The effect of waste low-density polyethylene on the mechanical properties of thin asphalt overlay
Source abstract
Abstract
In recent years, there has been a huge demand for innovative methods to upcycle waste materials. This study aims to explore and evaluate the effect of using waste low-density polyethylene (w-LDPE), collected from waste plastic bags for domestic purposes, on the mechanical properties of dense Thin Asphalt Overlay (TAO). Waste materials have been deemed appropriate in the development of asphalt pavement mixtures, due to the expected enhancement in mixture properties further to the reduction in cost and saving natural resources. Three dosages of w-LDPE were incorporated with asphalt binder: 2%, 4%, and 6%. Marshall stability and flow test, indirect tensile strength, creep compliance, skid resistance, wheel track, Cantabro abrasion loss and tensile strength ratio tests were carried out on both control and modified asphalt mixes to achieve the aim of the study. The results show a substantial enhancement in the performance of TAO modified with w-LDPE when compared to the control mix. The pre-eminent improvement was obtained in the creep compliance test, in which the creep compliance value decreased by 83% compared to the control mixture when using 6% of w-LDPE. This study indicated that using waste material is an effective method of asphalt modification that also contributes to promoting environmental sustainability.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Geotechnical and construction materials studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. A review of using thin white topping overlays for rehabilitation of asphalt pavements
2. Walubita, L.F. and Scullion, T., Thin HMA overlays in Texas: Mix design and laboratory material property characterization. 2008.
3. Newcomb, D.E., Thin asphalt overlays for pavement preservation. 2009.
4. Effect of polymer on the properties of bitumen and pavement layers, case study: expressway No.1, republic of iraq10.1088/1757-899X/1090/1/012032 ↗
5. Relation between polymer architecture and nonlinear viscoelastic behavior of modified asphalts10.1016/j.cocis.2006.09.001 ↗
6. Polymer modification of bitumen
7. Bitumen modifiers for reduced temperature asphalts: A comparative analysis between three polymeric and non-polymeric additives10.1016/j.conbuildmat.2013.11.009 ↗
8. Behavior of asphalt concrete mixtures with reclaimed polyethylene as additive10.1061/(ASCE)0899-1561(2007)19:6(500) ↗
9. Durability assessment of open-graded friction course using a sustainable polymer10.1007/s42947-020-6013-6 ↗
10. Dulaimi, A., Al Nageim, H., Ruddock, F. and Seton, L. Assessment the Performance of Cold Bituminous Emulsion Mixtures with Cement and Supplementary Cementitious Material for Binder Course Mixture. in The 38th International Conference on Cement Microscopy. 2016.
11. Characterizing cold bituminous emulsion mixtures comprised of palm leaf ash10.1061/(ASCE)MT.1943-5533.0002714 ↗
12. Application of waste materials as fillers in bituminous mixes10.1016/j.wasman.2018.06.009 ↗
13. Al-Busaltan, S., Al-Nageim, H., Atherton, W., George, S., Seton, L. and Dempster, N. Use of SEM and XRD for characterisation the improvement in CMEM’s engineering properties. in Proc. in 34th Inter. Conf. Cement Microscopy. 2012.
14. Shakir Al-Busaltan, Hassan Al Nageim, William Atherton, George Sharples, Linda Seton and Nicola Dempster. Use Of SEM And XRD for Characterisation the Improvement in CBEMs Engineering Propertie. in Proceedings of 34th International Conference on Cement Microscopy. 2012. Halle, Germany.
15. Al Nageim, H., Dulaimi, A., Ruddock, F. and Seton, L., Development of a New Cementitious Filler for Use in Fast-Curing Cold Binder Course in Pavement Application, in The 38th International Conference on Cement Microscopy. 2016: Lyon, France.
16. Dulaimi, A., Al Nageim, H., Ruddock, F. and Seton, L., Microanalysis of Alkali-Activated Binary Blended Cementitious Filler in a Novel Cold Binder Course Mixture, in The 38th International Conference on Cement Microscopy. 2016: Lyon, France.
17. Evaluation of corn husk fibers reinforced recycled low density polyethylene composites10.1016/j.matchemphys.2014.12.004 ↗
18. Effect of polyethylene on life of flexible pavements10.1016/j.conbuildmat.2008.07.004 ↗
19. The use of polyethylene in hot asphalt mixtures10.3844/ajassp.2007.390.396 ↗
20. Low density polyethylene modified dense graded bituminous macadam10.14445/22315381/IJETT-V16P273 ↗
21. Eme, D. and Nwaobakata, C.J.N.J.o.T., Effect of low density polyethylene as bitumen modifier on some properties of hot mix asphalt. 2019. 38(1): p. 1–7.10.4314/njt.v38i1.1 ↗
22. GSRB, General Specification for Roads and Bridges. 2003.
23. ASTM, Standard test method for relative density (specific gravity) and absorption of fine aggregate. 2015.
24. ASTM, Standard test method for materials finer than 75-μm (No. 200) sieve in mineral aggregates by washing. 2013.
25. ASTM, “Standard Test Method for Clay Lumps and Friable Particles in Aggregates,” vol. 97, no. 2010, Reapproved.
26. ASTM, Standard test method for sand equivalent value of soils and fine aggregate. 2014b.
27. ASTM, A. Standard test method for relative density (specific gravity) and absorption of coarse aggregate. 2015. ASTM West Conshohocken, PA.
