journal article·2019-02

Influence of scoria and pumice on key performance indicators of Portland cement concrete

Hieronimi A. Mboya, Karoli N. Njau, Alex L. Mrema, Cecil K. King'ondu

Publisher page

Abstract

Abstract Cement industries have a huge CO2 signature that can be reduced in an effort to mitigate climate change via precise cement substitution with supplementary cementing materials (SCMs). The substituting materials and their amounts ought not to degrade the key performance indicators of concrete such as slump, flow, permeability, shrinkage, modulus of rupture, compressive, and tensile splitting strength. In this study, the influence of natural scoria (SN) and pumice (PN) binders on the key performance indicators of the fresh and hardened Portland cement (PLC) concrete was successfully examined. The performance indicators were tested at PLC substitution (with SN or PN) levels of 10, 20, 30, and 40% and the results compared to the control (CTRL) made of PLC only. The results show that 10% is the optimum substitution level for both SN and PN. The compressive strength, modulus of rupture, shrinkage, permeability, and thermal stability of the concrete were not compromised at this substitution level. The 28 days modulus of rupture, shrinkage, and compressive strength for SN and PN at 10% substitution were 6.0 and 6.4 MPa; 0.02 and 0.01 mm; 44.2 and 43.1 MPa, respectively. These compared remarkably well with 6.3 MPa modulus of rupture, 0.01 mm shrinkage, and 43.1 MPa compressive strength of the control. Moreover, SN and PN delivered higher % residual compressive strength of 59.2 and 57.8%, correspondingly, after subjecting the concrete to high temperatures of 600 °C, compared to 52.6% for the control. Likewise, the coefficient of permeability (K) for SN (5.2526E−08 m/s) was similar to that of PLC (5.35714E−08 m/s). At substitution levels higher than 10%, more than one key performance indicators were negatively affected. These results show the utility of SN and PN in reducing the amount of cement used in construction and thus the CO2 emission associated with cement industries while at the same time preserving the strength, permeability, thermal and volume stability and hence the durability of the concrete.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Concrete Properties and Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Minimum cement content requirements : a must or a myth?10.1617/s11527-008-9436-0 ↗
2. Neville · 2010
3. Kett · 2010
4. Workability retention and compressive strength of self-compacting concrete incorporating pumice powder and silica fume10.1016/j.conbuildmat.2016.12.090 ↗
5. The effect of pumice powder on the self-compactability of pumice aggregate lightweight concrete10.1016/j.conbuildmat.2015.11.043 ↗
6. Influence of different amounts of natural pozzolan from volcanic scoria on the rheological properties of portland cement pastes10.1016/j.egypro.2017.11.274 ↗
7. Pumice powder as filler of self-compacting concrete10.1016/j.conbuildmat.2015.08.040 ↗
8. Pozzolan concrete durability on sulphate attack10.1016/j.proeng.2015.08.035 ↗
9. Shock-absorbing capability of lightweight concrete utilizing volcanic pumice aggregate10.1016/j.conbuildmat.2015.03.019 ↗
10. Non-structural lightweight concrete with volcanic scoria aggregates for lightweight fill in building’s floors10.1016/j.conbuildmat.2016.12.213 ↗
11. Ground granulated pumice-based cement mortars exposed to abrasion and fire10.1007/s13369-016-2403-0 ↗
12. Properties of high-volume fly ash concrete and its role in sustainable development
13. “Evaluation of sustainable high-volume fly ash concretes10.1016/j.cemconcomp.2010.09.020 ↗
14. Recent advances in understanding the role of supplementary cementitious materials in concrete10.1016/j.cemconres.2015.03.018 ↗
