Long-term performance and hydration of cement mortars with hydroxyethyl methyl cellulose cured at 5℃ low temperature
Source abstract
Abstract
Abstract As one of the special curing regimes, low temperature environment is considered to be crucial to the development of various properties of cementitious materials. This work focuses on the long-term performance and hydration of cement mortars with hydroxyethyl methyl cellulose (HEMC) cured at 5℃. The results show that the mid-late flexural and compressive strengths decrease with the HEMC content increasing, to get the lowest values at 1% HEMC. Afterwards, with the HEMC content increasing to 3%, the above strengths gradually increase, still being lower than those of the control. The tensile bond strength increases with the HEMC content increasing, to reach the maximum value at 0.3–0.5% HEMC, and then decreases with the HEMC content increasing to 3%, which is still much higher than that of the control. The drying shrinkage presents a significant increase with the HEMC content increasing. Moreover, HEMC significantly retards the early hydration of cement pastes. But the final hydration degree of cement pastes with HEMC tends to be close to that of the control. In addition, macro pores and the total porosity increase with the HEMC content increasing at 0–1%, and then decrease to some extent at 3% HEMC. Obviously, due to its better long-term properties at 5℃, the cement mortars with HEMC are still applicable at low temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Building materials and conservation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (65)
Show source-provided references
1. V. Lefebure, Improvements in or relating to concrete, cements, plasters and the like. British Patent 217, 279, 5 June 1924.
2. Cellulose ethers and water retention10.1016/j.cemconres.2013.06.010 ↗
3. Working mechanism of methyl hydroxyethyl cellulose (MHEC) as water retention agent10.1016/j.cemconres.2012.03.016 ↗
4. Influence of defoaming agents on mechanical performances and pore characteristics of Portland cement paste/mortar in presence of EVA dispersible powder
5. Effect of hydroxypropyl-methyl cellulose ether on rheology of cement paste plasticized by polycarboxylate superplasticizer10.1016/j.conbuildmat.2017.11.010 ↗
6. Synergistic effect of EVA, TEA and C-S-Hs-PCE on the hydration process and mechanical properties of Portland cement paste at early age10.1016/j.conbuildmat.2020.121891 ↗
7. The AC response of polymer-coated mortar specimens10.1016/S0008-8846(02)00741-X ↗
8. Study on waterproof mechanism of polymer-modified cement mortar10.1680/macr.14.00294 ↗
9. Influence of polymer latex on the setting time, mechanical properties and durability of calcium sulfoaluminate cement mortar10.1016/j.conbuildmat.2018.03.005 ↗
10. Influences of ethylene-vinyl acetate and methylcellulose on the properties of calcium sulfoaluminate cement10.1016/j.conbuildmat.2018.10.218 ↗
11. Influence of polymers on microstructure and adhesive strength of cementitious tile adhesive mortars10.1016/j.cemconres.2004.06.039 ↗
12. Development and use of polymer-modified cement for adhesive and repair applications10.1016/j.conbuildmat.2017.12.103 ↗
13. Influence of curing regimes on the mechanical properties, water capillary adsorption, and microstructure of CSA cement mortar modified with styrene-butadiene copolymer dispersion10.1061/(ASCE)MT.1943-5533.0002553 ↗
14. Investigation on concrete-PCM interface under elevated temperature: At material level and member level10.1016/j.conbuildmat.2016.08.067 ↗
15. Experimental investigations on polymer-modified concrete subjected to elevated temperatures10.1617/s11527-013-0107-4 ↗
16. Effects of different curing regimes on engineering properties of polymer-modified mortar10.1061/(ASCE)MT.1943-5533.0000394 ↗
17. Mechanical properties of polymer-modified concretes containing expanded polystyrene beads10.1016/j.conbuildmat.2005.08.001 ↗
18. Physical and mechanical properties of styrene–butadiene rubber emulsion modified cement mortars10.1016/j.cemconres.2004.07.012 ↗
19. Strength and hygric properties of ETICS applied at various temperature, using adhesives with different cellulose ethers
20. Pore size distribution of hydrated cement pastes modified with polymers10.1016/S0008-8846(01)00549-X ↗
21. Effect of pozzolans on the hydration process of Portland cement cured at low temperatures10.1016/j.cemconcomp.2013.05.007 ↗
22. The effects of low temperature curing on the compressive strength of ordinary and high performance concrete10.1016/j.conbuildmat.2004.04.033 ↗
23. Effect of temperature on the microstructure of calcium silicate hydrate (C-S-H)10.1016/j.cemconres.2013.06.008 ↗
24. Effect of temperature on the pore solution, microstructure and hydration products of Portland cement pastes10.1016/j.cemconres.2006.11.016 ↗
25. HPMC and HEMC influence on cement hydration10.1016/j.cemconres.2005.08.003 ↗
26. Influence of cellulose ethers molecular parameters on hydration kinetics of Portland cement at early ages10.1016/j.conbuildmat.2012.01.007 ↗
27. Effect of HEMC on the early hydration of Portland cement highlighted by isothermal calorimetry10.1007/s10973-014-4346-6 ↗
28. Xu, Influence of cellulose ethers on hydration products of Portland cement10.1007/s11595-011-0273-6 ↗
29. Cement hydration and microstructure formation in the presence of water-soluble polymers10.1016/j.cemconres.2008.10.003 ↗
30. Effects of hydroxyethyl methyl cellulose ether on the hydration and compressive strength of calcium aluminate cement10.1007/s10973-019-08820-6 ↗
31. Pore structure of mortars with cellulose ether additions – study of the air-void structure10.1016/j.cemconcomp.2015.04.016 ↗
32. Experimental research on controlling the floating of rubber particles in mortar based on the layering degree index10.1016/j.conbuildmat.2020.118567 ↗
