Enhancement of brick-mortar shear bond strength using environmental friendly mortars
Source abstract
Abstract
Abstract Usage of masonry system in many regions of the world like the Eastern Mediterranean, the Middle East, India, and China is still significantly high, despite their highly energy and intensive emission. Most of the failures in this system are caused by low ductility of cement mortars. This type of failure could be seen in masonry structures in areas in east Iran after Kermanshah earthquake in 2017. The present study investigates the shear bond characteristics of structures constructed by masonry using green materials. “Taftan” natural pozzolan and two types of rice husk ash (RHA) were used in mix design of used mortars as green materials. In this investigation, a modified direct shear test (DST) device was used to determine brick-mortar shear bond strength. The proposed method of applying DST has the advantages of determining pure bond characteristics and applying various normal loads. For this purpose, two bricks were bonded by each type of mortar and then subjected to the shear load. Direct shear tests were performed on nine different types of mortars with different normal loads. The effect of increasing shear bond strength over time was also studied. Finally, friction angle and cohesion of each system were determined. The test results showed that waste materials such as RHA in mortar could be considered as appropriate and beneficial mortar additives. Using these additives resulted in enhanced mortar ductility and increased failure strain and also reduction in the cost of mortar and its detrimental environmental impacts.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Building materials and conservation · Concrete and Cement Materials Research · Masonry and Concrete Structural Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Influence of shear bond strength on compressive strength and stress–strain characteristics of masonry10.1617/s11527-008-9358-x ↗
2. The effect of joint thickness and other factors on the compressive strength of brickwork
3. Response of masonry bed joints in direct shear10.1061/(ASCE)0733-9445(1989)115:9(2276) ↗
4. Groot · 1993
5. Microstructure of the interface between brick and mortar
6. An experimental study of the interface between brick and mortar
7. Physico-chemical study of Cretan ancient mortars10.1016/S0008-8846(02)01030-X ↗
8. Analytical characterisation of ancient mortars from the archaeological Roman city of Pollentia (Balearic Islands, Spain)10.1016/j.aca.2005.10.058 ↗
9. Characteristics of cement-soil mortars10.1617/14197 ↗
10. Concrete mixtures made with ternary blended cements containing fly ash and rice-husk ash
11. M.K. Pateha, Contribution {à} la valorisation des sous-produits industriels et agricoles dans l’industrie du ciment, 1991.
12. Fly ash slag, silica fume, and natural pozzolans
13. Rice husk ash-based binders and their use in high strength concrete in Vietnam
14. Origin of the pozzolanic effect of rice husks10.1016/S0950-0618(00)00045-3 ↗
15. Microstructure and hardened state properties on pozzolan-containing concrete10.1016/j.conbuildmat.2017.02.120 ↗
16. Enhancement of durability of concrete composites containing natural pozzolans blended cement through the use of Polypropylene fibers10.1016/j.compositesb.2014.01.052 ↗
17. Rice husk ash blended cement: assessment of optimal level of replacement for strength and permeability properties of concrete10.1016/j.conbuildmat.2007.06.011 ↗
18. Use of rice husk ash in concrete10.1016/0262-5075(84)90019-8 ↗
19. Studies of the surface area and porosity of activated carbons prepared from rice husks10.1016/S0008-6223(00)00029-4 ↗
20. Studies on silica obtained from rice husk10.1016/S0272-8842(00)00068-7 ↗
21. Investigation of combustion of raw and acid-leached rice husk for production of pure amorphous white silica10.1007/BF01174029 ↗
22. Recovery of amorphous silica in pure form from rice husk10.1080/0371750X.1996.10804761 ↗
23. Effect of the combustion process on the structure of rice hull silica10.1016/0040-6031(81)80255-9 ↗
24. New test for determination of masonry tensile bond strength10.1061/(ASCE)0899-1561(2005)17:6(725) ↗
25. Bond characteristics of earth block masonry10.1061/(ASCE)0899-1561(1999)11:3(249) ↗
26. Sinha · 1967
27. Rôle de lettringite dans la liaison de type mécanique entra la terre cuite et la pâte de ciment-portland
28. Flexural bond strength of masonry using various blocks and mortars10.1007/BF02486202 ↗
29. Tensile bond strength of soil-cement block masonry couplets using cement-soil mortars10.1061/(ASCE)0899-1561(2006)18:1(36) ↗
30. Brick-Mortar Bond and Masonry Compressive Strength10.1061/(ASCE)0899-1561(2005)17:2(229) ↗
31. Brick-mortar bond and masonry compressive strength10.1061/(ASCE)0899-1561(2005)17:2(229) ↗
32. Friction and cohesion coefficients of composite concrete-to-concrete bond10.1016/j.cemconcomp.2014.10.003 ↗
33. Experimental behavior of jacketed reinforced concrete beams10.1061/(ASCE)0733-9445(2000)126:6(692) ↗
34. ASTM Standard C1314, “Standard Test Method for Compressive Strength of Masonry Prisms 1,” pp. 1–10, 2012.
35. ASTM Standard C33, “Standard Specification for Concrete Aggregates,” ASTM Int., vol. i, no. C, p. 11, 2003.
36. ASTM C566, “ASTM C566-97: Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying, ASTM C566-97,” Annu. B. ASTM Stand., vol. i, no. Reapproved, pp. 5–7, 2004.
37. Comparative study of the effects of microsilica and nanosilica in concrete10.3141/2141-02 ↗
38. Investigating the effects of using different types of SiO 2 nanoparticles on the mechanical properties of binary blended concrete10.1016/j.compositesb.2013.04.035 ↗
39. Improving the performance of cement-based composites containing superabsorbent polymers by utilization of nano-SiO 2 particles10.1016/j.matdes.2012.05.030 ↗
40. Silica gel from rice hull ash: preparation and characterization10.1094/CCHEM.1998.75.4.484 ↗
41. Biosorption of heavy metals using rice milling by-products. characterisation and application for removal of metals from aqueous effluents10.1016/j.chemosphere.2003.09.001 ↗
42. A. D5373, “Standard Test Methods for Determination of Carbon , Hydrogen and Nitrogen in Analysis Samples of Coal and Carbon in Analysis Samples of Coal and Coke 1,” 2017, pp. 1–11.
43. Effects of high volumes of fly ash, blast furnace slag, and bottom ash on flow characteristics, density, and compressive strength of high-strength mortar10.1061/(ASCE)MT.1943-5533.0000624 ↗
44. High strength concrete
45. I. Kett, Engineered Concrete, Mix Design and Test Methods, 2010
46. ASTM C230, “Standard Specification for Flow Table for Use in Tests of Hydraulic Cement 1,” Ann. B. ASTM Stand., pp. 4–9, 2010.
47. ASTM C1437, “Standard Test Method for Flow of Hydraulic Cement Mortar 1,” Am. Soc. Test. Mater., pp. 1–2, 2016.
48. ASTM C192/C192M, “Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory,” Am. Soc. Test. Mater., vol. 4, pp. 1–8, 2016.
49. High strength concrete containing natural pozzolan and silica fume10.1016/S0958-9465(00)00037-8 ↗
50. An experimental study on optimum usage of GGBS for the compressive strength of concrete10.1016/j.cemconcomp.2007.01.001 ↗