15. Calcined clay pozzolan as an admixture to mitigate the alkali-silica reaction in concrete
16. A review of sustainable supplementary cementitious materials as an alternative to all-portland cement mortar and concrete
17. Contribution of rice husk ash to the properties of cement mortar and concrete
18. Blended cement and lightweight concrete using scoria: mix design, strength, durability and heat insulation characteristics
19. Assessment of pumice blocks in comparison to cement sand blocks and burnt blocks ‘ The Case of Mbeya City – Tanzania’
20. Effect of basaltic pumice aggregate addition on the material properties of fly ash based lightweight geopolymer concrete10.1016/j.molstruc.2018.02.114 ↗
21. An investigation on the use of coarse volcanic scoria as sand in Portland cement mortar
22. Mechanical properties of lightweight aggregates concrete made with cameroonian volcanic scoria: Destructive and non-destructive characterization”10.1016/j.jobe.2018.01.003 ↗
23. SS-EN 197-1, Cement – Part 1: Composition, specification and conformity criteria for common cements, no. 123867. 2011.
24. Measurement of Pozzolanic Activity Index of Scoria, Pumice, and Rice Husk Ash as Potential Supplementary Cementitious Materials for Portland Cement
25. PD 6682-1:, “Aggregates — Part 1: Aggregates for concrete— Guidance on the use of BS EN 12620,” vol. 3, 2003.
26. BS 410, “BS 410:1986 Specification for test sieves,” Br. Stand., no. 1, pp. 10–13, 1986.10.1525/sfs.13.3.0410 ↗
27. SS-EN 196-6:2010, Methods of testing cement - Part 6: Determination of Fineness, no. 123867. 2010.
28. G.C. Cordeiro, R.D.T. Filho, L.M. Tavares, E.M.R. Fairbairm, S. Hempel, Influence of particle size and specific surface area on the pozzolanic activity of residual rice husk ash Cement & Concrete Composites of residual rice husk ash, no. MAY, 2011.10.1016/j.cemconcomp.2011.02.005 ↗
29. ASTM D 854, Standard Test for Specific Gravity of Soil Solids by Water Pycnometer, 2003
30. BSI, BS EN 12390-8:2009 Testing hardened concrete Part 8: Depth of Penetration of Water Under Pressure, 3(1), 420–457, 2009.
31. Water permeability characteristics of normal strength concrete made from crushed clay bricks as coarse aggregate10.1155/2017/7279138 ↗
32. BS EN 12620:, Aggregates for concrete, vol. 3, 2002.
33. BS EN 206-1, Concrete —Part 1: Specification, performance, production and conformity, vol. 3, 2000.
34. BS EN 12390-2:2000, Testing hardened concrete - Part 2: Making and curing specimens for strength tests, no. August, pp. 2–11, 2003.
35. BRE · 1997
36. BS EN 12350-1, BS EN 12350-2:2009 Testing fresh concrete Part 2: Slump-test, 2009.
37. BS EN 1350-7, Testing fresh concrete – Air content – Pressure method, 2009
38. BS EN 12350-6, Testing fresh concrete – Density, 2009.
39. BS 1881-116, Testing concrete — Part 116: Method for determination of compressive strength of concrete cubes, 1983.
40. BS EN 206, Concrete — Specification , performance , production and conformity, 2014.
41. SCCT, CSI: 2010 – Construction Standard, vol. 2. 2010.
42. ASTM C618, Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete, 2005
43. Mechanical strength development of mortars containing volcanic scoria-based binders with different fineness
44. Effects of alkali addition on the mechanical properties and durability of concrete10.1016/j.cemconres.2004.05.007 ↗
45. J.H. Ideker, T.Fu, T. Deboodt, Development of Shrinkage Limits and Testing Protocols for ODOT High Performance Concrete, Washington, 2013
46. ASTM C157, “Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and,” vol. 04, pp. 1–7, 2003.
47. Autogenous shrinkage of concrete: a balance between autogenous swelling and self-desiccation10.1016/j.cemconres.2004.05.050 ↗
48. Evaluation of activated high volume fly ash systems using Na 2 SO 4, lime and quicklime in mortars with high loss on ignition fly ashes10.1016/j.conbuildmat.2016.10.076 ↗