28. ASTM, ASTM C131-03 'Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles Machine'. 2003a.
29. ASTM, ASTM D5-D5M - 13 'Standard test method for penetration of bituminous materials'. 2013.
30. ASTM, ASTM D 113 - 07 'Standard test method for ductility of bituminous materials'. 2007.
31. ASTM, ASTM D 36 – 95 (Reapproved 2000) 'Standard test method for softening point of bitumen (ring-and-ball apparatus)'. 2009a.
32. ASTM, D4402 (2002) 'Standard test method for viscosity determination of asphalt at elevated temperatures using a rotational viscometer'.
33. ASTM. Standard practice for preparation of bituminous specimens using Marshall apparatus. 2010 American Society for Testing and Materials USA.
34. BSI, BS EN 12697-22 2003 'Bituminous mixtures test methods for hot mix asphalt'. 2003.
35. Using waste plastic bottles as additive for stone mastic asphalt10.1016/j.matdes.2011.06.016 ↗
36. Performance evaluation of utilization of waste Polyethylene Terephthalate (PET) in stone mastic asphalt10.1016/j.conbuildmat.2012.06.015 ↗
37. Institute · 2014
38. ASTM, Standard test method for Marshall stability and flow of asphalt mixtures. 2015.
39. AASHTO, Standard Method of Test for: Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage. . 2007.
40. AASHTO T 283, Standard method of test for resistance of compacted asphalt mixtures to moisture-induced damage. AASHTO Provisional Standards: Washington, DC, USA, 2021.
41. AASHTO, Determining the creep compliance and strength of hot mix asphalt (HMA) using the indirect tensile test device. 2011.
42. ASTM, Standard test method for measuring surface frictional properties using the British pendulum tester. 2013.
43. BSI, 12697/32: 2003 (2003).“. 2003.10.1049/ee.2003.0037 ↗
44. Doyle, J.D. and Howard, I.L., Evaluation of the cantabro durability test for dense graded asphalt, in Geo-Frontiers 2011: Advances in Geotechnical Engineering. 2011. pp. 4563–4572.10.1061/41165(397)467 ↗
45. ASTM, Standard practice for open-graded friction course (OGFC) mix design. 2013, American Society for Testing and Materials [ASTM] Philadephia, PA.
46. AASHTO, Standard method of test for resistance of compacted asphalt mixtures to moisture-induced damage. AASHTO Provisional Standards: Washington, DC, USA, 2007.
47. Sadeque, M., Patil, K.J.F.U., Series: Architecture and Engineering, C., Marshall properties of waste polymer and nanoclay modified bitumen. 2014: p. 1-9.10.2298/FUACE1401001S ↗
48. Morphology, rheology, and physical properties of polymer-modified asphalt binders10.1016/j.eurpolymj.2018.10.049 ↗
49. Rheological properties, compatibility, and storage stability of SBS latex-modified asphalt10.3390/ma12223683 ↗
50. Innovative application of waste polyethylene terephthalate (PET) derived additive as an antistripping agent for asphalt mixture: Experimental investigation and molecular dynamics simulation10.1016/j.fuel.2021.121015 ↗
51. Benefits of utilization the recycle polyethylene terephthalate waste plastic materials as a modifier to asphalt mixtures10.1016/j.conbuildmat.2019.05.172 ↗
52. AASHTO T 322, Standard method of test for determining the creep compliance and strength of hot mix asphalt (HMA) using the indirect tensile test device. AASHTO Provisional Standards: Washington, DC, USA, 2007.
53. Angelone, S., Casaux, M.C., Borghi, M., Martinez, F.O.J.M. and Structures, Green pavements: reuse of plastic waste in asphalt mixtures. 2016. 49(5): p. 1655-1665.10.1617/s11527-015-0602-x ↗
54. Ahmed, S., Fracture characterization of thin bonded asphalt concrete overlay systems. 2011, University of Illinois at Urbana-Champaign.
55. Experimental investigation on skid resistance of asphalt pavement under various slippery conditions10.1080/10298436.2015.1095901 ↗
56. Green pavements: reuse of plastic waste in asphalt mixtures10.1617/s11527-015-0602-x ↗