Analysis of influence of ballast shape on abrasion resistance using discrete element method
Source abstract
Abstract
Abstract The ballast resistance performance—an important indicator of the performance and maintenance of railway ballast—is strongly dependent on the ballast shape, but this relationship is not yet fully understood. Despite many attempts to model the constitutive behavior of the ballast under cyclic loading using the discrete element method (DEM), few studies have obtained any conclusive results on the ballast breakage behavior. Therefore, in this study, a series of innovative techniques have been adopted to develop a crushable-ballast DEM model, and this model is further calibrated using the results of the Los Angeles abrasion (LAA) test. The results indicate both needle-shaped and flake-shaped ballast samples tend to break more easily than the normal-shaped samples. Thus, only the normal-shaped ballast samples are recommended for LAA test. Furthermore, by considering the ballast dynamic stability, a strict restriction on the proportion of needle-shaped ballast (≤10%) was recommended as the relevant technical standard.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Railway Engineering and Dynamics · Geotechnical Engineering and Underground Structures · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Indraratna · 2011
2. Selig · 1994
3. Behaviour of clay-fouled ballast under cyclic loading10.1680/geot.13.T.033 ↗
4. Behaviour of clay-fouled ballast under drained triaxial testing10.1680/geot.11.P.086 ↗
5. Discrete element modelling of railway ballast under monotonic and cyclic triaxial loading10.1680/geot.2010.60.6.459 ↗
6. Lim · 2004
7. D.W. Fowler et al.: The prediction of coarse aggregate performance by micro-deval and other aggregate tests. International Center for Aggregate Research ICAR Report, State of Texas (2006).
8. Aursudkij · 2007
9. Noålsund · 2013
10. Characterizing ballast degradation through Los Angeles Abrasion test and image analysis10.3141/2448-17 ↗
11. A discrete numerical model for granular assemblies10.1680/geot.1979.29.1.47 ↗
12. Discrete element modeling of ballast settlement under trains moving at “Critical Speeds”10.1016/j.conbuildmat.2012.09.007 ↗
13. Discrete Element Modeling for fouled railroad ballast10.1016/j.conbuildmat.2011.03.019 ↗
14. Three-dimensional laser scanning technique to quantify aggregate and ballast shape properties10.1016/j.conbuildmat.2013.02.062 ↗
15. Behavior of fresh and fouled railway ballast subjected to direct shear testing: Discrete Element Simulation10.1061/(ASCE)GM.1943-5622.0000264 ↗
16. From theory to practice in track geomechanics-Australian perspective for synthetic inclusions10.1016/j.trgeo.2014.07.004 ↗
17. Experimental and numerical study of railway ballast behavior under cyclic loading10.1061/(ASCE)GM.1943-5622.0000055 ↗
18. B.A. Wills, J.A. Finch. Chapter 17: Modeling and Characterization. in Wills' Mineral Processing Technology (Eighth Edition) (2015).10.1016/B978-0-08-097053-0.00017-0 ↗
19. Three-dimensional laser scanning technique to quantify aggregate and ballast shape properties10.1016/j.conbuildmat.2013.02.062 ↗
20. Forbes · 2006 · 165
21. Discrete element modelling of railway ballast under triaxial conditions10.1080/17486020802485289 ↗
22. National Railway Administration of the People’s Republic of China. TB/T 2328 Railway ballast -Part 2:test methods (2018).
23. Xu · 2016
24. Fine modelling of ballast grains and influence on mechanical properties of track bed
25. G.R. McDowell, H. Li, Discrete element modelling of scaled railway ballast under triaxial conditions Granular Matter (2016).10.1007/s10035-016-0663-8 ↗