33. GB/T 175-2007, Common Portland cement, National Standardization Management Committee, Beijing, China, 2007.
34. GB/T 8074-2008, Test methods for specific surface of cement-Blaine method, National Standardization Management Committee, Beijing, China, 2008.
35. GB/T 14684-2001, Sand for building, General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Beijing, China, 2001.
36. GB/T 1346-2011, Test methods for water requirement of normal consistency, setting time and soundness of the Portland cement, National Standardization Management Committee, Beijing, China, 2011.
37. JGJ/T 70-2009, Standard for test method of performance on building mortar, Ministry of Construction of the People's Republic of China, Beijing, China, 2009.
38. GB/T 29756-2013, Test methods of physical property for dry-mix mortar, National Standardization Management Committee, Beijing, China, 2013.
39. GB/T 17671-1999, Method of testing cements-determination of strength (ISO), The State Bureau of Quality and Technical Supervision of the People's Republic of China, Beijing, China, 1999.
40. Assessment and mechanism study of bleeding process in cement paste by 1H low-field NMR10.1016/j.conbuildmat.2015.09.062 ↗
41. Effect of cement type and limestone particle size on the durability of steam cured self-consolidating concrete10.1016/j.cemconcomp.2017.03.007 ↗
42. Investigation of the cellulose ethers effect on the Portland cement hydration by thermal analysis10.1007/s10973-012-2789-1 ↗
43. The use of thermal analysis to investigate the effects of cellulose ethers on the Portland cement hydration10.1007/s10973-011-2091-7 ↗
44. Effect of non-ionic cellulose ethers on properties of white Portland cement
45. Innovative materials made by adding cellulose ethers to cement mortars10.1016/j.protcy.2015.02.042 ↗
46. D.A.d. Silva, H.R. Roman, O.E. Alarcon, Influence of HEMC and EVA polymers on some properties of dry-set mortars, Proc. 6th. World Congr. Ceram. Tile Qual., Castellon (Spain), 2000, pp. 21-30.
47. Effects of hydroxyethyl cellulose and oxalic acid on the properties of cement10.1016/S0008-8846(03)00060-7 ↗
48. A 1H NMR relaxometry investigation of gel-pore drying shrinkage in cement pastes10.1016/j.cemconres.2016.04.013 ↗
49. A reassessment of mercury intrusion porosimetry by comparison with 1H NMR relaxometry10.1016/j.cemconres.2017.05.024 ↗
50. Use of bench-top NMR to measure the density, composition and desorption isotherm of C-S-H in cement paste10.1016/j.micromeso.2013.01.032 ↗
51. Densification of C−S−H measured by 1H NMR relaxometry10.1021/jp3102964 ↗
52. Probing development of microstructure of early cement paste using 1H low-field NMR10.1007/s11595-013-0801-7 ↗
53. The effects of cellulose ethers and limestone fillers in Portland cement-based mortars by 1H NMR relaxometry10.1007/s00723-016-0844-y ↗
54. NMR study on bleeding properties of the fresh cement pastes mixed with polycarboxylate (PCE) superplasticizers10.1016/j.conbuildmat.2019.117938 ↗
55. State of water in calcium sulfoaluminate cement paste modified by hydroxyethyl methyl cellulose ether
56. The microstructure development during bleeding of cement paste: an NMR study10.1016/j.cemconres.2019.105866 ↗
57. A novel method for semi-quantitative analysis of hydration degree of cement by 1H low-field NMR10.1016/j.cemconres.2020.106329 ↗
58. Hydration of calcium sulfoaluminate cements — experimental findings and thermodynamic modelling10.1016/j.cemconres.2009.08.014 ↗
59. Zeolite blended cements: evaluation of their hydration rate by means of thermal analysis10.1007/s10973-009-0056-x ↗
60. Evaluation of the hydration of Portland cement containing various carbonates by means of thermal analysis
61. P.K. Mehta, P.J.M. Monteiro, Concrete: microstructure, properties and materials, 2017.
62. Brandt · 2005
63. Quantitative microstructure analysis of polymer-modified mortars10.1046/j.1365-2818.2003.01230.x ↗
64. Pore structure of mortars with cellulose ether additions – mercury intrusion porosimetry study10.1016/j.cemconcomp.2014.06.005 ↗
65. Pore structure and mechanical properties of cement–lime mortars10.1016/j.cemconres.2007.02.023 ↗