osman · 2004
50. EN 13179-1, Tests for Filler Aggregate Used in Bituminous Mixtures—Part 1–Delta Ring and Ball Test; British Standards Institution, London, UK, 2013.
51. Quaresma · 2002
52. ASTM, Standard Test Method for Ductility of Asphalt Materials; ASTM D113, American Association of State Highway and Transportation Officials, 2017.
53. ASTM · 2006
54. Alternative fillers for the production of bituminous mixtures: a screening investigation on waste powders10.3390/coatings7060076 ↗
55. G. Wypych, Handbook of fillers. ISBN 1-895198 19-4. Chem. Tec Publishing. Toronto. Canada, 1999.
56. R. Taylor, Surface interactions between bitumen and mineral fillers and their effects on the rheology of bitumen-filler mastics. Ph.D Thesis. Nottingham School of Civil Engineering, UK, 2010.
57. Curtis · 1993
58. Moisture damage assessment using surface energy, bitumen stripping and the SATS moisture conditioning procedure10.1080/10298436.2015.1007235 ↗
59. D. Little, J. Epps, The benefits of hydrated lime in hot mix asphalt (Updated version by Peter E. Sebaaly in 2006), fifth ed. National Lime Association, USA, 2006.
60. C. Clopotel, H. Bahia, The effect of bitumen polar groups adsorption on mastics properties at low temperatures. Road Mater. Pavement Des. 14 (2013) 38–51, doi: 10.1080/14680629.2013.774745.10.1080/14680629.2013.774745 ↗
61. R. Geber, L. Gomez, Characterization of mineral materials as asphalt fillers, Mater. Sci. Forum, 659 (2010) 471–476, doi: 10.4028/www.scientific.net/MSF.659.471.10.4028/www.scientific.net/MSF.659.471 ↗
62. Experimental study of the effect of filler on the ductility of filler-bitumen mastics10.1016/j.conbuildmat.2018.09.063 ↗
63. D.N. Little, A. Bhasin, R. Lytton, Micromechanics modeling of performance of asphalt concrete based on surface energy, Model. Asph. Concr., McGraw-Hill Professional(2009). https://accessengineeringlibrary.com/browse/modeling-ofasphalt-concrete/p20017c1a9970355001 (accessed July 14, 2017).
64. An investigation of asphalt durability: relationships between ductility and rheological properties for unmodified asphalts Pet
65. Low-temperature ductility in relation to pavement performance